From: Parker Newman <pnewman@xxxxxxxxxxxxxxx>
- Adds various helper functions for CTI boards.
- Add osc_freq and pcidev to struct exar8250
- Added a exar_get_nr_ports function
Signed-off-by: Parker Newman <pnewman@xxxxxxxxxxxxxxx>
---
drivers/tty/serial/8250/8250_exar.c | 363 +++++++++++++++++++++++++++-
1 file changed, 357 insertions(+), 6 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index b30f3855652a..6f3697e34722 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -137,6 +137,9 @@
#define UART_EXAR_REGB_EE_ADDR_SIZE 6
#define UART_EXAR_REGB_EE_DATA_SIZE 16
+#define UART_EXAR_XR17C15X_PORT_OFFSET 0x200
+#define UART_EXAR_XR17V25X_PORT_OFFSET 0x200
+#define UART_EXAR_XR17V35X_PORT_OFFSET 0x400
/*
* IOT2040 MPIO wiring semantics:
@@ -173,6 +176,46 @@
#define IOT2040_UARTS_ENABLE 0x03
#define IOT2040_UARTS_GPIO_HI_MODE 0xF8 /* enable & LED as outputs */
+/* CTI EEPROM offsets */
+#define CTI_EE_OFF_XR17C15X_OSC_FREQ 0x04 /* 2 words (4 bytes) */
+#define CTI_EE_OFF_XR17V25X_OSC_FREQ 0x08 /* 2 words (4 bytes) */
+#define CTI_EE_OFF_XR17C15X_PART_NUM 0x0A /* 4 words (8 bytes) */
+#define CTI_EE_OFF_XR17V25X_PART_NUM 0x0E /* 4 words (8 bytes) */
+#define CTI_EE_OFF_XR17C15X_SERIAL_NUM 0x0E /* 1 word (2 bytes) */
+#define CTI_EE_OFF_XR17V25X_SERIAL_NUM 0x12 /* 1 word (2 bytes) */
+#define CTI_EE_OFF_XR17V35X_SERIAL_NUM 0x11 /* 2 word (4 bytes) */
+#define CTI_EE_OFF_XR17V35X_BOARD_FLAGS 0x13 /* 1 word (2 bytes) */
+#define CTI_EE_OFF_XR17V35X_PORT_FLAGS 0x14 /* 1 word (per port) */
+
+#define CTI_FPGA_RS485_IO_REG 0x2008
+
+#define CTI_DEFAULT_PCI_OSC_FREQ 29491200
+#define CTI_DEFAULT_PCIE_OSC_FREQ 125000000
+#define CTI_DEFAULT_FPGA_OSC_FREQ 33333333
+
+/*
+ * CTI Serial port line types. These match the values stored in the first
+ * nibble of the CTI EEPROM port_flags word.
+ */
+enum cti_port_type {
+ CTI_PORT_TYPE_NONE = 0,
+ CTI_PORT_TYPE_RS232, //RS232 ONLY
+ CTI_PORT_TYPE_RS422_485, //RS422/RS485 ONLY
+ CTI_PORT_TYPE_RS232_422_485_HW, //RS232/422/485 HW ONLY Switchable
+ CTI_PORT_TYPE_RS232_422_485_SW, //RS232/422/485 SW ONLY Switchable
+ CTI_PORT_TYPE_RS232_422_485_4B, //RS232/422/485 HW/SW (4bit ex. BCG004)
+ CTI_PORT_TYPE_RS232_422_485_2B, //RS232/422/485 HW/SW (2bit ex. BBG008)
+ CTI_PORT_TYPE_MAX,
+};
+
+#define CTI_PORT_TYPE_VALID(_port_type) \
+ (((_port_type) > CTI_PORT_TYPE_NONE) && \
+ ((_port_type) < CTI_PORT_TYPE_MAX))
+
+#define CTI_PORT_TYPE_RS485(_port_type) \
+ (((_port_type) > CTI_PORT_TYPE_RS232) && \
+ ((_port_type) < CTI_PORT_TYPE_MAX))
+
struct exar8250;
struct exar8250_platform {
@@ -202,6 +245,8 @@ struct exar8250_board {
struct exar8250 {
unsigned int nr;
+ unsigned int osc_freq;
+ struct pci_dev *pcidev;
struct exar8250_board *board;
void __iomem *virt;
int line[];
@@ -557,6 +602,279 @@ pci_fastcom335_setup(struct exar8250 *priv, struct pci_dev *pcidev,
return 0;
}
+/**
+ * cti_set_tristate() - Enable/Disable RS485 transciever tristate
+ * @priv: Device's private structure
+ * @port_num: Port number to set tristate on/off
+ * @enable: Enable tristate if true, disable if false
+ *
+ * Most RS485 capable cards have a power on tristate jumper/switch that ensures
+ * the RS422/RS485 transciever does not drive a multi-drop RS485 bus when it is
+ * not the master. When this jumper is installed the user must set the RS485
+ * mode to disable tristate prior to using the port.
+ *
+ * Some Exar UARTs have an auto-tristate feature while others require setting
+ * an MPIO to disable the tristate.
+ *
+ * Return: 0 on success, negative error code on failure
+ */
+static int cti_set_tristate(struct exar8250 *priv,
+ unsigned int port_num, bool enable)
+{
+ int ret = 0;
+
+ if (!priv || (port_num >= priv->nr))
+ return -EINVAL;
+
+ //Only Exar based cards use MPIO, return 0 otherwise
+ if (priv->pcidev->vendor != PCI_VENDOR_ID_EXAR)
+ return 0;
+
+ pci_dbg(priv->pcidev, "%s tristate for port %u\n",
+ (enable ? "enabling" : "disabling"), port_num);
+
+ ret = exar_mpio_set(priv, port_num, !enable);
+ if (ret)
+ return ret;
+
+ //ensure MPIO is an output
+ ret = exar_mpio_config(priv, port_num, true);
+
+ return ret;
+}
+
+/**
+ * cti_set_plx_int_enable() - Enable/Disable PCI interrupts
+ * @priv: Device's private structure
+ * @enable: Enable interrupts if true, disable if false
+ *
+ * Some older CTI cards require MPIO_0 to be set low to enable the PCI
+ * interupts from the UART to the PLX PCI->PCIe bridge.
+ *
+ * Return: 0 on success, negative error code on failure
+ */
+static int cti_set_plx_int_enable(struct exar8250 *priv, bool enable)
+{
+ int ret = 0;
+
+ if (!priv)
+ return -EINVAL;
+
+ //Only Exar based cards use MPIO, return 0 otherwise
+ if (priv->pcidev->vendor != PCI_VENDOR_ID_EXAR)
+ return 0;
+
+ pci_dbg(priv->pcidev, "%s plx fix\n",
+ (enable ? "enabling" : "disabling"));
+
+ //INT enabled when MPIO0 is LOW
+ ret = exar_mpio_set(priv, 0, !enable);
+ if (ret)
+ return ret;
+
+ //ensure MPIO is an output
+ ret = exar_mpio_config(priv, 0, true);
+
+ return ret;
+}
+
+/**
+ * cti_read_osc_freq() - Read the UART oscillator frequency from EEPROM
+ * @priv: Device's private structure
+ *
+ * CTI XR17x15X and XR17V25X cards have the serial boards oscillator frequency
+ * stored in the EEPROM. FPGA and XR17V35X based cards use the PCI/PCIe clock.
