On Fri, 12 Apr 2024 13:57:01 +0300 (EEST)
Ilpo Järvinen <ilpo.jarvinen@xxxxxxxxxxxxxxx> wrote:
> On Thu, 11 Apr 2024, parker@xxxxxxxxx wrote:
>
> > From: Parker Newman <pnewman@xxxxxxxxxxxxxxx>
> >
> > - Removed old port setup function and replaced with UART specific ones
> > - Added board setup functions for CTI boards
> > - Replaced CONNECT_DEVICE macro with CTI_EXAR_DEVICE and CTI_PCI_DEVICE
>
> In general, you should try to do refactoring in a preparatory patch (one
> refactoring thing at a time) and add new stuff in another patch in
> the series. I didn't go to figure out how much it applies to those three
> items because you likely know the answer immediately.
>
> > - Moved "generic rs485" support up in the file
>
> Please do this in a separate patch.
>
Will do.
>
> Another general level problem with your series is that it adds functions
> x, y, etc. without users, whereas the expected way of doing things would
> be to add the functions in the change they are getting used so it's easier
> to follow what's going on.
>
> I believe if you separate the refactoring & moving code around into own
> changes (no functional change type patches), the new stuff is much
> smaller so there is no need to split that illogically into incomplete
> fragments in some patches.
>
> --
> i.
>
Thanks for the feedback, I am new to the mailing lists and am trying to balance
what you mention above with not having giant patches.
> > Signed-off-by: Parker Newman <pnewman@xxxxxxxxxxxxxxx>
> > ---
> > drivers/tty/serial/8250/8250_exar.c | 454 ++++++++++++++++++++++++----
> > 1 file changed, 401 insertions(+), 53 deletions(-)
> >
> > diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
> > index 6f3697e34722..d8425113a9f1 100644
> > --- a/drivers/tty/serial/8250/8250_exar.c
> > +++ b/drivers/tty/serial/8250/8250_exar.c
> > @@ -440,6 +440,31 @@ static int exar_mpio_set(struct exar8250 *priv,
> > return 0;
> > }
> >
> > +static int generic_rs485_config(struct uart_port *port, struct ktermios *termios,
> > + struct serial_rs485 *rs485)
> > +{
> > + bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
> > + u8 __iomem *p = port->membase;
> > + u8 value;
> > +
> > + value = readb(p + UART_EXAR_FCTR);
> > + if (is_rs485)
> > + value |= UART_FCTR_EXAR_485;
> > + else
> > + value &= ~UART_FCTR_EXAR_485;
> > +
> > + writeb(value, p + UART_EXAR_FCTR);
> > +
> > + if (is_rs485)
> > + writeb(UART_EXAR_RS485_DLY(4), p + UART_MSR);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct serial_rs485 generic_rs485_supported = {
> > + .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND,
> > +};
> > +
> > static void exar_pm(struct uart_port *port, unsigned int state, unsigned int old)
> > {
> > /*
> > @@ -875,15 +900,332 @@ static enum cti_port_type cti_get_port_type_xr17v35x(struct exar8250 *priv,
> > return port_type;
> > }
> >
> > -static int
> > -pci_connect_tech_setup(struct exar8250 *priv, struct pci_dev *pcidev,
> > - struct uart_8250_port *port, int idx)
> > +static int cti_rs485_config_mpio_tristate(struct uart_port *port,
> > + struct ktermios *termios,
> > + struct serial_rs485 *rs485)
> > {
> > - unsigned int offset = idx * 0x200;
> > - unsigned int baud = 1843200;
> > + struct exar8250 *priv;
> > + int ret;
> >
> > - port->port.uartclk = baud * 16;
> > - return default_setup(priv, pcidev, idx, offset, port);
> > + priv = (struct exar8250 *)port->private_data;
> > + if (!priv)
> > + return -EINVAL;
> > +
> > + ret = generic_rs485_config(port, termios, rs485);
> > + if (ret)
> > + return ret;
> > +
> > + //disable power-on tri-state via MPIO
> > + return cti_set_tristate(priv, port->port_id, false);
