Hello,
I've been looking in getting the MyBook Live Duo's USB OTG port
to function. The SoC is a APM82181. Which has a PowerPC 464 core
and related to the supported canyonlands architecture in arch/powerpc/.
Currently in -next the dwc2 module doesn't load:
dwc2 4bff80000.usbotg: dwc2_core_reset() HANG! AHB Idle GRSTCTL=80
dwc2 4bff80000.usbotg: Bad value for GSNPSID: 0x0a29544f
Looking at the Bad GSNPSID value: 0x0a29544f. It is obvious that
this is an endian problem. git finds this patch:
commit 95c8bc3609440af5e4a4f760b8680caea7424396
Author: Antti Seppälä <a.seppala@xxxxxxxxx>
Date: Thu Aug 20 21:41:07 2015 +0300
usb: dwc2: Use platform endianness when accessing registers
This patch is necessary to access dwc2 registers correctly on big-endian
systems such as the mips based SoCs made by Lantiq. Then dwc2 can be
used to replace ifx-hcd driver for Lantiq platforms found e.g. in
OpenWrt.
The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
Some files were then hand-edited to fix checkpatch.pl warnings about
too long lines.
which unfortunately, broke the USB-OTG port on the MyBook Live Duo.
Reverting to the readl / writel:
---
diff --git a/drivers/usb/dwc2/core.h b/drivers/usb/dwc2/core.h
index 3c58d63..c021c1f 100644
--- a/drivers/usb/dwc2/core.h
+++ b/drivers/usb/dwc2/core.h
@@ -66,7 +66,7 @@
static inline u32 dwc2_readl(const void __iomem *addr)
{
- u32 value = __raw_readl(addr);
+ u32 value = readl(addr);
/* In order to preserve endianness __raw_* operation is used. Therefore
* a barrier is needed to ensure IO access is not re-ordered across
@@ -78,7 +78,7 @@ static inline u32 dwc2_readl(const void __iomem *addr)
static inline void dwc2_writel(u32 value, void __iomem *addr)
{
- __raw_writel(value, addr);
+ writel(value, addr);
/*
* In order to preserve endianness __raw_* operation is used. Therefore
---
restores the dwc-otg port to full working order:
dwc2 4bff80000.usbotg: Specified GNPTXFDEP=1024 > 256
dwc2 4bff80000.usbotg: EPs: 3, shared fifos, 2042 entries in SPRAM
dwc2 4bff80000.usbotg: DWC OTG Controller
dwc2 4bff80000.usbotg: new USB bus registered, assigned bus number 1
dwc2 4bff80000.usbotg: irq 33, io mem 0x00000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
root@mbl:~# usb 1-1: new high-speed USB device number 2 using dwc2
So, what to do?
Regards,
Christian
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