+ *
+ * Return: frequency on success, negative error code on failure
+ */
+static int cti_read_osc_freq(struct exar8250 *priv, uint8_t eeprom_offset)
+{
+ int osc_freq;
+
+ if (!priv)
+ return -EINVAL;
+
+ osc_freq = (exar_ee_read(priv, eeprom_offset));
+ osc_freq |= (exar_ee_read(priv, (eeprom_offset + 1)) << 16);
+
+ //check if EEPROM word was blank
+ if ((osc_freq == 0xFFFF) || (osc_freq == 0x0000))
+ return -EIO;
+
+ pci_dbg(priv->pcidev, "osc_freq from EEPROM %d\n", osc_freq);
+
+ return osc_freq;
+}
+
+/**
+ * cti_get_port_type_xr17c15x_xr17v25x() - Get the port type of a xr17c15x
+ * or xr17v25x card
+ *
+ * @priv: Device's private structure
+ * @port_num: Port to get type of
+ *
+ * CTI xr17c15x and xr17v25x based cards port types are based on PCI IDs
+ *
+ * Return: port type on success, CTI_PORT_TYPE_NONE on failure
+ */
+static enum cti_port_type cti_get_port_type_xr17c15x_xr17v25x(struct exar8250 *priv,
+ unsigned int port_num)
+{
+ enum cti_port_type port_type;
+
+ if (!priv)
+ return CTI_PORT_TYPE_NONE;
+
+ switch (priv->pcidev->subsystem_device) {
+ //RS232 only cards
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_232:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_232:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_232:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_232:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_232_NS:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_232:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_232_NS:
+ port_type = CTI_PORT_TYPE_RS232;
+ break;
+ //1x RS232, 1x RS422/RS485
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_1_1:
+ port_type = (port_num == 0) ?
+ CTI_PORT_TYPE_RS232 : CTI_PORT_TYPE_RS422_485;
+ break;
+ //2x RS232, 2x RS422/RS485
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_2:
+ port_type = (port_num < 2) ?
+ CTI_PORT_TYPE_RS232 : CTI_PORT_TYPE_RS422_485;
+ break;
+ //4x RS232, 4x RS422/RS485
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_SP:
+ port_type = (port_num < 4) ?
+ CTI_PORT_TYPE_RS232 : CTI_PORT_TYPE_RS422_485;
+ break;
+ //RS232/RS422/RS485 HW (jumper) selectable
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_SP_OPTO:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_SP_OPTO_A:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_SP_OPTO_B:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_A:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_B:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_A:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_16_XPRS_B:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XPRS_OPTO:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_A:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XPRS_OPTO_B:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_LEFT:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_XP_OPTO_RIGHT:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_XP_OPTO:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4_XPRS_OPTO:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP:
+ port_type = CTI_PORT_TYPE_RS232_422_485_HW;
+ break;
+ //RS422/RS485 HW (jumper) selectable
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_485:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_485:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_485:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_SP_485:
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_XPRS_LP_485:
+ port_type = CTI_PORT_TYPE_RS422_485;
+ break;
+ //6x RS232, 2x RS422/RS485
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_6_2_SP:
+ port_type = (port_num < 6) ?
+ CTI_PORT_TYPE_RS232 : CTI_PORT_TYPE_RS422_485;
+ break;
+ //2x RS232, 6x RS422/RS485
+ case PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_6_SP:
+ port_type = (port_num < 2) ?
+ CTI_PORT_TYPE_RS232 : CTI_PORT_TYPE_RS422_485;
+ break;
+ default:
+ pci_err(priv->pcidev, "unknown/unsupported device\n");
+ port_type = CTI_PORT_TYPE_NONE;
+ }
+
+ return port_type;
+}
+
+/**
+ * cti_get_port_type_fpga() - Get the port type of a CTI FPGA card
+ * @priv: Device's private structure
+ * @port_num: Port to get type of
+ *
+ * FPGA based cards port types are based on PCI IDs
+ *
+ * Return: port type on success, CTI_PORT_TYPE_NONE on failure
+ */
+static enum cti_port_type cti_get_port_type_fpga(struct exar8250 *priv,
+ unsigned int port_num)
+{
+ enum cti_port_type port_type;
+
+ if (!priv)
+ return CTI_PORT_TYPE_NONE;
+
+ switch (priv->pcidev->device) {
+ case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_12_XIG00X:
+ case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_12_XIG01X:
+ case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_16:
+ port_type = CTI_PORT_TYPE_RS232_422_485_HW;
+ break;
+ default:
+ pci_err(priv->pcidev, "unknown/unsupported device\n");
+ return CTI_PORT_TYPE_NONE;
+ }
+
+ return port_type;
+}
+
+/**
+ * cti_get_port_type_xr17v35x() - Read port type from the EEPROM
+ * @priv: Device's private structure
+ * @port_num: port offset
+ *
+ * CTI XR17V35X based cards have the port types stored in the EEPROM.
