Re: [PATCH 10/10] drivers: PL011: add support for the ARM SBSA generic UART

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Mark,

On 16/01/15 18:12, Mark Rutland wrote:
> On Fri, Jan 16, 2015 at 06:07:42PM +0000, Andre Przywara wrote:
>> Hi Mark,
>>
>> On 16/01/15 17:34, Mark Rutland wrote:
>>> On Fri, Jan 16, 2015 at 05:23:06PM +0000, Andre Przywara wrote:
>>>> The ARM Server Base System Architecture[1] document describes a
>>>> generic UART which is a subset of the PL011 UART.
>>>> It lacks DMA support, baud rate control and modem status line
>>>> control, among other things.
>>>> The idea is to move the UART initialization and setup into the
>>>> firmware (which does this job today already) and let the kernel just
>>>> use the UART for sending and receiving characters.
>>>> We use the recent refactoring the build a new struct uart_ops
>>>> variable which points to some new functions avoiding access to the
>>>> missing registers. We reuse as much existing PL011 code as possible.
>>>>
>>>> In contrast to the PL011 the SBSA UART does not define any AMBA or
>>>> PrimeCell relations, so we go a pretty generic probe function
>>>> which only uses platform device functions.
>>>> A DT binding is provided, but other systems can easily attach to it,
>>>> too (hint, hint!).
>>>>
>>>> Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
>>>> ---
>>>>  .../devicetree/bindings/serial/arm_sbsa_uart.txt   |    9 ++
>>>>  drivers/tty/serial/amba-pl011.c                    |  154 ++++++++++++++++++++
>>>>  2 files changed, 163 insertions(+)
>>>>  create mode 100644 Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt b/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt
>>>> new file mode 100644
>>>> index 0000000..21d211f
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/serial/arm_sbsa_uart.txt
>>>> @@ -0,0 +1,9 @@
>>>> +* ARM SBSA defined generic UART
>>>> +This UART uses a subset of the PL011 registers and consequently lives
>>>> +in the PL011 driver. It's baudrate and other communication parameters
>>>> +cannot be adjusted at runtime, so it lacks a clock specifier here.
>>>> +
>>>> +Required properties:
>>>> +- compatible: must be "arm,sbsa-uart"
>>>> +- reg: exactly one register range
>>>> +- interrupts: exactly one interrupt specifier
>>>> diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
>>>> index a1c929f..596e641 100644
>>>> --- a/drivers/tty/serial/amba-pl011.c
>>>> +++ b/drivers/tty/serial/amba-pl011.c
>>>> @@ -101,6 +101,14 @@ static struct vendor_data vendor_arm = {
>>>>  	.get_fifosize		= get_fifosize_arm,
>>>>  };
>>>>  
>>>> +static struct vendor_data vendor_sbsa = {
>>>> +	.oversampling		= false,
>>>> +	.dma_threshold		= false,
>>>> +	.cts_event_workaround	= false,
>>>> +	.always_enabled		= true,
>>>> +	.fixed_options		= "115200n8",
>>>> +};
>>>
>>> Is this configuration mandated by the SBSA? If so, please mandate it in
>>> the binding document.
>>
>> No, actually it is just a placeholder. The driver needs some values to
>> avoid querying the device and to make the upper levels happy, so I went
>> with those. Actually 38400 would make more sense here, since that is
>> some kind of Linux serial default value.
> 
> Please let's have the real values rather than something made up.
> 
> If I ask my UART how it's configured, I expect it to tell me the truth.
> It's nice to know before I connect something to the other end of the
> line.

So you mean that the firmware (or the vendor) inserts the actual values
here, which the kernel and eventually userland can read?
Makes some sense, so what about:
-----------------------
Required properties:
- compatible: must be "arm,sbsa-uart"
- reg: exactly one register range
- interrupts: exactly one interrupt specifier

Optional properties:
- current-speed : the current active speed of the UART
- fifo-size : always 32 as per the SBSA specification
- word-size : the number of payload bits per word
- parity : used parity method, can be:
	"n": no parity
	"e": even parity
	"o": odd parity
	"m": always mark (logical 1)
	"s": always space (logical 0)
- stop-bits : the number of stop bits after the payload

The vendor or the firmware should set these values to match the actual
configuration of the UART. The SBSA spec does not provide ways of
changing those values.
----------------------------
While I copied the first two of the optional properties from
of-serial.txt, I made up the rest. Does they make sense?

Cheers,
Andre.

>>> If the rate and so on are not mandated, they should probably be
>>> described by the binding so software has a chance of getting the real
>>> configuration details.
>>
>> What the actual settings are is actually totally up to the firmware. By
>> definition software cannot learn these settings and it shouldn't care,
>> as the SBSA UART is just "meant to work(TM)". Though from userland it
>> looks like one can change the baudrate and the other parameters, the
>> driver totally ignores those settings (though it reflects it back).
> 
> The fact that we cannot reconfigure it is orthogonal.
> 
> Given that all we should need is baud-rate, parity, and bits, it should
> be relatively easy to describe and handle.
> 
> Mark.
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux