On Sun, Jul 23, 2023 at 04:24:17PM +0200, Krzysztof Kozlowski wrote:
> Add full description of USB-MUIC (MAX77693 MUIC) and MUIC-MHL
> connections, along with proper USB connector and OTG mode for DWC2 USB
> controller.
>
> This fixes dtc W=1 warnings:
>
> Warning (graph_child_address): /i2c-mhl/hdmi-bridge@39/ports: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
>
> Cc: Marek Szyprowski <m.szyprowski@xxxxxxxxxxx>
> Cc: replicant@xxxxxxxxxx
> Cc: phone-devel@xxxxxxxxxxxxxxx
> Cc: ~postmarketos/upstreaming@xxxxxxxxxxx
> Cc: Martin Jücker <martin.juecker@xxxxxxxxx>
> Cc: Henrik Grimler <henrik@xxxxxxxxxx>
> Cc: Artur Weber <aweber.kernel@xxxxxxxxx>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
Tested-by: Henrik Grimler <henrik@xxxxxxxxxx>
* Peripheral mode (still) works
* MHL somewhat works
* OTG (still) does not work
Further details for those interested:
MHL works reliably if cable is attached before boot, but if cable is
attached on already running device it sometimes work after detaching
and attaching cable a few times. On cable attach, when it does not
work, we get:
[ 252.831734] max77693-muic max77693-muic: external connector is detached(chg_type:0x0, prev_chg_type:0x0)
[ 253.733916] max77693-muic max77693-muic: external connector is attached(chg_type:0x1, prev_chg_type:0x1)
[ 253.735232] max77693-muic max77693-muic: CONTROL1 : 0x09, CONTROL2 : 0x04, state : attached
[ 254.691877] i2c i2c-15: sendbytes: NAK bailout.
[ 254.692150] sii9234 15-0039: writebm: TPI[0x3d] <- 0x3e
[ 255.984336] sii9234 15-0039: RGND is not 1k
[ 256.068970] sii9234 15-0039: RSEN_HIGH without RGND_1K
[ 256.104457] sii9234 15-0039: discovery failed, no power for MHL?
[ 256.118272] i2c i2c-15: sendbytes: NAK bailout.
[ 256.118539] sii9234 15-0039: writebm: TPI[0x3d] <- 0x3e
[ 256.375966] sii9234 15-0039: RSEN_HIGH without RGND_1K
[ 256.411561] sii9234 15-0039: discovery failed, no power for MHL?
while when it works:
[ 175.348307] max77693-muic max77693-muic: external connector is detached(chg_type:0x1, prev_chg_type:0x0)
[ 175.349576] max77693-muic max77693-muic: CONTROL1 : 0x00, CONTROL2 : 0x01, state : detached
[ 179.304373] dwc2 12480000.usb: new device is full-speed
[ 179.305920] max77693-muic max77693-muic: external connector is detached(chg_type:0x0, prev_chg_type:0x0)
[ 180.205735] max77693-muic max77693-muic: external connector is attached(chg_type:0x1, prev_chg_type:0x1)
[ 180.207211] max77693-muic max77693-muic: CONTROL1 : 0x09, CONTROL2 : 0x04, state : attached
[ 180.309727] i2c i2c-15: sendbytes: NAK bailout.
[ 180.309996] sii9234 15-0039: writebm: TPI[0x3d] <- 0x3e
Not sure if issue here is in muic driver or sii9234 driver.
OTG still does not seem to work, the muic driver detects (only) a
detach when OTG cable is attached:
max77693-muic max77693-muic: external connector is detached(chg_type:0x0, prev_chg_type:0x0)
Same happened when otg cable was attached before these hsotg changes
as well. I suppose issue here is with max77693-muic driver.
Best regards,
Henrik Grimler
> ---
>
> Changes in v2:
> 1. Put connector node in the muic node (Henrik)
>
> Not tested on hardware. Please kindly check if peripheral mode is not
> broken. Or maybe OTG started to work?
> ---
> .../boot/dts/samsung/exynos4412-midas.dtsi | 50 ++++++++++++++++++-
> 1 file changed, 49 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/samsung/exynos4412-midas.dtsi b/arch/arm/boot/dts/samsung/exynos4412-midas.dtsi
> index 57836d5554d0..7daf25865551 100644
> --- a/arch/arm/boot/dts/samsung/exynos4412-midas.dtsi
> +++ b/arch/arm/boot/dts/samsung/exynos4412-midas.dtsi
> @@ -182,6 +182,38 @@ pmic@66 {
> pinctrl-0 = <&max77693_irq>;
> reg = <0x66>;
>
> + muic {
> + compatible = "maxim,max77693-muic";
> +
> + connector {
> + compatible = "samsung,usb-connector-11pin",
> + "usb-b-connector";
> + label = "micro-USB";
> + type = "micro";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + muic_to_usb: endpoint {
> + remote-endpoint = <&usb_to_muic>;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> +
> + muic_to_mhl: endpoint {
> + remote-endpoint = <&mhl_to_muic>;
> + };
> + };
> + };
> + };
> + };
> +
> regulators {
> esafeout1_reg: ESAFEOUT1 {
> regulator-name = "ESAFEOUT1";
> @@ -287,6 +319,14 @@ mhl_to_hdmi: endpoint {
> remote-endpoint = <&hdmi_to_mhl>;
> };
> };
> +
> + port@1 {
> + reg = <1>;
> +
> + mhl_to_muic: endpoint {
> + remote-endpoint = <&muic_to_mhl>;
> + };
> + };
> };
> };
> };
> @@ -545,8 +585,16 @@ hdmi_to_mhl: endpoint {
> &hsotg {
> vusb_d-supply = <&ldo15_reg>;
> vusb_a-supply = <&ldo12_reg>;
> - dr_mode = "peripheral";
> + dr_mode = "otg";
> + role-switch-default-mode = "peripheral";
> + usb-role-switch;
> status = "okay";
> +
> + port {
> + usb_to_muic: endpoint {
> + remote-endpoint = <&muic_to_usb>;
> + };
> + };
> };
>
> &i2c_0 {
> --
> 2.34.1
>
