On Tue, Jan 29 2008, Boaz Harrosh wrote: > On Tue, Jan 29 2008 at 15:54 +0200, Jens Axboe <jens.axboe@xxxxxxxxxx> wrote: > > On Tue, Jan 29 2008, Boaz Harrosh wrote: > >> Greg KH wrote: > >>> On Mon, Jan 28, 2008 at 09:49:35PM +0100, Jens Axboe wrote: > >>>> Hi, > >>>> > >>>> Running latest -git (head 91525300baf162e83e923b09ca286f9205e21522) and > >>>> connecting my cf usb storage device yields and endless stream of: > >>>> > >>>> Initializing USB Mass Storage driver... > >>>> scsi6 : SCSI emulation for USB Mass Storage devices > >>>> usb-storage: device found at 2 > >>>> usb-storage: waiting for device to settle before scanning > >>>> usbcore: registered new interface driver usb-storage > >>>> USB Mass Storage support registered. > >>>> scsi 6:0:0:0: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0 > >>>> ANSI: 0 > >>>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB) > >>>> sd 6:0:0:0: [sdb] Write Protect is off > >>>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00 > >>>> sd 6:0:0:0: [sdb] Assuming drive cache: write through > >>>> sd 6:0:0:0: [sdb] 4001760 512-byte hardware sectors (2049 MB) > >>>> sd 6:0:0:0: [sdb] Write Protect is off > >>>> sd 6:0:0:0: [sdb] Mode Sense: 02 00 00 00 > >>>> sd 6:0:0:0: [sdb] Assuming drive cache: write through > >>>> sdb: sdb1 > >>>> sd 6:0:0:0: [sdb] Attached SCSI removable disk > >>>> sd 6:0:0:0: Attached scsi generic sg1 type 0 > >>>> scsi 6:0:0:1: Direct-Access Generic STORAGE DEVICE 0125 PQ: 0 > >>>> ANSI: 0 > >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2 > >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2 > >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2 > >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2 > >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2 > >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2 > >>>> usb 5-1: reset high speed USB device using ehci_hcd and address 2 > >>>> [...] > >>>> > >>>> until I disconnect it. The device doesn't work. Worked fine in 2.6.24. > >>>> I'm attaching boot messages and my .config. > >>> That's a bit wierd, as we haven't added any USB patches to the -git tree > >>> yet after 2.6.24 :) > >>> > >>> Could this be caused by some scsi changes perhaps? > >>> > >>> thanks, > >>> > >>> greg k-h > >>> - > >> Yes it is ;) > >> > >> Jens could you test the patch below? if it works I'll submit a proper > >> patch. Please forgive me for the bug. > > > > No difference, still just a lot of resets. > > > Where you able to figure out which usb storage transport is used? > > in drivers/usb/storage/usb.c you have get_protocol() and get_transport() > functions. I'm not sure if these get stored in sysfs perhaps. This will > pinpoint better where to look. Let me research a bit. Did the quick'n easy and dumped it. Protocol is 'Transparent SCSI' and transport is 'Bulk' -- Jens Axboe - To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
