Re: [PATCH v2 01/10] mailbox: Support blocking transfers in atomic context

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Thierry,

On Thu, Nov 22, 2018 at 2:47 AM Thierry Reding <thierry.reding@xxxxxxxxx> wrote:
>
> On Wed, Nov 21, 2018 at 08:18:22PM -0600, Jassi Brar wrote:
> > On Wed, Nov 21, 2018 at 8:27 AM Thierry Reding <thierry.reding@xxxxxxxxx> wrote:
> > >
> > > On Tue, Nov 20, 2018 at 04:29:07PM +0100, Thierry Reding wrote:
> > > > On Sat, Nov 17, 2018 at 11:27:17AM -0600, Jassi Brar wrote:
> > > > > On Mon, Nov 12, 2018 at 9:18 AM Thierry Reding <thierry.reding@xxxxxxxxx> wrote:
> > > > > >
> > > > > > From: Thierry Reding <treding@xxxxxxxxxx>
> > > > > >
> > > > > > The mailbox framework supports blocking transfers via completions for
> > > > > > clients that can sleep. In order to support blocking transfers in cases
> > > > > > where the transmission is not permitted to sleep, add a new ->flush()
> > > > > > callback that controller drivers can implement to busy loop until the
> > > > > > transmission has been completed. This will automatically be called when
> > > > > > available and interrupts are disabled for clients that request blocking
> > > > > > transfers.
> > > > > >
> > > > > > Signed-off-by: Thierry Reding <treding@xxxxxxxxxx>
> > > > > > ---
> > > > > >  drivers/mailbox/mailbox.c          | 8 ++++++++
> > > > > >  include/linux/mailbox_controller.h | 4 ++++
> > > > > >  2 files changed, 12 insertions(+)
> > > > > >
> > > > > > diff --git a/drivers/mailbox/mailbox.c b/drivers/mailbox/mailbox.c
> > > > > > index 674b35f402f5..0eaf21259874 100644
> > > > > > --- a/drivers/mailbox/mailbox.c
> > > > > > +++ b/drivers/mailbox/mailbox.c
> > > > > > @@ -267,6 +267,14 @@ int mbox_send_message(struct mbox_chan *chan, void *mssg)
> > > > > >                 unsigned long wait;
> > > > > >                 int ret;
> > > > > >
> > > > > > +               if (irqs_disabled() && chan->mbox->ops->flush) {
> > > > > > +                       ret = chan->mbox->ops->flush(chan, chan->cl->tx_tout);
> > > > > > +                       if (ret < 0)
> > > > > > +                               tx_tick(chan, ret);
> > > > > > +
> > > > > > +                       return ret;
> > > > > > +               }
> > > > > > +
> > > > > This is hacky. I think we can do without busy waiting in atomic
> > > > > context. You could queue locally while in atomic context and then
> > > > > transfer in blocking mode. I don't think we should worry about the
> > > > > 'throughput' as there already is no h/w rate control even with
> > > > > busy-waiting.
> > > >
> > > > I actually tried to do that before I added this flushing mechanism. The
> > > > problem is, like you said, one of rate control. As mentioned in the
> > > > cover letter, the shared mailboxes implemented in tegra-hsp are used as
> > > > RX and TX channels for the TCU, which is like a virtual UART. The TTY
> > > > driver included as part of this series will use one of the mailboxes to
> > > > transmit data that is written to the console. The problem is that if
> > > > these transmissions are not rate-limited on the TTY driver side, the
> > > > console will just keep writing data and eventually overflow the buffer
> > > > that we have in the mailbox subsystem.
> > > >
> > > > The problem is that data comes in at a much higher rate than what we can
> > > > output. This is especially true at boot when the TCU console takes over
> > > > and the whole log buffer is dumped on it.
> > > >
> > > > So the only way to rate-limit is to either make mbox_send_message()
> > > > block, but that can only be done in non-atomic context. The console,
> > > > however, will always run in atomic context, so the only way to do rate-
> > > > limiting is by busy looping.
> > >
> > > What I also tried before was to implement busy looping within the
> > > ->send_data() callback of the driver so that we didn't have to put this
> > > into the core. Unfortunately, however, the ->send_data() callback is
> > > called under chan->lock, which means that from mbox_send_message() we
> > > don't have a way to mark the transfer as done. In order to do that we'd
> > > have to call mbox_chan_txdone(), but that ends up calling tx_tick() and
> > > that in turn also attempts to take the chan->lock, which would cause a
> > > deadlock.
> > >
> > > The explicit flushing is the best alternative that I could come up with.
> > > I think it's not all that hacky, because it's very explicit about what's
> > > going on and it has the nice side-effect that it will allow the mailbox
> > > to work in interrupt driven mode if possible and only resorting to the
> > > busy loop in atomic context.
> > >
> > > At this point I think I have explored all other options and I frankly
> > > can't find a more proper way to achieve what we need here. Perhaps you
> > > can think of additional ways to accomplish this?
> > >
> > Well, I would have a local ring buffer (array) of enough size to hold
> > the characters and then have a task consuming data from that ring
> > buffer by transmitting over mailbox.
>
> There's already such a ringbuffer in the printk code. To implement what
> you suggest would effectively be creating a copy of that buffer because
> we'd be allocating the buffer and the console code would just dump each
> and every character in the logbuf into that ring buffer without rate-
> limitation.
>
Well, the console assumes there exists an atomic path to put character
on the bus, But because there isn't in case of tcu, we have to emulate
that. Frankly I prefer the one-off driver jump some hoops, rather than
implement exceptions in the api.
BTW, there is already no rate-limitation because its all virtual -
data is consumed as fast as possible.

> To make matters worse, the ringbuffer would be empty most of the time
> after the initial dump of the logbuf, so we'd be wasting all that buffer
> space.
>
The idea is console and uart-ops both feed into this buffer and the
only consumer thread runs the mailbox.

> It just seems to me like we should be keeping the TCU driver as close as
> possible to other UART drivers which also busy loop in order to rate-
> limit what the console can write. Given the current mailbox framework it
> is not possible to do that (in interrupt context), so an extension seems
> like the most sensible option.
>
> Perhaps you'd be less concerned about such a change if it was perhaps
> more explicit? Just throwing ideas around, I think something that could
> also work is if we explicitly add a mbox_flush() function that would
> basically be calling ->flush(). That way users of the mailbox can make
> their requirement very explicit. I haven't actually tested that, but I
> think it would work. Does that sound more acceptable to you?
>
I am happy to see features and bugfixes added to the api. What I am
not eager about is supporting less than 100% legit and very platform
specific usecases, especially when there is a work around.

Thanks.



[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux