On 25/07/2023 21:15, Henrik Grimler wrote: > On Sun, Jul 23, 2023 at 04:24:17PM +0200, Krzysztof Kozlowski wrote: >> Add full description of USB-MUIC (MAX77693 MUIC) and MUIC-MHL >> connections, along with proper USB connector and OTG mode for DWC2 USB >> controller. >> >> This fixes dtc W=1 warnings: >> >> Warning (graph_child_address): /i2c-mhl/hdmi-bridge@39/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary >> >> Cc: Marek Szyprowski <m.szyprowski@xxxxxxxxxxx> >> Cc: replicant@xxxxxxxxxx >> Cc: phone-devel@xxxxxxxxxxxxxxx >> Cc: ~postmarketos/upstreaming@xxxxxxxxxxx >> Cc: Martin Jücker <martin.juecker@xxxxxxxxx> >> Cc: Henrik Grimler <henrik@xxxxxxxxxx> >> Cc: Artur Weber <aweber.kernel@xxxxxxxxx> >> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx> > > Tested-by: Henrik Grimler <henrik@xxxxxxxxxx> > > * Peripheral mode (still) works > * MHL somewhat works > * OTG (still) does not work > > Further details for those interested: > > MHL works reliably if cable is attached before boot, but if cable is > attached on already running device it sometimes work after detaching > and attaching cable a few times. On cable attach, when it does not > work, we get: > > [ 252.831734] max77693-muic max77693-muic: external connector is detached(chg_type:0x0, prev_chg_type:0x0) > [ 253.733916] max77693-muic max77693-muic: external connector is attached(chg_type:0x1, prev_chg_type:0x1) > [ 253.735232] max77693-muic max77693-muic: CONTROL1 : 0x09, CONTROL2 : 0x04, state : attached > [ 254.691877] i2c i2c-15: sendbytes: NAK bailout. > [ 254.692150] sii9234 15-0039: writebm: TPI[0x3d] <- 0x3e > [ 255.984336] sii9234 15-0039: RGND is not 1k > [ 256.068970] sii9234 15-0039: RSEN_HIGH without RGND_1K > [ 256.104457] sii9234 15-0039: discovery failed, no power for MHL? > [ 256.118272] i2c i2c-15: sendbytes: NAK bailout. > [ 256.118539] sii9234 15-0039: writebm: TPI[0x3d] <- 0x3e > [ 256.375966] sii9234 15-0039: RSEN_HIGH without RGND_1K > [ 256.411561] sii9234 15-0039: discovery failed, no power for MHL? > > while when it works: > > [ 175.348307] max77693-muic max77693-muic: external connector is detached(chg_type:0x1, prev_chg_type:0x0) > [ 175.349576] max77693-muic max77693-muic: CONTROL1 : 0x00, CONTROL2 : 0x01, state : detached > [ 179.304373] dwc2 12480000.usb: new device is full-speed > [ 179.305920] max77693-muic max77693-muic: external connector is detached(chg_type:0x0, prev_chg_type:0x0) > [ 180.205735] max77693-muic max77693-muic: external connector is attached(chg_type:0x1, prev_chg_type:0x1) > [ 180.207211] max77693-muic max77693-muic: CONTROL1 : 0x09, CONTROL2 : 0x04, state : attached > [ 180.309727] i2c i2c-15: sendbytes: NAK bailout. > [ 180.309996] sii9234 15-0039: writebm: TPI[0x3d] <- 0x3e > > Not sure if issue here is in muic driver or sii9234 driver. > > OTG still does not seem to work, the muic driver detects (only) a > detach when OTG cable is attached: > > max77693-muic max77693-muic: external connector is detached(chg_type:0x0, prev_chg_type:0x0) > > Same happened when otg cable was attached before these hsotg changes > as well. I suppose issue here is with max77693-muic driver. > Thanks for testing. I miss here one important thing - did anything regressed? Is MHL behaving not worse than before? OTG, as non-working, matters less in such case. Best regards, Krzysztof
