From: Parker Newman <pnewman@xxxxxxxxxxxxxxx>
- Removed old port setup function and replaced with UART specific ones
- Added board setup functions for CTI boards
- Replaced CONNECT_DEVICE macro with CTI_EXAR_DEVICE and CTI_PCI_DEVICE
- Moved "generic rs485" support up in the file
Signed-off-by: Parker Newman <pnewman@xxxxxxxxxxxxxxx>
---
drivers/tty/serial/8250/8250_exar.c | 454 ++++++++++++++++++++++++----
1 file changed, 401 insertions(+), 53 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index 6f3697e34722..d8425113a9f1 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -440,6 +440,31 @@ static int exar_mpio_set(struct exar8250 *priv,
return 0;
}
+static int generic_rs485_config(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485)
+{
+ bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
+ u8 __iomem *p = port->membase;
+ u8 value;
+
+ value = readb(p + UART_EXAR_FCTR);
+ if (is_rs485)
+ value |= UART_FCTR_EXAR_485;
+ else
+ value &= ~UART_FCTR_EXAR_485;
+
+ writeb(value, p + UART_EXAR_FCTR);
+
+ if (is_rs485)
+ writeb(UART_EXAR_RS485_DLY(4), p + UART_MSR);
+
+ return 0;
+}
+
+static const struct serial_rs485 generic_rs485_supported = {
+ .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND,
+};
+
static void exar_pm(struct uart_port *port, unsigned int state, unsigned int old)
{
/*
@@ -875,15 +900,332 @@ static enum cti_port_type cti_get_port_type_xr17v35x(struct exar8250 *priv,
return port_type;
}
-static int
-pci_connect_tech_setup(struct exar8250 *priv, struct pci_dev *pcidev,
- struct uart_8250_port *port, int idx)
+static int cti_rs485_config_mpio_tristate(struct uart_port *port,
+ struct ktermios *termios,
+ struct serial_rs485 *rs485)
{
- unsigned int offset = idx * 0x200;
- unsigned int baud = 1843200;
+ struct exar8250 *priv;
+ int ret;
- port->port.uartclk = baud * 16;
- return default_setup(priv, pcidev, idx, offset, port);
+ priv = (struct exar8250 *)port->private_data;
+ if (!priv)
+ return -EINVAL;
+
+ ret = generic_rs485_config(port, termios, rs485);
+ if (ret)
+ return ret;
+
+ //disable power-on tri-state via MPIO
+ return cti_set_tristate(priv, port->port_id, false);
+}
+
+static int cti_port_setup_common(struct exar8250 *priv,
+ int idx, unsigned int offset,
+ struct uart_8250_port *port)
+{
+ int ret;
+
+ if (!priv || !port)
+ return -EINVAL;
+
+ if (priv->osc_freq == 0)
+ return -EINVAL;
+
+ port->port.port_id = idx;
+ port->port.uartclk = priv->osc_freq;
+
+ ret = serial8250_pci_setup_port(priv->pcidev, port, 0, offset, 0);
+ if (ret) {
+ pci_err(priv->pcidev,
+ "failed to setup pci for port %d err: %d\n", idx, ret);
+ return ret;
+ }
+
+ port->port.private_data = (void *)priv;
+ port->port.pm = exar_pm;
+ port->port.shutdown = exar_shutdown;
+
+ return 0;
+}
+
+static int cti_port_setup_fpga(struct exar8250 *priv,
+ struct pci_dev *pcidev,
+ struct uart_8250_port *port,
+ int idx)
+{
+ enum cti_port_type port_type;
+ unsigned int offset;
+
+ port_type = cti_get_port_type_fpga(priv, idx);
+
+ //FPGA shares port offests with XR17C15X
+ offset = idx * UART_EXAR_XR17C15X_PORT_OFFSET;
+ port->port.type = PORT_XR17D15X;
+
+ port->port.get_divisor = xr17v35x_get_divisor;
+ port->port.set_divisor = xr17v35x_set_divisor;
+ port->port.startup = xr17v35x_startup;
+
+ if (CTI_PORT_TYPE_RS485(port_type)) {
+ port->port.rs485_config = generic_rs485_config;
+ port->port.rs485_supported = generic_rs485_supported;
+ }
+
+ return cti_port_setup_common(priv, idx, offset, port);
+}
+
+static int cti_port_setup_xr17v35x(struct exar8250 *priv,
+ struct pci_dev *pcidev,
+ struct uart_8250_port *port,
+ int idx)
+{
+ enum cti_port_type port_type;
+ unsigned int offset;
+ int ret;
+
+ port_type = cti_get_port_type_xr17v35x(priv, idx);
+
+ offset = idx * UART_EXAR_XR17V35X_PORT_OFFSET;