> > +}
> > +
> > +static int cti_port_setup_common(struct exar8250 *priv,
> > + int idx, unsigned int offset,
> > + struct uart_8250_port *port)
> > +{
> > + int ret;
> > +
> > + if (!priv || !port)
> > + return -EINVAL;
> > +
> > + if (priv->osc_freq == 0)
> > + return -EINVAL;
> > +
> > + port->port.port_id = idx;
> > + port->port.uartclk = priv->osc_freq;
> > +
> > + ret = serial8250_pci_setup_port(priv->pcidev, port, 0, offset, 0);
> > + if (ret) {
> > + pci_err(priv->pcidev,
> > + "failed to setup pci for port %d err: %d\n", idx, ret);
> > + return ret;
> > + }
> > +
> > + port->port.private_data = (void *)priv;
> > + port->port.pm = exar_pm;
> > + port->port.shutdown = exar_shutdown;
> > +
> > + return 0;
> > +}
> > +
> > +static int cti_port_setup_fpga(struct exar8250 *priv,
> > + struct pci_dev *pcidev,
> > + struct uart_8250_port *port,
> > + int idx)
> > +{
> > + enum cti_port_type port_type;
> > + unsigned int offset;
> > +
> > + port_type = cti_get_port_type_fpga(priv, idx);
> > +
> > + //FPGA shares port offests with XR17C15X
> > + offset = idx * UART_EXAR_XR17C15X_PORT_OFFSET;
> > + port->port.type = PORT_XR17D15X;
> > +
> > + port->port.get_divisor = xr17v35x_get_divisor;
> > + port->port.set_divisor = xr17v35x_set_divisor;
> > + port->port.startup = xr17v35x_startup;
> > +
> > + if (CTI_PORT_TYPE_RS485(port_type)) {
> > + port->port.rs485_config = generic_rs485_config;
> > + port->port.rs485_supported = generic_rs485_supported;
> > + }
> > +
> > + return cti_port_setup_common(priv, idx, offset, port);
> > +}
> > +
> > +static int cti_port_setup_xr17v35x(struct exar8250 *priv,
> > + struct pci_dev *pcidev,
> > + struct uart_8250_port *port,
> > + int idx)
> > +{
> > + enum cti_port_type port_type;
> > + unsigned int offset;
> > + int ret;
> > +
> > + port_type = cti_get_port_type_xr17v35x(priv, idx);
> > +
> > + offset = idx * UART_EXAR_XR17V35X_PORT_OFFSET;
> > + port->port.type = PORT_XR17V35X;
> > +
> > + port->port.get_divisor = xr17v35x_get_divisor;
> > + port->port.set_divisor = xr17v35x_set_divisor;
> > + port->port.startup = xr17v35x_startup;
> > +
> > + switch (port_type) {
> > + case CTI_PORT_TYPE_RS422_485:
> > + case CTI_PORT_TYPE_RS232_422_485_HW:
> > + port->port.rs485_config = cti_rs485_config_mpio_tristate;
> > + port->port.rs485_supported = generic_rs485_supported;
> > + break;
> > + case CTI_PORT_TYPE_RS232_422_485_SW:
> > + case CTI_PORT_TYPE_RS232_422_485_4B:
> > + case CTI_PORT_TYPE_RS232_422_485_2B:
> > + port->port.rs485_config = generic_rs485_config;
> > + port->port.rs485_supported = generic_rs485_supported;
> > + break;
> > + default:
> > + break;
> > + }
> > +
> > + ret = cti_port_setup_common(priv, idx, offset, port);
> > + if (ret)
> > + return ret;
> > +
> > + exar_write_reg(priv, (offset + UART_EXAR_8XMODE), 0x00);
> > + exar_write_reg(priv, (offset + UART_EXAR_FCTR), UART_FCTR_EXAR_TRGD);
> > + exar_write_reg(priv, (offset + UART_EXAR_TXTRG), 128);
> > + exar_write_reg(priv, (offset + UART_EXAR_RXTRG), 128);
> > +
> > + return 0;
> > +}
> > +
> > +static int cti_port_setup_xr17v25x(struct exar8250 *priv,
> > + struct pci_dev *pcidev,
> > + struct uart_8250_port *port,
> > + int idx)
> > +{
> > + enum cti_port_type port_type;
> > + unsigned int offset;
> > + int ret;
> > +
> > + port_type = cti_get_port_type_xr17c15x_xr17v25x(priv, idx);
> > +
> > + offset = idx * UART_EXAR_XR17V25X_PORT_OFFSET;
> > + port->port.type = PORT_XR17D15X;
> > +
> > + //xr17v25x supports fractional baudrates
> > + port->port.get_divisor = xr17v35x_get_divisor;
> > + port->port.set_divisor = xr17v35x_set_divisor;
> > + port->port.startup = xr17v35x_startup;
> > +
> > + if (CTI_PORT_TYPE_RS485(port_type)) {
> > + switch (priv->pcidev->subsystem_device) {
> > + //These cards support power on 485 tri-state via MPIO
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_485:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_SP:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_6_2_SP:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_6_SP:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_LEFT:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_RIGHT:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XP_OPTO:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_XPRS_OPTO:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_485:
> > + port->port.rs485_config = cti_rs485_config_mpio_tristate;
> > + break;
> > + //Otherwise auto or no power on 485 tri-state support
> > + default:
> > + port->port.rs485_config = generic_rs485_config;
> > + break;
> > + }
> > +
> > + port->port.rs485_supported = generic_rs485_supported;
> > + }
> > +
> > + ret = cti_port_setup_common(priv, idx, offset, port);
> > + if (ret)
> > + return ret;
> > +
> > + exar_write_reg(priv, (offset + UART_EXAR_8XMODE), 0x00);
> > + exar_write_reg(priv, (offset + UART_EXAR_FCTR), UART_FCTR_EXAR_TRGD);
> > + exar_write_reg(priv, (offset + UART_EXAR_TXTRG), 32);
> > + exar_write_reg(priv, (offset + UART_EXAR_RXTRG), 32);
> > +
> > + return 0;
> > +}
> > +
> > +static int cti_port_setup_xr17c15x(struct exar8250 *priv,
> > + struct pci_dev *pcidev,
> > + struct uart_8250_port *port,
> > + int idx)
> > +{
> > + enum cti_port_type port_type;
> > + unsigned int offset;
> > +
> > + port_type = cti_get_port_type_xr17c15x_xr17v25x(priv, idx);
> > +
> > + offset = idx * UART_EXAR_XR17C15X_PORT_OFFSET;
> > + port->port.type = PORT_XR17D15X;
> > +
> > + if (CTI_PORT_TYPE_RS485(port_type)) {
> > + switch (priv->pcidev->subsystem_device) {
> > + //These cards support power on 485 tri-state via MPIO
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_485:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_SP:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_6_2_SP:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_6_SP:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_LEFT:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_RIGHT:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XP_OPTO:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_XPRS_OPTO:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_485:
> > + port->port.rs485_config = cti_rs485_config_mpio_tristate;
> > + break;
> > + //Otherwise auto or no power on 485 tri-state support
> > + default:
> > + port->port.rs485_config = generic_rs485_config;
> > + break;
> > + }
> > +
> > + port->port.rs485_supported = generic_rs485_supported;
> > + }
> > +
> > + return cti_port_setup_common(priv, idx, offset, port);
> > +}
> > +
> > +static int cti_board_setup_xr17v35x(struct exar8250 *priv)
> > +{
> > + if (!priv)
> > + return -EINVAL;
> > +
> > + //XR17V35X use the PCIe clock rather than crystal
> > + priv->osc_freq = CTI_DEFAULT_PCIE_OSC_FREQ;
> > +
> > + return 0;
> > +}
> > +
> > +static int cti_board_setup_xr17v25x(struct exar8250 *priv)
> > +{
> > + int osc_freq;
> > +
> > + if (!priv)
> > + return -EINVAL;
> > +
> > + osc_freq = cti_read_osc_freq(priv, CTI_EE_OFF_XR17V25X_OSC_FREQ);
> > + if (osc_freq < 0) {
> > + pci_warn(priv->pcidev,
> > + "failed to read osc freq from EEPROM, using default\n");
> > + osc_freq = CTI_DEFAULT_PCI_OSC_FREQ;
> > + }
> > +
> > + priv->osc_freq = osc_freq;
> > +
> > + /* enable interupts on cards that need the "PLX fix" */
