The LS1028A has six LPUART controllers. Add the nodes.
This was tested on a custom board.
Signed-off-by: Michael Walle <michael@xxxxxxxx>
---
.../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 73 +++++++++++++++++++
1 file changed, 73 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
index 0843cfbe7ae1..df51e81ebe84 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -333,6 +333,79 @@
status = "disabled";
};
+
+ lpuart0: serial@2260000 {
+ compatible = "fsl,ls1028a-lpuart";
+ reg = <0x0 0x2260000 0x0 0x1000>;
+ interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ dma-names = "rx","tx";
+ dmas = <&edma0 1 32>,
+ <&edma0 1 33>;
+ status = "disabled";
+ };
+
+ lpuart1: serial@2270000 {
+ compatible = "fsl,ls1028a-lpuart";
+ reg = <0x0 0x2270000 0x0 0x1000>;
+ interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ dma-names = "rx","tx";
+ dmas = <&edma0 1 30>,
+ <&edma0 1 31>;
+ status = "disabled";
+ };
+
+ lpuart2: serial@2280000 {
+ compatible = "fsl,ls1028a-lpuart";
+ reg = <0x0 0x2280000 0x0 0x1000>;
+ interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ dma-names = "rx","tx";
+ dmas = <&edma0 1 28>,
+ <&edma0 1 29>;
+ status = "disabled";
+ };
+
+ lpuart3: serial@2290000 {
+ compatible = "fsl,ls1028a-lpuart";
+ reg = <0x0 0x2290000 0x0 0x1000>;
+ interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ dma-names = "rx","tx";
+ dmas = <&edma0 1 26>,
+ <&edma0 1 27>;
+ status = "disabled";
+ };
+
+ lpuart4: serial@22a0000 {
+ compatible = "fsl,ls1028a-lpuart";
+ reg = <0x0 0x22a0000 0x0 0x1000>;
+ interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ dma-names = "rx","tx";
+ dmas = <&edma0 1 24>,
+ <&edma0 1 25>;
+ status = "disabled";
+ };
+
+ lpuart5: serial@22b0000 {
+ compatible = "fsl,ls1028a-lpuart";
+ reg = <0x0 0x22b0000 0x0 0x1000>;
+ interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clockgen 4 1>;
+ clock-names = "ipg";
+ dma-names = "rx","tx";
+ dmas = <&edma0 1 22>,
+ <&edma0 1 23>;
+ status = "disabled";
+ };
+
edma0: dma-controller@22c0000 {
#dma-cells = <2>;
compatible = "fsl,ls1028a-edma", "fsl,vf610-edma";
--
2.20.1
