On 2015년 12월 10일 10:20, Krzysztof Kozlowski wrote:
> On 10.12.2015 10:09, Chanwoo Choi wrote:
>> On 2015년 12월 10일 09:44, Krzysztof Kozlowski wrote:
>>> On 09.12.2015 13:07, Chanwoo Choi wrote:
>>>> This patch adds the DMC (Dynamic Memory Controller) bus node for Exynos3250 SoC.
>>>> The DMC is an AMBA AXI-compliant slave to interface external JEDEC standard
>>>> SDRAM devices. The bus includes the OPP tables and the source clock for DMC
>>>> block.
>>>>
>>>> Following list specifies the detailed relation between the clock and DMC block:
>>>> - The source clock of DMC block : div_dmc
>>>>
>>>> Signed-off-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
>>>> ---
>>>> arch/arm/boot/dts/exynos3250.dtsi | 34 ++++++++++++++++++++++++++++++++++
>>>> 1 file changed, 34 insertions(+)
>>>>
>>>> diff --git a/arch/arm/boot/dts/exynos3250.dtsi b/arch/arm/boot/dts/exynos3250.dtsi
>>>> index 2f30d632f1cc..7214c5e42150 100644
>>>> --- a/arch/arm/boot/dts/exynos3250.dtsi
>>>> +++ b/arch/arm/boot/dts/exynos3250.dtsi
>>>> @@ -687,6 +687,40 @@
>>>> clock-names = "ppmu";
>>>> status = "disabled";
>>>> };
>>>> +
>>>> + bus_dmc: bus_dmc {
>>>> + compatible = "samsung,exynos-bus";
>>>> + clocks = <&cmu_dmc CLK_DIV_DMC>;
>>>> + clock-names = "bus";
>>>> + operating-points-v2 = <&bus_dmc_opp_table>;
>>>> + status = "disabled";
>>>> + };
>>>> +
>>>> + bus_dmc_opp_table: opp_table1 {
>>>
>>> This is the firsy opp_table, right? So:
>>> s/opp_table1/opp_table0/
>>
>> Right. It is first opp_table in exynos3250.dtsi.
>> But, I'm considering the OPP table of CPU freqeuncy as opp_table0.
>> So, I have the plan that support the operation-points-v2 for Exynos3250 CPU.
>
> Ok
>
>>
>>>
>>>> + compatible = "operating-points-v2";
>>>> + opp-shared;
>>>> +
>>>> + opp00 {
>>>> + opp-hz = /bits/ 64 <50000000>;
>>>> + opp-microvolt = <800000>;
>>>> + };
>>>> + opp01 {
>>>> + opp-hz = /bits/ 64 <100000000>;
>>>> + opp-microvolt = <800000>;
>>>> + };
>>>> + opp02 {
>>>> + opp-hz = /bits/ 64 <134000000>;
>>>> + opp-microvolt = <800000>;
>>>
>>> Why 134, not 133 MHz?
>>
>> When I used the 133000000, the source clock is changed to 100Mhz instead of 133MHz.
>> I add following test result on exynos3250-rinato board.
>>
>> Case1.
>> When I use the 134 MHz, the source clock is changed to 133MHz
>> : exynos-bus soc:bus_dmc: old_freq(200000000) -> new_freq (134000000) (real: 133333334)
>>
>> Case2.
>> When I use the 133 MHz, the source clock is changed to 100MHz
>> : exynos-bus soc:bus_dmc: old_freq(200000000) -> new_freq (133000000) (real: 100000000)
>
> Now I remember that issue. You could use here directly 133333334 but
> that also would look a little bit weird... so 134 is ok for me. Could
> just add a comment that desired frequency is actually "133 MHz"?
Do you prefer among following example?
Example1.
opp02 {
/* The desired frequency is 133MHz because
* clock change has the dependency on clock driver.
* When set rate as 134MHz, the clock driver would
* change the 133MHz actually instead of 134MHz.
*/
opp-hz = /bits/ 64 <134000000>;
opp-microvolt = <800000>;
};
Example2.
opp02 {
opp-hz = /bits/ 64 <133333334>;
opp-microvolt = <800000>;
};
Best Regards,
Chanwoo Choi
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
