On Wed, 9 Nov 2022, Sherry Sun wrote: > For the lpuart driver, the Idle Line Interrupt Enable now is only needed > for the CPU mode, so enable the UARTCTRL_ILIE at the correct place, and > clear it when shutdown. > > Also need to configure the suitable UARTCTRL_IDLECFG, now the value is > 0x7, represent 128 idle characters will trigger the Idle Line Interrupt. > > Signed-off-by: Sherry Sun <sherry.sun@xxxxxxx> > --- > drivers/tty/serial/fsl_lpuart.c | 13 ++++++++----- > 1 file changed, 8 insertions(+), 5 deletions(-) > > diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c > index bd685491eead..f5a0a14fa366 100644 > --- a/drivers/tty/serial/fsl_lpuart.c > +++ b/drivers/tty/serial/fsl_lpuart.c > @@ -179,7 +179,7 @@ > #define UARTCTRL_SBK 0x00010000 > #define UARTCTRL_MA1IE 0x00008000 > #define UARTCTRL_MA2IE 0x00004000 > -#define UARTCTRL_IDLECFG 0x00000100 > +#define UARTCTRL_IDLECFG_OFF 8 > #define UARTCTRL_LOOPS 0x00000080 > #define UARTCTRL_DOZEEN 0x00000040 > #define UARTCTRL_RSRC 0x00000020 > @@ -230,6 +230,8 @@ > #define GLOBAL_RST_MIN_US 20 > #define GLOBAL_RST_MAX_US 40 > > +#define UARTCTRL_IDLECFG 0x7 > + GEN_MASK() to the correct bits directly? > /* Rx DMA timeout in ms, which is used to calculate Rx ring buffer size */ > #define DMA_RX_TIMEOUT (10) > > @@ -1506,7 +1508,7 @@ static void lpuart32_setup_watermark(struct lpuart_port *sport) > ctrl = lpuart32_read(&sport->port, UARTCTRL); > ctrl_saved = ctrl; > ctrl &= ~(UARTCTRL_TIE | UARTCTRL_TCIE | UARTCTRL_TE | > - UARTCTRL_RIE | UARTCTRL_RE); > + UARTCTRL_RIE | UARTCTRL_RE | UARTCTRL_ILIE); > lpuart32_write(&sport->port, ctrl, UARTCTRL); > > /* enable FIFO mode */ > @@ -1530,7 +1532,8 @@ static void lpuart32_setup_watermark_enable(struct lpuart_port *sport) > lpuart32_setup_watermark(sport); > > temp = lpuart32_read(&sport->port, UARTCTRL); > - temp |= UARTCTRL_RE | UARTCTRL_TE | UARTCTRL_ILIE; > + temp |= UARTCTRL_RE | UARTCTRL_TE; > + temp |= UARTCTRL_IDLECFG << UARTCTRL_IDLECFG_OFF; FIELD_PREP() would probably be more appropriate for this? Then you can also drop the shift offset. -- i. > lpuart32_write(&sport->port, temp, UARTCTRL); > } > > @@ -1669,7 +1672,7 @@ static void lpuart32_configure(struct lpuart_port *sport) > } > temp = lpuart32_read(&sport->port, UARTCTRL); > if (!sport->lpuart_dma_rx_use) > - temp |= UARTCTRL_RIE; > + temp |= UARTCTRL_RIE | UARTCTRL_ILIE; > if (!sport->lpuart_dma_tx_use) > temp |= UARTCTRL_TIE; > lpuart32_write(&sport->port, temp, UARTCTRL); > @@ -1770,7 +1773,7 @@ static void lpuart32_shutdown(struct uart_port *port) > > /* disable Rx/Tx and interrupts */ > temp = lpuart32_read(port, UARTCTRL); > - temp &= ~(UARTCTRL_TE | UARTCTRL_RE | > + temp &= ~(UARTCTRL_TE | UARTCTRL_RE | UARTCTRL_ILIE | > UARTCTRL_TIE | UARTCTRL_TCIE | UARTCTRL_RIE); > lpuart32_write(port, temp, UARTCTRL); > >