On 02/25, Andy Gross wrote: > > On 25 February 2016 at 05:21, Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx> wrote: > >> > >> Andy/Bjorn, any comments on plans on corner regulators? > >> > >> Please note, that this is a patch to fix what is already in the mainline. > >> Without this patch the regulator would be configured with 1uV or 5uV or 7uV > >> which would obviously fail. > >> > >> THB, it does not make sense to drop feature which is functional, and I > >> also agree that we should cleanup some of this mess at some point in time > >> once we all the bits and pieces ready. > >> > >> I was surprised to see these usb bindings(qcom,vdd-levels) existed even > >> before we had concept of corner regulators in mainline kernel. Which also > >> suggests that this driver needs a proper relook once again. > > I think the vdd-levels were an oversight. The voltages definitely > need to be correct. As for the corner regulators, I believe the CPR > driver was supposed to address this. The USB requests a specific > voltage and frequency and based on this the CPR would set the corner > for the regulator. > > Stephen, correct me if i am wrong. There's CPR for the CPU voltage and there's CPR for the digital voltage. The RPM controls the latter, and so all we have on the Linux side is an API to request corners, not voltages, for digital logic. Almost everything in the SoC is using the digital voltage, so having USB be the only consumer of this voltage and then be the only driver telling the RPM what corner or voltage we want here is potentially very dangerous. Consider the case where USB goes to runtime suspend and USB driver says it only needs "low" voltage. This might cause RPM to go and lower the voltage because no other master in the system is asking for anything else besides "low". But we may have other hardware blocks using the digital logic supply in the system, e.g. GPU is running at max speed, and those blocks need "high" voltage. We just browned out the GPU. So maybe we should just remove this code from the USB driver for now? By default the voltage is nominal, and when the bus clocks are maxed out the voltage goes to the highest level. So as long as RPM bus clocks are maxed this code is not doing anything. My plan for handling corners is to hide it behind the OPP framework and/or generic power domains. The digital logic supply is really a regulator that supplies a large power domain called CX. All the digital logic in the SoC lives within this power domain. As an aside, it's quite typical that a hardware block sits in a few domains: digital, analog, memories, etc. so this may require us to expand the ability for devices to be in multiple PM domains at one time. But regardless, the frequency that a device in the digital logic domain is running at is used to pick a voltage that is "maxed" across all devices and factors into the voltage requirement of the domain. Another way to put it is that each device casts a "vote" for the CX voltage based on their frequency and the largest uV wins and is set. This is further complicated by CPR, which takes away the uV units from this calculation and transforms that into a "corner". Each hardware block now knows what voltage "corner" it needs for CX when their clock is at a particular frequency. We'll probably need to add some sort of "corner" property to the OPP binding to express this. Hopefully it can be a generic power domain level thing (keep reading!). So I'm thinking each device gets an OPP table of frequency to voltage/corner pairs. Devices would change their OPP through OPP framework and this would adjust the clk and voltage/corner appropriately. To make things generic between voltages and corners, we could hide that part behind the genpd framework by having OPP pick a "power level" that the power domain should be at. On SoCs where the power domain is supplied by a regulator the level would be translated into a uV (probably need some sort of level to uV table in DT or just put that in the code). On SoCs where the power domain is supplied by a regulator with corners, the level would be used as is and sent to the RPM. OPP framework wouldn't care, as long as the genpd driver handles the voltage vs. corner stuff. -- Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project -- To unsubscribe from this list: send the line "unsubscribe linux-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
