On Tue, Jan 29 2008, Jens Axboe wrote: > On Tue, Jan 29 2008, Oliver Neukum wrote: > > Am Dienstag, 29. Januar 2008 15:11:08 schrieb Jens Axboe: > > > On Tue, Jan 29 2008, Boaz Harrosh wrote: > > > > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <jens.axboe@xxxxxxxxxx> wrote: > > > > > On Tue, Jan 29 2008, Boaz Harrosh wrote: > > > > >> Greg KH wrote: > > > > > > > No difference, still just a lot of resets. > > > > > > > > > Where you able to figure out which usb storage transport is used? > > > > > > > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport() > > > > functions. I'm not sure if these get stored in sysfs perhaps. This will > > > > pinpoint better where to look. Let me research a bit. > > > > > > Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and > > > transport is 'Bulk' > > > > You can recompile your kernel with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG > > That should tell the reason for the resets. > > Sure, I'll do that. Will post the results tonight. OK, fresh boot with CONFIG_USB_DEBUG and CONFIG_STORAGE_DEBUG. Plugged in the device, waited 10 seconds or so and pulled it out. These are the messages. It all looks good until the MODE_SENSE command, where it only transfers 4 of 192 bytes. usb usb5: usb resume ehci_hcd 0000:00:1d.7: resume root hub hub 5-0:1.0: hub_resume hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0000 ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT hub 5-0:1.0: port 1, status 0501, change 0001, 480 Mb/s hub 5-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: new high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: default language 0x0409 usb 5-1: uevent usb 5-1: usb_probe_device usb 5-1: configuration #1 chosen from 1 choice usb 5-1: adding 5-1:1.0 (config #1, interface 0) usb 5-1:1.0: uevent drivers/usb/core/inode.c: creating file '002' usb 5-1: new device strings: Mfr=0, Product=3, SerialNumber=4 usb 5-1: Product: Flash Reader usb 5-1: SerialNumber: 02206 Initializing USB Mass Storage driver... usb-storage 5-1:1.0: usb_probe_interface usb-storage 5-1:1.0: usb_probe_interface - got id usb-storage: USB Mass Storage device detected usb-storage: -- associate_dev usb-storage: Vendor: 0x05e3, Product: 0x0760, Revision: 0x0125 usb-storage: Interface Subclass: 0x06, Protocol: 0x50 usb trans Bulk usb-storage: Transport: Bulk usb proto Transparent SCSI usb-storage: Protocol: Transparent SCSI scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: *** thread sleeping. usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1 usb-storage: GetMaxLUN command result is 1, data is 3 usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command INQUIRY (6 bytes) usb-storage: 12 00 00 00 24 00 usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries usb-storage: Status code 0; transferred 36/36 usb-storage: -- transfer complete usb-storage: Bulk data transfer result 0x0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0 ANSI: 0 usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command READ_CAPACITY (10 bytes) usb-storage: 25 00 00 00 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x3 L 8 F 128 Trg 0 LUN 0 CL 10 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries usb-storage: Status code 0; transferred 8/8 usb-storage: -- transfer complete usb-storage: Bulk data transfer result 0x0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB) usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command MODE_SENSE (6 bytes) usb-storage: 1a 00 3f 00 c0 00 usb-storage: Bulk Command S 0x43425355 T 0x4 L 192 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries usb-storage: Status code -121; transferred 4/192 usb-storage: -- short read transfer usb-storage: Bulk data transfer result 0x1 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code -32; transferred 0/13 usb-storage: clearing endpoint halt for pipe 0xc0008280 usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0 usb-storage: usb_stor_clear_halt: result = 0 usb-storage: Attempting to get CSW (2nd try)... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x4 R 188 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x5 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes) usb-storage: 1e 00 00 00 01 00 usb-storage: Bulk Command S 0x43425355 T 0x6 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x6 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x7 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x7 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command READ_CAPACITY (10 bytes) usb-storage: 25 00 00 00 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x8 L 8 F 128 Trg 0 LUN 0 CL 10 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries usb-storage: Status code 0; transferred 8/8 usb-storage: -- transfer complete usb-storage: Bulk data transfer result 0x0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x8 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB) usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command MODE_SENSE (6 bytes) usb-storage: 1a 00 3f 00 c0 00 usb-storage: Bulk Command S 0x43425355 T 0x9 L 192 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries usb-storage: Status code -121; transferred 4/192 usb-storage: -- short read transfer usb-storage: Bulk data transfer result 0x1 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code -32; transferred 0/13 usb-storage: clearing endpoint halt for pipe 0xc0008280 usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0 usb-storage: usb_stor_clear_halt: result = 0 usb-storage: Attempting to get CSW (2nd try)... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x9 R 188 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sdb:<7>usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command READ_10 (10 bytes) usb-storage: 28 00 00 00 00 00 00 00 08 00 usb-storage: Bulk Command S 0x43425355 T 0xa L 4096 F 128 Trg 0 LUN 0 CL 10 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries usb-storage: Status code 0; transferred 4096/4096 usb-storage: -- transfer complete usb-storage: Bulk data transfer result 0x0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0xa R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. sdb1 usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes) usb-storage: 1e 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0xb L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0xb R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. sd 6:0:0:0: [sdb] Attached SCSI removable disk sd 6:0:0:0: Attached scsi generic sg1 type 0 usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command INQUIRY (6 bytes) usb-storage: 12 00 00 00 24 00 usb-storage: Bulk Command S 0x43425355 T 0xc L 36 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries usb-storage: Status code 0; transferred 36/36 usb-storage: -- transfer complete usb-storage: Bulk data transfer result 0x0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0xc R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0 ANSI: 0 usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0xf L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0xf R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x10 L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x11 L 0 F 0 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x11 R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x12 L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x13 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x13 R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x14 L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x15 L 0 F 0 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x15 R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x16 L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x17 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x17 R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x18 L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x19 L 0 F 0 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x19 R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x1a L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x1b L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x1b R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x1c L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x1d L 0 F 0 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x1d R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x1e L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x1f L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x1f R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x20 L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x21 L 0 F 0 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x21 R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x22 L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x23 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x23 R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x24 L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command READ_CAPACITY (10 bytes) usb-storage: 25 00 00 00 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x25 L 8 F 128 Trg 0 LUN 1 CL 10 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries usb-storage: Status code -32; transferred 0/8 usb-storage: clearing endpoint halt for pipe 0xc0008280 usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0 usb-storage: usb_stor_clear_halt: result = 0 usb-storage: Bulk data transfer result 0x2 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x25 R 8 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: -- unexpectedly short transfer usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x26 L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: Status code -75; transferred 0/18 usb-storage: -- babble usb-storage: Bulk data transfer result 0x3 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code -75; transferred 0/13 usb-storage: -- babble usb-storage: Bulk status result = 3 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x27 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x27 R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x28 L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command READ_CAPACITY (10 bytes) usb-storage: 25 00 00 00 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x29 L 8 F 128 Trg 0 LUN 1 CL 10 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries usb-storage: Status code -32; transferred 0/8 usb-storage: clearing endpoint halt for pipe 0xc0008280 usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0 usb-storage: usb_stor_clear_halt: result = 0 usb-storage: Bulk data transfer result 0x2 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x29 R 8 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: -- unexpectedly short transfer usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x2a L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: Status code -75; transferred 0/18 usb-storage: -- babble usb-storage: Bulk data transfer result 0x3 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code -75; transferred 0/13 usb-storage: -- babble usb-storage: Bulk status result = 3 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x2b L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x2b R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x2c L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command READ_CAPACITY (10 bytes) usb-storage: 25 00 00 00 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x2d L 8 F 128 Trg 0 LUN 1 CL 10 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries usb-storage: Status code -32; transferred 0/8 usb-storage: clearing endpoint halt for pipe 0xc0008280 usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0 usb-storage: usb_stor_clear_halt: result = 0 usb-storage: Bulk data transfer result 0x2 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x2d R 8 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: -- unexpectedly short transfer usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x2e L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: Status code -75; transferred 0/18 usb-storage: -- babble usb-storage: Bulk data transfer result 0x3 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code -75; transferred 0/13 usb-storage: -- babble usb-storage: Bulk status result = 3 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x2f L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x2f R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x30 L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command READ_CAPACITY (10 bytes) usb-storage: 25 00 00 00 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x31 L 8 F 128 Trg 0 LUN 1 CL 10 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries usb-storage: Status code -32; transferred 0/8 usb-storage: clearing endpoint halt