On Monday 21 November 2005 05:53, you wrote:
> I don't think slave_configure is the right place to be modifying
> a scsi_host attribute. How about this patch instead? Only compile
> tested.
Patch applied on 2.6.15-rc2, and gives no better result:
# sg_readcap -16 -vv /dev/sdb
read capacity (16) cdb: 9e 10 00 00 00 00 00 00 00 00 00 00 00 20 00 00
READ CAPACITY 16 command error: Host_status=0x0b [DID_SOFT_ERROR]
dmesg output:
--------------------------------------------------------------------------
ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 106 (level, low) -> IRQ 25
scsi3 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 3960D Ultra160 SCSI adapter>
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Vendor: IFT Model: A16U-G1410 Rev: 342J
Type: Direct-Access ANSI SCSI revision: 05
scsi3:A:4:0: Tagged Queuing enabled. Depth 32
target3:0:4: Beginning Domain Validation
target3:0:4: wide asynchronous.
target3:0:4: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 127)
target3:0:4: Ending Domain Validation
sdc : very big device. try to use READ CAPACITY(16).
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 3 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 2 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 3 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 2 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 3 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 2 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 3 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 2 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 3 - Abort Tag Completed.
sdc : READ CAPACITY(16) failed.
sdc : status=0, message=00, host=7, driver=00
sdc : use 0xffffffff as device size
SCSI device sdc: 4294967296 512-byte hdwr sectors (2199023 MB)
SCSI device sdc: drive cache: write back
sdc : very big device. try to use READ CAPACITY(16).
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 2 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 3 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 2 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 3 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 2 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 3 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 2 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 3 - Abort Tag Completed.
(scsi3:A:4:0): No or incomplete CDB sent to device.
(scsi3:A:4:0): Protocol violation in Message-in phase. Attempting to abort.
(scsi3:A:4:0): Abort Tag Message Sent
(scsi3:A:4:0): SCB 2 - Abort Tag Completed.
sdc : READ CAPACITY(16) failed.
sdc : status=0, message=00, host=7, driver=00
sdc : use 0xffffffff as device size
SCSI device sdc: 4294967296 512-byte hdwr sectors (2199023 MB)
SCSI device sdc: drive cache: write back
sdc: sdc1
sd 3:0:4:0: Attached scsi disk sdc
sd 3:0:4:0: Attached scsi generic sg3 type 0
--------------------------------------------------------------------------
Does this mean the HBA has an hardware limit?
Thanks and regards,
--
Kilian CAVALOTTI Administrateur réseaux et systèmes
UPMC / CNRS - LIP6 (C870)
8, rue du Capitaine Scott Tel. : 01 44 27 88 54
75015 Paris - France Fax. : 01 44 27 70 00
-
: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
