If the chosen baud rate is large enough (e.g. 3.5 megabaud), the
calculated n values in serial_omap_is_baud_mode16() may become 0. This
causes a division by zero when calculating the difference between
calculated and desired baud rates. To prevent this, cap the n13 and n16
values on 1.
Division by zero in kernel.
[<c00132e0>] (unwind_backtrace) from [<c00112ec>] (show_stack+0x10/0x14)
[<c00112ec>] (show_stack) from [<c01ed7bc>] (Ldiv0+0x8/0x10)
[<c01ed7bc>] (Ldiv0) from [<c023805c>] (serial_omap_baud_is_mode16+0x4c/0x68)
[<c023805c>] (serial_omap_baud_is_mode16) from [<c02396b4>] (serial_omap_set_termios+0x90/0x8d8)
[<c02396b4>] (serial_omap_set_termios) from [<c0230a0c>] (uart_change_speed+0xa4/0xa8)
[<c0230a0c>] (uart_change_speed) from [<c0231798>] (uart_set_termios+0xa0/0x1fc)
[<c0231798>] (uart_set_termios) from [<c022bb44>] (tty_set_termios+0x248/0x2c0)
[<c022bb44>] (tty_set_termios) from [<c022c17c>] (set_termios+0x248/0x29c)
[<c022c17c>] (set_termios) from [<c022c3e4>] (tty_mode_ioctl+0x1c8/0x4e8)
[<c022c3e4>] (tty_mode_ioctl) from [<c0227e70>] (tty_ioctl+0xa94/0xb18)
[<c0227e70>] (tty_ioctl) from [<c00cf45c>] (do_vfs_ioctl+0x4a0/0x560)
[<c00cf45c>] (do_vfs_ioctl) from [<c00cf568>] (SyS_ioctl+0x4c/0x74)
[<c00cf568>] (SyS_ioctl) from [<c000e480>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: Frans Klaver <frans.klaver@xxxxxxxxx>
---
Resend to add stable@xxxxxxxxxxxxxxx to CC. As far as I know, this applies to
v3.9 and up.
Thanks,
Frans
drivers/tty/serial/omap-serial.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index d017cec..e454b7c 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -254,8 +254,16 @@ serial_omap_baud_is_mode16(struct uart_port *port, unsigned int baud)
{
unsigned int n13 = port->uartclk / (13 * baud);
unsigned int n16 = port->uartclk / (16 * baud);
- int baudAbsDiff13 = baud - (port->uartclk / (13 * n13));
- int baudAbsDiff16 = baud - (port->uartclk / (16 * n16));
+ int baudAbsDiff13;
+ int baudAbsDiff16;
+
+ if (n13 == 0)
+ n13 = 1;
+ if (n16 == 0)
+ n16 = 1;
+
+ baudAbsDiff13 = baud - (port->uartclk / (13 * n13));
+ baudAbsDiff16 = baud - (port->uartclk / (16 * n16));
if (baudAbsDiff13 < 0)
baudAbsDiff13 = -baudAbsDiff13;
if (baudAbsDiff16 < 0)
--
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