for pipe 0xc0008280 usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0 usb-storage: usb_stor_clear_halt: result = 0 usb-storage: Bulk data transfer result 0x2 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x31 R 8 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: -- unexpectedly short transfer usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x32 L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: Status code -75; transferred 0/18 usb-storage: -- babble usb-storage: Bulk data transfer result 0x3 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code -75; transferred 0/13 usb-storage: -- babble usb-storage: Bulk status result = 3 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x33 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x33 R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x34 L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command READ_CAPACITY (10 bytes) usb-storage: 25 00 00 00 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x35 L 8 F 128 Trg 0 LUN 1 CL 10 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries usb-storage: Status code -32; transferred 0/8 usb-storage: clearing endpoint halt for pipe 0xc0008280 usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0 usb-storage: usb_stor_clear_halt: result = 0 usb-storage: Bulk data transfer result 0x2 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x35 R 8 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: -- unexpectedly short transfer usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x36 L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: Status code -75; transferred 0/18 usb-storage: -- babble usb-storage: Bulk data transfer result 0x3 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code -75; transferred 0/13 usb-storage: -- babble usb-storage: Bulk status result = 3 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x37 L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x37 R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x38 L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command READ_CAPACITY (10 bytes) usb-storage: 25 00 00 00 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x39 L 8 F 128 Trg 0 LUN 1 CL 10 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries usb-storage: Status code -32; transferred 0/8 usb-storage: clearing endpoint halt for pipe 0xc0008280 usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=81 len=0 usb-storage: usb_stor_clear_halt: result = 0 usb-storage: Bulk data transfer result 0x2 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x39 R 8 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: -- unexpectedly short transfer usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x3a L 18 F 128 Trg 0 LUN 1 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: Status code -75; transferred 0/18 usb-storage: -- babble usb-storage: Bulk data transfer result 0x3 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code -75; transferred 0/13 usb-storage: -- babble usb-storage: Bulk status result = 3 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns 0 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk Command S 0x43425355 T 0x3b L 0 F 0 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x3b R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk Command S 0x43425355 T 0x3c L 18 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries usb-storage: usb_sg_init returned -22 usb-storage: Bulk data transfer result 0x4 usb-storage: -- auto-sense failure usb-storage: storage_pre_reset ehci_hcd 0000:00:1d.7: port 1 high speed ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT hub 5-0:1.0: state 7 ports 8 chg 0000 evt 0002 usb 5-1: reset high speed USB device using ehci_hcd and address 2 ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes ehci_hcd 0000:00:1d.7: devpath 1 ep0in 3strikes ehci_hcd 0000:00:1d.7: GetStatus port 1 status 001002 POWER sig=se0 CSC hub 5-0:1.0: logical disconnect on port 1 usb-storage: storage_post_reset usb-storage: usb_reset_composite_device returns -19 usb-storage: usb_stor_Bulk_reset called usb-storage: usb_stor_control_msg: rq=ff rqtype=21 value=0000 index=00 len=0 usb-storage: Soft reset failed: -19 usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand called hub 5-0:1.0: state 7 ports 8 chg 0002 evt 0002 hub 5-0:1.0: port 1, status 0100, change 0000, 12 Mb/s usb 5-1: USB disconnect, address 2 usb 5-1: unregistering device usb 5-1: usb_disable_device nuking all URBs usb 5-1: unregistering interface 5-1:1.0 usb-storage: storage_disconnect() called usb-storage: usb_stor_stop_transport called usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect sd 6:0:0:1: [sdc] READ CAPACITY failed sd 6:0:0:1: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK sd 6:0:0:1: [sdc] Sense not available. usb-storage: queuecommand called usb-storage: Fail command during disconnect sd 6:0:0:1: [sdc] Write Protect is off sd 6:0:0:1: [sdc] Mode Sense: 00 00 00 00 sd 6:0:0:1: [sdc] Assuming drive cache: write through sd 6:0:0:1: [sdc] Attached SCSI removable disk sd 6:0:0:1: Attached scsi generic sg2 type 0 usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect sd 6:0:0:0: [sdb] READ CAPACITY failed sd 6:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK sd 6:0:0:0: [sdb] Sense not available. usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: *** thread awakened. usb-storage: -- exiting usb-storage: queuecommand called usb-storage: Fail command during disconnect sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 00 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: queuecommand called usb-storage: Fail command during disconnect usb-storage: device scan complete usb-storage: -- usb_stor_release_resources usb-storage: -- sending exit command to thread scsi 6:0:0:0: [sdb] READ CAPACITY failed scsi 6:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK scsi 6:0:0:0: [sdb] Sense not available. scsi 6:0:0:0: rejecting I/O to dead device scsi 6:0:0:0: [sdb] Write Protect is off scsi 6:0:0:0: [sdb] Mode Sense: 00 00 00 00 scsi 6:0:0:0: [sdb] Assuming drive cache: write through scsi 6:0:0:0: rejecting I/O to dead device usb-storage: -- dissociate_dev usb 5-1:1.0: uevent usb 5-1: uevent hub 5-0:1.0: hub_suspend usb usb5: bus auto-suspend ehci_hcd 0000:00:1d.7: suspend root hub -- Jens Axboe - To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
