Hi,
Felipe Balbi <felipe.balbi@xxxxxxxxxxxxxxx> writes:
>> Is something definitely wrong with initialization and enumeration traces?
>
> I'll go read them
> irq/19-dwc3-96 [000] d..2 824.785778: dwc3_event: event 00150301
Link State change -> RX.Detect
> irq/19-dwc3-96 [000] d..2 824.877339: dwc3_event: event 00040301
Link State Change SS.Disconnect
> irq/19-dwc3-96 [000] d..2 824.877343: dwc3_event: event 00000301
Link State Change U0
> irq/19-dwc3-96 [000] d..2 824.881192: dwc3_event: event 00050301
Link State Change RX.Detect
> irq/19-dwc3-96 [000] d..2 824.885004: dwc3_event: event 00030301
Link State Change U3
> irq/19-dwc3-96 [000] d..2 825.218156: dwc3_event: event 00000101
USB Reset
> irq/19-dwc3-96 [000] d..2 825.229241: dwc3_event: event 00000201
Conncect Done
> irq/19-dwc3-96 [000] d..2 825.229248: dwc3_gadget: Enabling ep0out
enable ep0 with correct parameters
> irq/19-dwc3-96 [000] d..2 825.229252: dwc3_gadget_ep_cmd: ep0out: cmd 'Set Endpoint Configuration' [1] params 80000200 00000500 00000000
aram0: 64bytes wMaxPacketSize, Ignore Sequence Number set
param1: XferComplete and XferNotReady for physical ep0
param2: nothing
> irq/19-dwc3-96 [000] d..2 825.229257: dwc3_gadget: Command Complete --> 0
completes fine
> irq/19-dwc3-96 [000] d..2 825.229259: dwc3_gadget: Enabling ep0in
> irq/19-dwc3-96 [000] d..2 825.229260: dwc3_gadget_ep_cmd: ep0in: cmd 'Set Endpoint Configuration' [1] params 80000200 02000500 00000000
param0: 64bytes wMaxPacketSize, Ignore Sequence Number set
param1: XferComplete and XferNotReady for physical ep1
param2: nothing
> irq/19-dwc3-96 [000] d..2 825.229264: dwc3_gadget: Command Complete --> 0
completes fine
So, basically everything here is fine. There's nothing wrong
here. However, Right after these you get:
> irq/19-dwc3-96 [000] d..2 825.229265: dwc3_event: event 00000301
> irq/19-dwc3-96 [000] d..2 825.322544: dwc3_event: event 00050301
> irq/19-dwc3-96 [000] d..2 825.323162: dwc3_event: event 00000101
> irq/19-dwc3-96 [000] d..2 825.329773: dwc3_event: event 00000201
> irq/19-dwc3-96 [000] d..2 825.329777: dwc3_gadget: Enabling ep0out
> irq/19-dwc3-96 [000] d..2 825.329782: dwc3_gadget_ep_cmd: ep0out: cmd 'Set Endpoint Configuration' [1] params 80000200 00000500 00000000
> irq/19-dwc3-96 [000] d..2 825.329786: dwc3_gadget: Command Complete --> 0
> irq/19-dwc3-96 [000] d..2 825.329788: dwc3_gadget: Enabling ep0in
> irq/19-dwc3-96 [000] d..2 825.329789: dwc3_gadget_ep_cmd: ep0in: cmd 'Set Endpoint Configuration' [1] params 80000200 02000500 00000000
> irq/19-dwc3-96 [000] d..2 825.329793: dwc3_gadget: Command Complete --> 0
All over again. And this repeats forever. Did you load a gadget driver ?
Which gadget driver did you load ?
--
balbi
Attachment:
signature.asc
Description: PGP signature