> > + switch (priv->pcidev->subsystem_device) {
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_A:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_B:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_A:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_B:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS_OPTO:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_A:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_B:
> > + cti_set_plx_int_enable(priv, true);
> > + break;
> > + default:
> > + break;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int cti_board_setup_xr17c15x(struct exar8250 *priv)
> > +{
> > + int osc_freq;
> > +
> > + if (!priv)
> > + return -EINVAL;
> > +
> > + osc_freq = cti_read_osc_freq(priv, CTI_EE_OFF_XR17C15X_OSC_FREQ);
> > + if (osc_freq <= 0) {
> > + pci_warn(priv->pcidev,
> > + "failed to read osc freq from EEPROM, using default\n");
> > + osc_freq = CTI_DEFAULT_PCI_OSC_FREQ;
> > + }
> > +
> > + priv->osc_freq = osc_freq;
> > +
> > + /* enable interrupts on cards that need the "PLX fix" */
> > + switch (priv->pcidev->subsystem_device) {
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_A:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_B:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_A:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_B:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS_OPTO:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_A:
> > + case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_B:
> > + cti_set_plx_int_enable(priv, true);
> > + break;
> > + default:
> > + break;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int cti_board_setup_fpga(struct exar8250 *priv)
> > +{
> > + int ret;
> > + uint16_t cfg_val;
> > +
> > + if (!priv)
> > + return -EINVAL;
> > +
> > + //FPGA OSC is fixed to the 33MHz PCI clock
> > + priv->osc_freq = CTI_DEFAULT_FPGA_OSC_FREQ;
> > +
> > + //Enable external interrupts in special cfg space register
> > + ret = pci_read_config_word(priv->pcidev, 0x48, &cfg_val);
> > + if (ret)
> > + return ret;
> > +
> > + cfg_val |= BIT(15);
> > +
> > + ret = pci_write_config_word(priv->pcidev, 0x48, cfg_val);
> > + if (ret)
> > + return ret;
> > +
> > + //RS485 gate needs to be enabled; otherwise RTS/CTS will not work
> > + exar_write_reg(priv, CTI_FPGA_RS485_IO_REG, 0x01);
> > +
> > + return 0;
> > }
> >
> > static int
> > @@ -985,27 +1327,6 @@ static void xr17v35x_unregister_gpio(struct uart_8250_port *port)
> > port->port.private_data = NULL;
> > }
> >
> > -static int generic_rs485_config(struct uart_port *port, struct ktermios *termios,
> > - struct serial_rs485 *rs485)
> > -{
> > - bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
> > - u8 __iomem *p = port->membase;
> > - u8 value;
> > -
> > - value = readb(p + UART_EXAR_FCTR);
> > - if (is_rs485)
> > - value |= UART_FCTR_EXAR_485;
> > - else
> > - value &= ~UART_FCTR_EXAR_485;
> > -
> > - writeb(value, p + UART_EXAR_FCTR);
> > -
> > - if (is_rs485)
> > - writeb(UART_EXAR_RS485_DLY(4), p + UART_MSR);
> > -
> > - return 0;
> > -}
> > -
> > static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termios,
> > struct serial_rs485 *rs485)
> > {
> > @@ -1044,10 +1365,6 @@ static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termio
> > return 0;
> > }
> >
> > -static const struct serial_rs485 generic_rs485_supported = {
> > - .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND,
> > -};
> > -
> > static const struct exar8250_platform exar8250_default_platform = {
> > .register_gpio = xr17v35x_register_gpio,
> > .unregister_gpio = xr17v35x_unregister_gpio,
> > @@ -1408,8 +1725,24 @@ static const struct exar8250_board pbn_fastcom335_8 = {