+ port->port.type = PORT_XR17V35X;
+
+ port->port.get_divisor = xr17v35x_get_divisor;
+ port->port.set_divisor = xr17v35x_set_divisor;
+ port->port.startup = xr17v35x_startup;
+
+ switch (port_type) {
+ case CTI_PORT_TYPE_RS422_485:
+ case CTI_PORT_TYPE_RS232_422_485_HW:
+ port->port.rs485_config = cti_rs485_config_mpio_tristate;
+ port->port.rs485_supported = generic_rs485_supported;
+ break;
+ case CTI_PORT_TYPE_RS232_422_485_SW:
+ case CTI_PORT_TYPE_RS232_422_485_4B:
+ case CTI_PORT_TYPE_RS232_422_485_2B:
+ port->port.rs485_config = generic_rs485_config;
+ port->port.rs485_supported = generic_rs485_supported;
+ break;
+ default:
+ break;
+ }
+
+ ret = cti_port_setup_common(priv, idx, offset, port);
+ if (ret)
+ return ret;
+
+ exar_write_reg(priv, (offset + UART_EXAR_8XMODE), 0x00);
+ exar_write_reg(priv, (offset + UART_EXAR_FCTR), UART_FCTR_EXAR_TRGD);
+ exar_write_reg(priv, (offset + UART_EXAR_TXTRG), 128);
+ exar_write_reg(priv, (offset + UART_EXAR_RXTRG), 128);
+
+ return 0;
+}
+
+static int cti_port_setup_xr17v25x(struct exar8250 *priv,
+ struct pci_dev *pcidev,
+ struct uart_8250_port *port,
+ int idx)
+{
+ enum cti_port_type port_type;
+ unsigned int offset;
+ int ret;
+
+ port_type = cti_get_port_type_xr17c15x_xr17v25x(priv, idx);
+
+ offset = idx * UART_EXAR_XR17V25X_PORT_OFFSET;
+ port->port.type = PORT_XR17D15X;
+
+ //xr17v25x supports fractional baudrates
+ port->port.get_divisor = xr17v35x_get_divisor;
+ port->port.set_divisor = xr17v35x_set_divisor;
+ port->port.startup = xr17v35x_startup;
+
+ if (CTI_PORT_TYPE_RS485(port_type)) {
+ switch (priv->pcidev->subsystem_device) {
+ //These cards support power on 485 tri-state via MPIO
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_485:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_SP:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_6_2_SP:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_6_SP:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_LEFT:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_RIGHT:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XP_OPTO:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_XPRS_OPTO:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_485:
+ port->port.rs485_config = cti_rs485_config_mpio_tristate;
+ break;
+ //Otherwise auto or no power on 485 tri-state support
+ default:
+ port->port.rs485_config = generic_rs485_config;
+ break;
+ }
+
+ port->port.rs485_supported = generic_rs485_supported;
+ }
+
+ ret = cti_port_setup_common(priv, idx, offset, port);
+ if (ret)
+ return ret;
+
+ exar_write_reg(priv, (offset + UART_EXAR_8XMODE), 0x00);
+ exar_write_reg(priv, (offset + UART_EXAR_FCTR), UART_FCTR_EXAR_TRGD);
+ exar_write_reg(priv, (offset + UART_EXAR_TXTRG), 32);
+ exar_write_reg(priv, (offset + UART_EXAR_RXTRG), 32);
+
+ return 0;
+}
+
+static int cti_port_setup_xr17c15x(struct exar8250 *priv,
+ struct pci_dev *pcidev,
+ struct uart_8250_port *port,
+ int idx)
+{
+ enum cti_port_type port_type;
+ unsigned int offset;
+
+ port_type = cti_get_port_type_xr17c15x_xr17v25x(priv, idx);
+
+ offset = idx * UART_EXAR_XR17C15X_PORT_OFFSET;
+ port->port.type = PORT_XR17D15X;
+
+ if (CTI_PORT_TYPE_RS485(port_type)) {
+ switch (priv->pcidev->subsystem_device) {
+ //These cards support power on 485 tri-state via MPIO
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_485:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_SP:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_6_2_SP:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_6_SP:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_LEFT:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_RIGHT:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XP_OPTO:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_XPRS_OPTO:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_485:
+ port->port.rs485_config = cti_rs485_config_mpio_tristate;
+ break;
+ //Otherwise auto or no power on 485 tri-state support
+ default:
+ port->port.rs485_config = generic_rs485_config;
+ break;
+ }
+
+ port->port.rs485_supported = generic_rs485_supported;
+ }
+
+ return cti_port_setup_common(priv, idx, offset, port);
+}
+
+static int cti_board_setup_xr17v35x(struct exar8250 *priv)
+{
+ if (!priv)
+ return -EINVAL;
+
+ //XR17V35X use the PCIe clock rather than crystal
+ priv->osc_freq = CTI_DEFAULT_PCIE_OSC_FREQ;
+
+ return 0;
+}
+
+static int cti_board_setup_xr17v25x(struct exar8250 *priv)
+{
+ int osc_freq;
+
+ if (!priv)
+ return -EINVAL;
+
+ osc_freq = cti_read_osc_freq(priv, CTI_EE_OFF_XR17V25X_OSC_FREQ);
+ if (osc_freq < 0) {
+ pci_warn(priv->pcidev,
+ "failed to read osc freq from EEPROM, using default\n");
+ osc_freq = CTI_DEFAULT_PCI_OSC_FREQ;
+ }
+
+ priv->osc_freq = osc_freq;
+
+ /* enable interupts on cards that need the "PLX fix" */
+ switch (priv->pcidev->subsystem_device) {
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_A:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_B:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_A:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_B:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS_OPTO:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_A:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_B:
+ cti_set_plx_int_enable(priv, true);
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+static int cti_board_setup_xr17c15x(struct exar8250 *priv)
+{
+ int osc_freq;
+
+ if (!priv)
+ return -EINVAL;
+
+ osc_freq = cti_read_osc_freq(priv, CTI_EE_OFF_XR17C15X_OSC_FREQ);
+ if (osc_freq <= 0) {
+ pci_warn(priv->pcidev,
+ "failed to read osc freq from EEPROM, using default\n");
+ osc_freq = CTI_DEFAULT_PCI_OSC_FREQ;
+ }
+
+ priv->osc_freq = osc_freq;
+
+ /* enable interrupts on cards that need the "PLX fix" */
+ switch (priv->pcidev->subsystem_device) {
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_A:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_B:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_A:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_B:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS_OPTO:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_A:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_B:
+ cti_set_plx_int_enable(priv, true);
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+static int cti_board_setup_fpga(struct exar8250 *priv)
+{
+ int ret;
+ uint16_t cfg_val;
+
+ if (!priv)
+ return -EINVAL;
+
+ //FPGA OSC is fixed to the 33MHz PCI clock
+ priv->osc_freq = CTI_DEFAULT_FPGA_OSC_FREQ;
+
+ //Enable external interrupts in special cfg space register
+ ret = pci_read_config_word(priv->pcidev, 0x48, &cfg_val);
+ if (ret)
+ return ret;
+
+ cfg_val |= BIT(15);
+
+ ret = pci_write_config_word(priv->pcidev, 0x48, cfg_val);
+ if (ret)
+ return ret;
+
+ //RS485 gate needs to be enabled; otherwise RTS/CTS will not work
+ exar_write_reg(priv, CTI_FPGA_RS485_IO_REG, 0x01);
+
+ return 0;
}
static int
@@ -985,27 +1327,6 @@ static void xr17v35x_unregister_gpio(struct uart_8250_port *port)
port->port.private_data = NULL;
}
-static int generic_rs485_config(struct uart_port *port, struct ktermios *termios,
- struct serial_rs485 *rs485)
-{
- bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
- u8 __iomem *p = port->membase;
- u8 value;
-
- value = readb(p + UART_EXAR_FCTR);
- if (is_rs485)
- value |= UART_FCTR_EXAR_485;
- else
- value &= ~UART_FCTR_EXAR_485;
-
- writeb(value, p + UART_EXAR_FCTR);
-
- if (is_rs485)
- writeb(UART_EXAR_RS485_DLY(4), p + UART_MSR);
-
- return 0;
-}
-
static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termios,
struct serial_rs485 *rs485)
{
@@ -1044,10 +1365,6 @@ static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termio
return 0;
}
-static const struct serial_rs485 generic_rs485_supported = {
- .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND,
-};
-
static const struct exar8250_platform exar8250_default_platform = {
.register_gpio = xr17v35x_register_gpio,
.unregister_gpio = xr17v35x_unregister_gpio,
@@ -1408,8 +1725,24 @@ static const struct exar8250_board pbn_fastcom335_8 = {
.setup = pci_fastcom335_setup,
};
-static const struct exar8250_board pbn_connect = {
- .setup = pci_connect_tech_setup,
+static const struct exar8250_board pbn_cti_xr17c15x = {
+ .board_setup = cti_board_setup_xr17c15x,
+ .setup = cti_port_setup_xr17c15x,
+};
+
+static const struct exar8250_board pbn_cti_xr17v25x = {
+ .board_setup = cti_board_setup_xr17v25x,
+ .setup = cti_port_setup_xr17v25x,
+};
+
+static const struct exar8250_board pbn_cti_xr17v35x = {
+ .board_setup = cti_board_setup_xr17v35x,
+ .setup = cti_port_setup_xr17v35x,
+};
+
+static const struct exar8250_board pbn_cti_fpga = {
+ .board_setup = cti_board_setup_fpga,
+ .setup = cti_port_setup_fpga,
};
static const struct exar8250_board pbn_exar_ibm_saturn = {
@@ -1456,15 +1789,27 @@ static const struct exar8250_board pbn_exar_XR17V8358 = {
.exit = pci_xr17v35x_exit,
};
-#define CONNECT_DEVICE(devid, sdevid, bd) { \
- PCI_DEVICE_SUB( \
- PCI_VENDOR_ID_EXAR, \
- PCI_DEVICE_ID_EXAR_##devid, \
- PCI_SUBVENDOR_ID_CONNECT_TECH, \
- PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_##sdevid), 0, 0, \
- (kernel_ulong_t)&bd \
+//For Connect Tech cards with Exar vendor/device PCI IDs
+#define CTI_EXAR_DEVICE(devid, bd) { \
+ PCI_DEVICE_SUB( \
+ PCI_VENDOR_ID_EXAR, \
+ PCI_DEVICE_ID_EXAR_##devid, \
+ PCI_SUBVENDOR_ID_CONNECT_TECH, \
+ PCI_ANY_ID), 0, 0, \
+ (kernel_ulong_t)&bd \
+ }
+
+//For Connect Tech cards with Connect Tech vendor/device PCI IDs (FPGA based)
+#define CTI_PCI_DEVICE(devid, bd) { \
+ PCI_DEVICE_SUB( \
+ PCI_VENDOR_ID_CONNECT_TECH, \
+ PCI_DEVICE_ID_CONNECT_TECH_PCI_##devid, \
+ PCI_ANY_ID, \
+ PCI_ANY_ID), 0, 0, \
+ (kernel_ulong_t)&bd \
}
+
#define EXAR_DEVICE(vend, devid, bd) { PCI_DEVICE_DATA(vend, devid, &bd) }
#define IBM_DEVICE(devid, sdevid, bd) { \
@@ -1494,18 +1839,21 @@ static const struct pci_device_id exar_pci_tbl[] = {
EXAR_DEVICE(ACCESSIO, COM_4SM, pbn_exar_XR17C15x),
EXAR_DEVICE(ACCESSIO, COM_8SM, pbn_exar_XR17C15x),
- CONNECT_DEVICE(XR17C152, UART_2_232, pbn_connect),
- CONNECT_DEVICE(XR17C154, UART_4_232, pbn_connect),
- CONNECT_DEVICE(XR17C158, UART_8_232, pbn_connect),
- CONNECT_DEVICE(XR17C152, UART_1_1, pbn_connect),
- CONNECT_DEVICE(XR17C154, UART_2_2, pbn_connect),
- CONNECT_DEVICE(XR17C158, UART_4_4, pbn_connect),
- CONNECT_DEVICE(XR17C152, UART_2, pbn_connect),
- CONNECT_DEVICE(XR17C154, UART_4, pbn_connect),
- CONNECT_DEVICE(XR17C158, UART_8, pbn_connect),
- CONNECT_DEVICE(XR17C152, UART_2_485, pbn_connect),
- CONNECT_DEVICE(XR17C154, UART_4_485, pbn_connect),
- CONNECT_DEVICE(XR17C158, UART_8_485, pbn_connect),
+ CTI_EXAR_DEVICE(XR17C152, pbn_cti_xr17c15x),
+ CTI_EXAR_DEVICE(XR17C154, pbn_cti_xr17c15x),
+ CTI_EXAR_DEVICE(XR17C158, pbn_cti_xr17c15x),
+
+ CTI_EXAR_DEVICE(XR17V252, pbn_cti_xr17v25x),
+ CTI_EXAR_DEVICE(XR17V254, pbn_cti_xr17v25x),
+ CTI_EXAR_DEVICE(XR17V258, pbn_cti_xr17v25x),
+
+ CTI_EXAR_DEVICE(XR17V352, pbn_cti_xr17v35x),
+ CTI_EXAR_DEVICE(XR17V354, pbn_cti_xr17v35x),
+ CTI_EXAR_DEVICE(XR17V358, pbn_cti_xr17v35x),
+
+ CTI_PCI_DEVICE(XR79X_12_XIG00X, pbn_cti_fpga),
+ CTI_PCI_DEVICE(XR79X_12_XIG01X, pbn_cti_fpga),
+ CTI_PCI_DEVICE(XR79X_16, pbn_cti_fpga),
IBM_DEVICE(XR17C152, SATURN_SERIAL_ONE_PORT, pbn_exar_ibm_saturn),
--
2.43.2
