On Thu, Nov 15, 2012 at 03:53:47PM +0000, Alan Cox wrote:
> > Unfortunately we need the RS422 stuff - that's the reason for using the
> > DSC-200/300 card.
> >
> > Thanks for the comments and feedback - I'll take another look at things in
> > the light of the information. If the functionality we require requires a
> > significant amount of new code to be written, I suspect that the work will
> > be deemed too time consuming by those who call the shots. We'll see.
>
> First guess at what you need except for the RS422 registers is attached.
> To get the RS422 features working needs the tool tracing (or driver
> printks adding) to see what QMCR and QOPR bits map to which RS422
> features.
>
> Given that if you just force the bits you want in with the RS422 warning I
> expect it'll just work for your case and should then be trivial to add the
> ioctl.
Apologies for the delay in getting back to this.
With a minor change (the port IO base must be set prior to calling
pci_quatech_clock() and pci_quatech_rs422() in pci_quatech_setup()) this
seems to do the job for us (with a DSC-200/300 card). As it turns out, the
card configuration we need happens to match the power-on default state of
the card when the jumpers are not in use, so no further manipulation is
required at this stage. Revised patch is below, against the tty git tree.
I also tweaked the warning a little to make it clearer that it is the
software control of RS422 features that aren't supported. If the defaults
are fine (or the hardware jumpers are used to control the features) then
RS422 will work just fine.
So far as getting something working for our case, the patch below is all
that is required. I do know the QMCR and QOPR bit map details for at least
the DSC-200/300 card as it's more or less described in the manual. I will
try to prepare a second patch which at least creates the necessary defines
for these in the next few days.
With regard to the ioctl, should this be an implementation of the ioctl
provided by the old out-of-tree driver, or is there an established
standard/example which I should write against instead?
jonathan
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 17b7d26..43c6b4f 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1040,6 +1040,253 @@ static int pci_asix_setup(struct serial_private *priv,
return pci_default_setup(priv, board, port, idx);
}
+/* Quatech devices have their own extra interface features */
+
+struct quatech_feature {
+ u16 devid;
+ bool amcc;
+};
+
+#define QPCR_TEST_FOR1 0x3F
+#define QPCR_TEST_GET1 0x00
+#define QPCR_TEST_FOR2 0x40
+#define QPCR_TEST_GET2 0x40
+#define QPCR_TEST_FOR3 0x80
+#define QPCR_TEST_GET3 0x40
+#define QPCR_TEST_FOR4 0xC0
+#define QPCR_TEST_GET4 0x80
+
+#define QOPR_CLOCK_X1 0x0000
+#define QOPR_CLOCK_X2 0x0001
+#define QOPR_CLOCK_X4 0x0002
+#define QOPR_CLOCK_X8 0x0003
+#define QOPR_CLOCK_RATE_MASK 0x0003
+
+
+static struct quatech_feature quatech_cards[] = {
+ { PCI_DEVICE_ID_QUATECH_QSC100, 1 },
+ { PCI_DEVICE_ID_QUATECH_DSC100, 1 },
+ { PCI_DEVICE_ID_QUATECH_DSC100E, 0 },
+ { PCI_DEVICE_ID_QUATECH_DSC200, 1 },
+ { PCI_DEVICE_ID_QUATECH_DSC200E, 0 },
+ { PCI_DEVICE_ID_QUATECH_ESC100D, 1 },
+ { PCI_DEVICE_ID_QUATECH_ESC100M, 1 },
+ { PCI_DEVICE_ID_QUATECH_QSCP100, 1 },
+ { PCI_DEVICE_ID_QUATECH_DSCP100, 1 },
+ { PCI_DEVICE_ID_QUATECH_QSCP200, 1 },
+ { PCI_DEVICE_ID_QUATECH_DSCP200, 1 },
+ { PCI_DEVICE_ID_QUATECH_ESCLP100, 0 },
+ { PCI_DEVICE_ID_QUATECH_QSCLP100, 0 },
+ { PCI_DEVICE_ID_QUATECH_DSCLP100, 0 },
+ { PCI_DEVICE_ID_QUATECH_SSCLP100, 0 },
+ { PCI_DEVICE_ID_QUATECH_QSCLP200, 0 },
+ { PCI_DEVICE_ID_QUATECH_DSCLP200, 0 },
+ { PCI_DEVICE_ID_QUATECH_SSCLP200, 0 },
+ { PCI_DEVICE_ID_QUATECH_SPPXP_100, 0 },
+ { 0, }
+};
+
+static int pci_quatech_amcc(u16 devid)
+{
+ struct quatech_feature *qf = &quatech_cards[0];
+ while (qf->devid) {
+ if (qf->devid == devid)
+ return qf->amcc;
+ qf++;
+ }
+ pr_err("quatech: unknown port type '0x%04X'.\n", devid);
+ return 0;
+};
+
+static int pci_quatech_rqopr(struct uart_8250_port *port)
+{
+ unsigned long base = port->port.iobase;
+ u8 LCR, val;
+
+ LCR = inb(base + UART_LCR);
+ outb(0xBF, base + UART_LCR);
+ val = inb(base + UART_SCR);
+ outb(LCR, base + UART_LCR);
+ return val;
+}
+
+static void pci_quatech_wqopr(struct uart_8250_port *port, u8 qopr)
+{
+ unsigned long base = port->port.iobase;
+ u8 LCR, val;
+
+ LCR = inb(base + UART_LCR);
+ outb(0xBF, base + UART_LCR);
+ val = inb(base + UART_SCR);
+ outb(qopr, base + UART_SCR);
+ outb(LCR, base + UART_LCR);
+}
+
+static int pci_quatech_rqmcr(struct uart_8250_port *port)
+{
+ unsigned long base = port->port.iobase;
+ u8 LCR, val, qmcr;
+
+ LCR = inb(base + UART_LCR);
+ outb(0xBF, base + UART_LCR);
+ val = inb(base + UART_SCR);
+ outb(val | 0x10, base + UART_SCR);
+ qmcr = inb(base + UART_MCR);
+ outb(val, base + UART_SCR);
+ outb(LCR, base + UART_LCR);
+
+ return qmcr;
+}
+
+static void pci_quatech_wqmcr(struct uart_8250_port *port, u8 qmcr)
+{
+ unsigned long base = port->port.iobase;
+ u8 LCR, val;
+
+ LCR = inb(base + UART_LCR);
+ outb(0xBF, base + UART_LCR);
+ val = inb(base + UART_SCR);
+ outb(val | 0x10, base + UART_SCR);
+ outb(qmcr, base + UART_MCR);
+ outb(val, base + UART_SCR);
+ outb(LCR, base + UART_LCR);
+}
+
+static int pci_quatech_has_qmcr(struct uart_8250_port *port)
+{
+ unsigned long base = port->port.iobase;
+ u8 LCR, val;
+
+ LCR = inb(base + UART_LCR);
+ outb(0xBF, base + UART_LCR);
+ val = inb(base + UART_SCR);
+ if (val & 0x20) {
+ outb(0x80, UART_LCR);
+ if (!(inb(UART_SCR) & 0x20)) {
+ outb(LCR, base + UART_LCR);
+ return 1;
+ }
+ }
+ return 0;
+}
+
+static int pci_quatech_test(struct uart_8250_port *port)
+{
+ u8 reg;
+ u8 qopr = pci_quatech_rqopr(port);
+ pci_quatech_wqopr(port, qopr & QPCR_TEST_FOR1);
+ reg = pci_quatech_rqopr(port) & 0xC0;
+ if (reg != QPCR_TEST_GET1)
+ return -EINVAL;
+ pci_quatech_wqopr(port, (qopr & QPCR_TEST_FOR1)|QPCR_TEST_FOR2);
+ reg = pci_quatech_rqopr(port) & 0xC0;
+ if (reg != QPCR_TEST_GET2)
+ return -EINVAL;
+ pci_quatech_wqopr(port, (qopr & QPCR_TEST_FOR1)|QPCR_TEST_FOR3);
+ reg = pci_quatech_rqopr(port) & 0xC0;
+ if (reg != QPCR_TEST_GET3)
+ return -EINVAL;
+ pci_quatech_wqopr(port, (qopr & QPCR_TEST_FOR1)|QPCR_TEST_FOR4);
+ reg = pci_quatech_rqopr(port) & 0xC0;
+ if (reg != QPCR_TEST_GET4)
+ return -EINVAL;
+
+ pci_quatech_wqopr(port, qopr);
+ return 0;
+}
+
+static int pci_quatech_clock(struct uart_8250_port *port)
+{
+ u8 qopr, reg, set;
+ unsigned long clock;
+
+ if (pci_quatech_test(port) < 0)
+ return 1843200;
+
+ qopr = pci_quatech_rqopr(port);
+
+ pci_quatech_wqopr(port, qopr & ~QOPR_CLOCK_X8);
+ reg = pci_quatech_rqopr(port);
+ if (reg & QOPR_CLOCK_X8) {
+ clock = 1843200;
+ goto out;
+ }
+ pci_quatech_wqopr(port, qopr | QOPR_CLOCK_X8);
+ reg = pci_quatech_rqopr(port);
+ if (!(reg & QOPR_CLOCK_X8)) {
+ clock = 1843200;
+ goto out;
+ }
+ reg &= QOPR_CLOCK_X8;
+ if (reg == QOPR_CLOCK_X2) {
+ clock = 3685400;
+ set = QOPR_CLOCK_X2;
+ } else if (reg == QOPR_CLOCK_X4) {
+ clock = 7372800;
+ set = QOPR_CLOCK_X4;
+ } else if (reg == QOPR_CLOCK_X8) {
+ clock = 14745600;
+ set = QOPR_CLOCK_X8;
+ } else {
+ clock = 1843200;
+ set = QOPR_CLOCK_X1;
+ }
+ qopr &= ~QOPR_CLOCK_RATE_MASK;
+ qopr |= set;
+
+out:
+ pci_quatech_wqopr(port, qopr);
+ return clock;
+}
+
+static int pci_quatech_rs422(struct uart_8250_port *port)
+{
+ u8 qmcr;
+ int rs422 = 0;
+
+ if (!pci_quatech_has_qmcr(port))
+ return 0;
+ qmcr = pci_quatech_rqmcr(port);
+ pci_quatech_wqmcr(port, 0xFF);
+ if (pci_quatech_rqmcr(port))
+ rs422 = 1;
+ pci_quatech_wqmcr(port, qmcr);
+ return rs422;
+}
+
+static int pci_quatech_init(struct pci_dev *dev)
+{
+ if (pci_quatech_amcc(dev->device)) {
+ unsigned long base = pci_resource_start(dev, 0);
+ if (base) {
+ u32 tmp;
+ outl(inl(base + 0x38), base + 0x38);
+ tmp = inl(base + 0x3c);
+ outl(tmp | 0x01000000, base + 0x3c);
+ outl(tmp, base + 0x3c);
+ }
+ }
+ return 0;
+}
+
+static int pci_quatech_setup(struct serial_private *priv,
+ const struct pciserial_board *board,
+ struct uart_8250_port *port, int idx)
+{
+ /* Needed by pci_quatech calls below */
+ port->port.iobase = pci_resource_start(priv->dev, FL_GET_BASE(board->flags));
+ /* Set up the clocking */
+ port->port.uartclk = pci_quatech_clock(port);
+ /* For now just warn about RS422 */
+ if (pci_quatech_rs422(port))
+ pr_warn( "quatech: software control of RS422 features not currently supported.\n");
+ return pci_default_setup(priv, board, port, idx);
+}
+
+static void __devexit pci_quatech_exit(struct pci_dev *dev)
+{
+}
+
static int pci_default_setup(struct serial_private *priv,
const struct pciserial_board *board,
struct uart_8250_port *port, int idx)
@@ -1503,6 +1750,16 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.setup = pci_default_setup,
.exit = __devexit_p(pci_plx9050_exit),
},
+ /* Quatech */
+ {
+ .vendor = PCI_VENDOR_ID_QUATECH,
+ .device = PCI_ANY_ID,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .init = pci_quatech_init,
+ .setup = pci_quatech_setup,
+ .exit = __devexit_p(pci_quatech_exit),
+ },
/*
* SBS Technologies, Inc., PMC-OCTALPRO 232
*/
@@ -3257,18 +3514,70 @@ static struct pci_device_id serial_pci_tbl[] = {
{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_ROMULUS,
0x10b5, 0x106a, 0, 0,
pbn_plx_romulus },
+ /*
+ * Quatech cards. These actually have configurable clocks but for
+ * now we just use the default.
+ *
+ * 100 series are RS232, 200 series RS422,
+ */
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_QSC100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_4_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSC100,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_2_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSC100E,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_2_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSC200,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_2_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSC200E,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_2_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_QSC200,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_4_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_ESC100D,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_8_115200 },
{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_ESC100M,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b1_8_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_QSCP100,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_4_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSCP100,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_2_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_QSCP200,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_4_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSCP200,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b1_2_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_QSCLP100,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_4_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSCLP100,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_2_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_SSCLP100,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_1_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_QSCLP200,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_4_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_DSCLP200,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_2_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_SSCLP200,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b2_1_115200 },
+ { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_ESCLP100,
+ PCI_ANY_ID, PCI_ANY_ID, 0, 0,
+ pbn_b0_8_115200 },
+
{ PCI_VENDOR_ID_SPECIALIX, PCI_DEVICE_ID_OXSEMI_16PCI954,
PCI_VENDOR_ID_SPECIALIX, PCI_SUBDEVICE_ID_SPECIALIX_SPEED4,
0, 0,
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index 9d36b82..ce45006 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -1867,8 +1867,23 @@
#define PCI_VENDOR_ID_QUATECH 0x135C
#define PCI_DEVICE_ID_QUATECH_QSC100 0x0010
#define PCI_DEVICE_ID_QUATECH_DSC100 0x0020
+#define PCI_DEVICE_ID_QUATECH_DSC200 0x0030
+#define PCI_DEVICE_ID_QUATECH_QSC200 0x0040
#define PCI_DEVICE_ID_QUATECH_ESC100D 0x0050
#define PCI_DEVICE_ID_QUATECH_ESC100M 0x0060
+#define PCI_DEVICE_ID_QUATECH_QSCP100 0x0120
+#define PCI_DEVICE_ID_QUATECH_DSCP100 0x0130
+#define PCI_DEVICE_ID_QUATECH_QSCP200 0x0140
+#define PCI_DEVICE_ID_QUATECH_DSCP200 0x0150
+#define PCI_DEVICE_ID_QUATECH_QSCLP100 0x0170
+#define PCI_DEVICE_ID_QUATECH_DSCLP100 0x0180
+#define PCI_DEVICE_ID_QUATECH_DSC100E 0x0181
+#define PCI_DEVICE_ID_QUATECH_SSCLP100 0x0190
+#define PCI_DEVICE_ID_QUATECH_QSCLP200 0x01A0
+#define PCI_DEVICE_ID_QUATECH_DSCLP200 0x01B0
+#define PCI_DEVICE_ID_QUATECH_DSC200E 0x01B1
+#define PCI_DEVICE_ID_QUATECH_SSCLP200 0x01C0
+#define PCI_DEVICE_ID_QUATECH_ESCLP100 0x01E0
#define PCI_DEVICE_ID_QUATECH_SPPXP_100 0x0278
#define PCI_VENDOR_ID_SEALEVEL 0x135e
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
