On Wed, Nov 21, 2018 at 8:27 AM Thierry Reding <thierry.reding@xxxxxxxxx> wrote:
>
> On Tue, Nov 20, 2018 at 04:29:07PM +0100, Thierry Reding wrote:
> > On Sat, Nov 17, 2018 at 11:27:17AM -0600, Jassi Brar wrote:
> > > On Mon, Nov 12, 2018 at 9:18 AM Thierry Reding <thierry.reding@xxxxxxxxx> wrote:
> > > >
> > > > From: Thierry Reding <treding@xxxxxxxxxx>
> > > >
> > > > The mailbox framework supports blocking transfers via completions for
> > > > clients that can sleep. In order to support blocking transfers in cases
> > > > where the transmission is not permitted to sleep, add a new ->flush()
> > > > callback that controller drivers can implement to busy loop until the
> > > > transmission has been completed. This will automatically be called when
> > > > available and interrupts are disabled for clients that request blocking
> > > > transfers.
> > > >
> > > > Signed-off-by: Thierry Reding <treding@xxxxxxxxxx>
> > > > ---
> > > > drivers/mailbox/mailbox.c | 8 ++++++++
> > > > include/linux/mailbox_controller.h | 4 ++++
> > > > 2 files changed, 12 insertions(+)
> > > >
> > > > diff --git a/drivers/mailbox/mailbox.c b/drivers/mailbox/mailbox.c
> > > > index 674b35f402f5..0eaf21259874 100644
> > > > --- a/drivers/mailbox/mailbox.c
> > > > +++ b/drivers/mailbox/mailbox.c
> > > > @@ -267,6 +267,14 @@ int mbox_send_message(struct mbox_chan *chan, void *mssg)
> > > > unsigned long wait;
> > > > int ret;
> > > >
> > > > + if (irqs_disabled() && chan->mbox->ops->flush) {
> > > > + ret = chan->mbox->ops->flush(chan, chan->cl->tx_tout);
> > > > + if (ret < 0)
> > > > + tx_tick(chan, ret);
> > > > +
> > > > + return ret;
> > > > + }
> > > > +
> > > This is hacky. I think we can do without busy waiting in atomic
> > > context. You could queue locally while in atomic context and then
> > > transfer in blocking mode. I don't think we should worry about the
> > > 'throughput' as there already is no h/w rate control even with
> > > busy-waiting.
> >
> > I actually tried to do that before I added this flushing mechanism. The
> > problem is, like you said, one of rate control. As mentioned in the
> > cover letter, the shared mailboxes implemented in tegra-hsp are used as
> > RX and TX channels for the TCU, which is like a virtual UART. The TTY
> > driver included as part of this series will use one of the mailboxes to
> > transmit data that is written to the console. The problem is that if
> > these transmissions are not rate-limited on the TTY driver side, the
> > console will just keep writing data and eventually overflow the buffer
> > that we have in the mailbox subsystem.
> >
> > The problem is that data comes in at a much higher rate than what we can
> > output. This is especially true at boot when the TCU console takes over
> > and the whole log buffer is dumped on it.
> >
> > So the only way to rate-limit is to either make mbox_send_message()
> > block, but that can only be done in non-atomic context. The console,
> > however, will always run in atomic context, so the only way to do rate-
> > limiting is by busy looping.
>
> What I also tried before was to implement busy looping within the
> ->send_data() callback of the driver so that we didn't have to put this
> into the core. Unfortunately, however, the ->send_data() callback is
> called under chan->lock, which means that from mbox_send_message() we
> don't have a way to mark the transfer as done. In order to do that we'd
> have to call mbox_chan_txdone(), but that ends up calling tx_tick() and
> that in turn also attempts to take the chan->lock, which would cause a
> deadlock.
>
> The explicit flushing is the best alternative that I could come up with.
> I think it's not all that hacky, because it's very explicit about what's
> going on and it has the nice side-effect that it will allow the mailbox
> to work in interrupt driven mode if possible and only resorting to the
> busy loop in atomic context.
>
> At this point I think I have explored all other options and I frankly
> can't find a more proper way to achieve what we need here. Perhaps you
> can think of additional ways to accomplish this?
>
Well, I would have a local ring buffer (array) of enough size to hold
the characters and then have a task consuming data from that ring
buffer by transmitting over mailbox.
-jassi