> > .setup = pci_fastcom335_setup,
> > };
> >
> > -static const struct exar8250_board pbn_connect = {
> > - .setup = pci_connect_tech_setup,
> > +static const struct exar8250_board pbn_cti_xr17c15x = {
> > + .board_setup = cti_board_setup_xr17c15x,
> > + .setup = cti_port_setup_xr17c15x,
> > +};
> > +
> > +static const struct exar8250_board pbn_cti_xr17v25x = {
> > + .board_setup = cti_board_setup_xr17v25x,
> > + .setup = cti_port_setup_xr17v25x,
> > +};
> > +
> > +static const struct exar8250_board pbn_cti_xr17v35x = {
> > + .board_setup = cti_board_setup_xr17v35x,
> > + .setup = cti_port_setup_xr17v35x,
> > +};
> > +
> > +static const struct exar8250_board pbn_cti_fpga = {
> > + .board_setup = cti_board_setup_fpga,
> > + .setup = cti_port_setup_fpga,
> > };
> >
> > static const struct exar8250_board pbn_exar_ibm_saturn = {
> > @@ -1456,15 +1789,27 @@ static const struct exar8250_board pbn_exar_XR17V8358 = {
> > .exit = pci_xr17v35x_exit,
> > };
> >
> > -#define CONNECT_DEVICE(devid, sdevid, bd) { \
> > - PCI_DEVICE_SUB( \
> > - PCI_VENDOR_ID_EXAR, \
> > - PCI_DEVICE_ID_EXAR_##devid, \
> > - PCI_SUBVENDOR_ID_CONNECT_TECH, \
> > - PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_##sdevid), 0, 0, \
> > - (kernel_ulong_t)&bd \
> > +//For Connect Tech cards with Exar vendor/device PCI IDs
> > +#define CTI_EXAR_DEVICE(devid, bd) { \
> > + PCI_DEVICE_SUB( \
> > + PCI_VENDOR_ID_EXAR, \
> > + PCI_DEVICE_ID_EXAR_##devid, \
> > + PCI_SUBVENDOR_ID_CONNECT_TECH, \
> > + PCI_ANY_ID), 0, 0, \
> > + (kernel_ulong_t)&bd \
> > + }
> > +
> > +//For Connect Tech cards with Connect Tech vendor/device PCI IDs (FPGA based)
> > +#define CTI_PCI_DEVICE(devid, bd) { \
> > + PCI_DEVICE_SUB( \
> > + PCI_VENDOR_ID_CONNECT_TECH, \
> > + PCI_DEVICE_ID_CONNECT_TECH_PCI_##devid, \
> > + PCI_ANY_ID, \
> > + PCI_ANY_ID), 0, 0, \
> > + (kernel_ulong_t)&bd \
> > }
> >
> > +
> > #define EXAR_DEVICE(vend, devid, bd) { PCI_DEVICE_DATA(vend, devid, &bd) }
> >
> > #define IBM_DEVICE(devid, sdevid, bd) { \
> > @@ -1494,18 +1839,21 @@ static const struct pci_device_id exar_pci_tbl[] = {
> > EXAR_DEVICE(ACCESSIO, COM_4SM, pbn_exar_XR17C15x),
> > EXAR_DEVICE(ACCESSIO, COM_8SM, pbn_exar_XR17C15x),
> >
> > - CONNECT_DEVICE(XR17C152, UART_2_232, pbn_connect),
> > - CONNECT_DEVICE(XR17C154, UART_4_232, pbn_connect),
> > - CONNECT_DEVICE(XR17C158, UART_8_232, pbn_connect),
> > - CONNECT_DEVICE(XR17C152, UART_1_1, pbn_connect),
> > - CONNECT_DEVICE(XR17C154, UART_2_2, pbn_connect),
> > - CONNECT_DEVICE(XR17C158, UART_4_4, pbn_connect),
> > - CONNECT_DEVICE(XR17C152, UART_2, pbn_connect),
> > - CONNECT_DEVICE(XR17C154, UART_4, pbn_connect),
> > - CONNECT_DEVICE(XR17C158, UART_8, pbn_connect),
> > - CONNECT_DEVICE(XR17C152, UART_2_485, pbn_connect),
> > - CONNECT_DEVICE(XR17C154, UART_4_485, pbn_connect),
> > - CONNECT_DEVICE(XR17C158, UART_8_485, pbn_connect),
> > + CTI_EXAR_DEVICE(XR17C152, pbn_cti_xr17c15x),
> > + CTI_EXAR_DEVICE(XR17C154, pbn_cti_xr17c15x),
> > + CTI_EXAR_DEVICE(XR17C158, pbn_cti_xr17c15x),
> > +
> > + CTI_EXAR_DEVICE(XR17V252, pbn_cti_xr17v25x),
> > + CTI_EXAR_DEVICE(XR17V254, pbn_cti_xr17v25x),
> > + CTI_EXAR_DEVICE(XR17V258, pbn_cti_xr17v25x),
> > +
> > + CTI_EXAR_DEVICE(XR17V352, pbn_cti_xr17v35x),
> > + CTI_EXAR_DEVICE(XR17V354, pbn_cti_xr17v35x),
> > + CTI_EXAR_DEVICE(XR17V358, pbn_cti_xr17v35x),
> > +
> > + CTI_PCI_DEVICE(XR79X_12_XIG00X, pbn_cti_fpga),
> > + CTI_PCI_DEVICE(XR79X_12_XIG01X, pbn_cti_fpga),
> > + CTI_PCI_DEVICE(XR79X_16, pbn_cti_fpga),
> >
> > IBM_DEVICE(XR17C152, SATURN_SERIAL_ONE_PORT, pbn_exar_ibm_saturn),
> >
> > --
> > 2.43.2
> >
> >
