Re: [PATCH v2 1/4] tty: serial: Add 8250 earlycon to support noinit option

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 02/01/2015 11:27 AM, Peter Hurley wrote:
> Hi Eddie,
> 
> On 01/12/2015 08:08 AM, Eddie Huang wrote:
>> Add earlycon support not only baudrate option, but also add noinit option.
>> If use noinit option, 8250 earlycon will not init serial hardware and use
>> loader setting.
> 
> I see this went into Greg's tty-testing branch.
> 
> The only point of this is to not program the divisor, right?
> 
> I ask because early_serial8250_setup() could already handle this without
> extra options by simply not doing divisor programming if no baud option is
> present.

Does the patch below work for your use-case?

[ Note: the patch applies to 3.19-rcX. To test, your noinit patches need to be
  reverted first.
]

--- >% ---
From: Peter Hurley <peter@xxxxxxxxxxxxxxxxxx>
Subject: [PATCH] serial: 8250_early: Assume uart already initialized if no
 baud option

The <baud><parity><bit> option string is not supplied if the earlycon
is started via devicetree and OF_EARLYCON_DECLARE(). The option string
is also not required if started via kernel command line parameters of
the form:
  earlycon=uart,mmio,<addr>
  console=uart,mmio,<addr>

If earlycon_device->baud is 0, then an option string was not supplied.
In this case, assume the uart has already been initialized by the
bootloader or firmware.

Signed-off-by: Peter Hurley <peter@xxxxxxxxxxxxxxxxxx>
---
 drivers/tty/serial/8250/8250_early.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_early.c b/drivers/tty/serial/8250/8250_early.c
index d7b831b..1701d00 100644
--- a/drivers/tty/serial/8250/8250_early.c
+++ b/drivers/tty/serial/8250/8250_early.c
@@ -149,12 +149,18 @@ static int __init early_serial8250_setup(struct earlycon_device *device,
 		return 0;
 
 	if (!device->baud) {
+		struct uart_port *port = &device->port;
+		unsigned int ier;
+
 		device->baud = probe_baud(&device->port);
 		snprintf(device->options, sizeof(device->options), "%u",
 			 device->baud);
-	}
 
-	init_port(device);
+		/* assume the device was initialized, only mask interrupts */
+		ier = serial8250_early_in(port, UART_IER);
+		serial8250_early_out(port, UART_IER, ier & UART_IER_UUE);
+	} else
+		init_port(device);
 
 	device->con->write = early_serial8250_write;
 	return 0;
-- 
2.2.2

--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux