On Tue, Jan 29 2008, Jens Axboe wrote: > On Tue, Jan 29 2008, Matthew Dharm wrote: > > On Tue, Jan 29, 2008 at 07:39:11PM +0100, Jens Axboe wrote: > > > On Tue, Jan 29 2008, Jens Axboe wrote: > > > > On Tue, Jan 29 2008, Oliver Neukum wrote: > > > > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe: > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote: > > > > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <jens.axboe@xxxxxxxxxx> wrote: > > > > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote: > > > > > > > >> Greg KH wrote: > > > > > > > > > > > > > No difference, still just a lot of resets. > > > > > > > > > > > > > > > Where you able to figure out which usb storage transport is used? > > > > > > > > > > > > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport() > > > > > > > functions. I'm not sure if these get stored in sysfs perhaps. This will > > > > > > > pinpoint better where to look. Let me research a bit. > > > > > > > > > > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and > > > > > > transport is 'Bulk' > > > > > > > > > > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG > > > > > That should tell the reason for the resets. > > > > > > > > Sure, I'll do that. Will post the results tonight. > > > > > > OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged > > > in the device, waited 10 seconds or so and pulled it out. These are the > > > messages. > > > > > > It all looks good until the MODE_SENSE command, where it only transfers > > > 4 of 192 bytes. > > > > No, that's not the problem. This is the problem: > > It's where the problem starts, otherwise there would not be a need to > sense :-) > > > > usb-storage: *** thread awakened. > > > usb-storage: Command TEST_UNIT_READY (6 bytes) > > > usb-storage: 00 00 00 00 00 00 > > > usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6 > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes > > > usb-storage: Status code 0; transferred 31/31 > > > usb-storage: -- transfer complete > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: Attempting to get CSW... > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes > > > usb-storage: Status code 0; transferred 13/13 > > > usb-storage: -- transfer complete > > > usb-storage: Bulk status result = 0 > > > usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1 > > > usb-storage: -- transport indicates command failure > > > usb-storage: Issuing auto-REQUEST_SENSE > > > usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6 > > > usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes > > > usb-storage: Status code 0; transferred 31/31 > > > usb-storage: -- transfer complete > > > usb-storage: Bulk command transfer result=0 > > > usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries > > > usb-storage: usb_sg_init returned -22 > > > usb-storage: Bulk data transfer result 0x4 > > > usb-storage: -- auto-sense failure > > > usb-storage: storage_pre_reset > > > ehci_hcd 0000:00:1d.7: port 1 high speed > > > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT > > > usb 5-1: reset high speed USB device using ehci_hcd and address 2 > > > ehci_hcd 0000:00:1d.7: port 1 high speed > > > ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT > > > usb-storage: storage_post_reset > > > usb-storage: usb_reset_composite_device returns 0 > > > usb-storage: scsi cmd done, result=0x70000 > > > usb-storage: *** thread sleeping. > > > > For some reason, usb_sg_init is boned during auto-sense. > > My guess would be that sg == NULL, hence the -EINVAL. Yep, trace below: WARNING: at drivers/usb/storage/transport.c:426 usb_stor_bulk_transfer_sglist() Pid: 12536, comm: usb-storage Not tainted 2.6.24 #74 [<7810541a>] show_trace_log_lvl+0x1a/0x30 [<78105e82>] show_trace+0x12/0x20 [<7810689c>] dump_stack+0x6c/0x80 [<f83e267e>] usb_stor_bulk_transfer_sglist+0x14e/0x160 [usb_storage] [<f83e2730>] usb_stor_bulk_srb_length+0x30/0x50 [usb_storage] [<f83e2762>] usb_stor_bulk_srb+0x12/0x20 [usb_storage] [<f83e2ce0>] usb_stor_Bulk_transport+0x190/0x3d0 [usb_storage] [<f83e30d6>] usb_stor_invoke_transport+0x1b6/0x320 [usb_storage] [<f83e1a38>] usb_stor_transparent_scsi_command+0x8/0x10 [usb_storage] [<f83e3813>] usb_stor_control_thread+0x143/0x2c0 [usb_storage] [<7813bc02>] kthread+0x42/0x70 [<78104fab>] kernel_thread_helper+0x7/0x1c ======================= usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries, sg 00000000 usb-storage: usb_sg_init returned -22 -- Jens Axboe - To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