+ * This function reads the port type for a single port.
+ *
+ * Return: port type on success, CTI_PORT_TYPE_NONE on failure
+ */
+static enum cti_port_type cti_get_port_type_xr17v35x(struct exar8250 *priv,
+ unsigned int port_num)
+{
+ uint16_t port_flags;
+ uint8_t offset;
+ enum cti_port_type port_type;
+
+ if (!priv)
+ return CTI_PORT_TYPE_NONE;
+
+ offset = CTI_EE_OFF_XR17V35X_PORT_FLAGS + port_num;
+ port_flags = exar_ee_read(priv, offset);
+
+ port_type = (port_flags & 0x00FF);
+
+ if (!CTI_PORT_TYPE_VALID(port_type)) {
+ /*
+ * If the port type is missing the card assume it is a
+ * RS232/RS422/RS485 card to be safe.
+ *
+ * There is one known board (BEG013) that only has
+ * 3 of 4 port types written to the EEPROM so this
+ * acts as a work around.
+ */
+ pci_warn(priv->pcidev,
+ "failed to get port %d type from EEPROM\n", port_num);
+ port_type = CTI_PORT_TYPE_RS232_422_485_HW;
+ }
+
+ return port_type;
+}
+
static int
pci_connect_tech_setup(struct exar8250 *priv, struct pci_dev *pcidev,
struct uart_8250_port *port, int idx)
@@ -914,6 +1232,39 @@ static irqreturn_t exar_misc_handler(int irq, void *data)
return IRQ_HANDLED;
}
+static unsigned int exar_get_nr_ports(struct exar8250_board *board,
+ struct pci_dev *pcidev)
+{
+ unsigned int nr_ports = 0;
+
+ if (!board || !pcidev)
+ return 0;
+
+ if (pcidev->vendor == PCI_VENDOR_ID_ACCESSIO) {
+ nr_ports = BIT(((pcidev->device & 0x38) >> 3) - 1);
+ } else if (board->num_ports > 0) {
+ //Check if board struct overrides number of ports
+ nr_ports = board->num_ports;
+ } else if (pcidev->vendor == PCI_VENDOR_ID_EXAR) {
+ //Exar encodes # ports in last nibble of PCI Device ID ex. 0358
+ nr_ports = pcidev->device & 0x0f;
+ } else if (pcidev->vendor == PCI_VENDOR_ID_CONNECT_TECH) {
+ //Handle CTI FPGA cards
+ switch (pcidev->device) {
+ case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_12_XIG00X:
+ case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_12_XIG01X:
+ nr_ports = 12;
+ break;
+ case PCI_DEVICE_ID_CONNECT_TECH_PCI_XR79X_16:
+ nr_ports = 16;
+ default:
+ break;
+ }
+ }
+
+ return nr_ports;
+}
+
static int
exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent)
{
@@ -933,18 +1284,18 @@ exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent)
maxnr = pci_resource_len(pcidev, bar) >> (board->reg_shift + 3);
- if (pcidev->vendor == PCI_VENDOR_ID_ACCESSIO)
- nr_ports = BIT(((pcidev->device & 0x38) >> 3) - 1);
- else if (board->num_ports)
- nr_ports = board->num_ports;
- else
- nr_ports = pcidev->device & 0x0f;
+ nr_ports = exar_get_nr_ports(board, pcidev);
+ if (nr_ports == 0) {
+ pci_err(pcidev, "failed to get number of ports\n");
+ return -ENODEV;
+ }
priv = devm_kzalloc(&pcidev->dev, struct_size(priv, line, nr_ports), GFP_KERNEL);
if (!priv)
return -ENOMEM;
priv->board = board;
+ priv->pcidev = pcidev;
priv->virt = pcim_iomap(pcidev, bar, 0);
if (!priv->virt)
return -ENOMEM;
--
2.43.2
