On Tuesday 10 May 2016 08:37:52 Benjamin Herrenschmidt wrote: > On Mon, 2016-05-09 at 17:08 +0200, Arnd Bergmann wrote: > > > > Unfortunately, I don't see any way this could be done in MIPS specific > > code: There is typically a byteswap between the internal bus and the PCI > > bus on big-endian MIPS systems, so the PCI MMIO ends up being little-endian, > > Ugh ... not exactly, re-watch my talk on the matter :-) While there is > a specific lane wiring to preserve byte addresss, in the end it's the > end device itself that is either BE or LE. Regardless of any "bus > endianness". I found your slides on http://www.linuxplumbersconf.org/2012/wp-content/uploads/2012/09/2012-lpc-ref-big-little-endian-herrenschmidt.odp but there are at least two more twists that you completely missed here: - Some architectures (e.g. ARMv5 "BE32" mode in IXP4xx, surely some others) do not implement big-endian mode by wiring up the data lines between the bus and the CPU differently between big- and little-endian mode like powerpc and armv7 "BE8" do, but instead they swizzle the *address* lines on 8-bit and 16-bit addresses. The effect of that is that normal RAM accesses work as expected both ways, and devices that are accessed using 32-bit MMIO ops never need any byteswap (you actually get "native endian") while MMIO with 8 and 16 bit width does something completely unexpected and touches the wrong register. Having an explicit byteswap on the PCI host bridge gets you the expected addresses again for 8-bit cycles but it also means that readl()/writel() again need to swap the data. - Some other architectures (e.g. Broadcom MIPS) apparently are even fancier and use a strapping pin on the SoC flips the endianess of the CPU core at the same time as all the peripheral MMIO registers, with the intention of never requiring any byte swaps. I believe they are implemented careful enough to actually get this right, but it confuses the heck out of Linux drivers that don't expect this. > > which matches the expected behavior of readl/writel. However, drivers > > for non-PCI devices often use the same readl/writel accessors because > > that is how it's done on ARMv6/ARMv7. > > Even then, you can have on-SoC (non-PCI) devices that also have a > different endianness from the main CPU. How does it work on ARM for > example ? The device endianness should be fixed, regardless of the > endianness of the core, no ? ARMv6/v7 is uses BE8 mode like powerpc: each peripheral is fixed-endian and you have to know what it is. Only Freescale managed to put identical IP blocks on various (powerpc-derived) SoCs and have a subset of them treat the access as little-endian while others remain big-endian, so all those drivers now require runtime detection. > > Doing it hardcoded by architecture is just the simplest way to deal > > with it, working on the assumption that nothing actually needs the > > runtime detection that Ben suggested. > > No, it's not an archicture problem. It's a problem specific to that one > SoC that the device was synthetized to be a certain endian while it was > synthetized differently on another SoC... that also happens to be a > different architecture. But doesn't have to. > > For example, we had in the past cases of both LE and BE EHCI > implementations on the same architecture (PowerPC). I understand this, but from what I see in this history of this particular driver, all ARM and PowerPC implementations chose to use LE registers for DWC2 because the normal approach for these is to not mess with endianess, while presumably all MIPS users of the same block wired up the endian-select line of the IP block to match that of the CPU core, again because it's what you are expected to do on a MIPS based SoC. So hardcoding it per architecture would make an assumption based on the mindset of the SoC designers rather than strict technical differences, and that can fail as soon as someone does things differently on any of them (see the Freescale example), but I still think it's the easiest workaround for backporting to stable kernels. A revert of the original patch would be even easier, but that would break the one big-endian MIPS machine we know about. > > Detecting the endianess of the > > device is probably the best future-proof solution, but it's also > > considerably more work to do in the driver, and comes with a > > tiny runtime overhead. > > The runtime overhead is probably non-measurable compared with the cost > of the actual MMIOs. Right. The code size increase is probably measurable (but still small), the runtime overhead is not. Arnd -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
