On Mon, Dec 09, 2013 at 10:24:52AM -0500, Alan Stern wrote: > On Mon, 9 Dec 2013, Vikas Sajjan wrote: > > > Does warm reset while activating SuperSpeed HUBs if the hub activate type > > is HUB_RESET_RESUME. > > > > When we do Suspend-to-RAM with (any one of the 16, 32, 64 Jetflash) transcend > > USB 3.0 device connected on 3.0 port, during resume I noticed that the > > XHCI controller has moved to sometimes RECOVERY, POLLING or INACTIVE STATE. > > This behaviour is inconsistent and the connection with connected USB 3.0 device > > on 3.0 port was LOST. Does the device eventually re-connect on the USB port? Or is warm reset necessary to make the device connect? Does the xHCI register restore complete after resume from S3, or is power lost? I'm trying to figure out whether xhci_reset is called before your issue is triggered. > > Doing warm reset while activating SuperSpeed HUBs if the hub > > activate type is HUB_RESET_RESUME, gets the connected device to the stable state. > > > > Reviewed at https://chromium-review.googlesource.com/#/c/177132/ > > > > Tested on exynos5420 and exynos5250 with Transcend Jetflash USB 3.0 device (8564:1000) Is this issue specific to the particular USB device manufacturer (Transcend)? Does the same device lose connection on resume from S3 with other host controller vendors? Have you seen this issue when the USB 3.0 device is behind a USB 3.0 hub? I ask because this sounds like a low-level link training issue that's specific to the exynos host or USB device. I would rather track down which hardware is to blame than generically add a warm reset for all USB 3.0 devices. > > rebased on Greg Kroah-Hartman's usb-next > > git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb.git > > > > Signed-off-by: Vikas Sajjan <vikas.sajjan@xxxxxxxxxxx> > > --- > > drivers/usb/core/hub.c | 41 +++++++++++++++++++++++++---------------- > > 1 file changed, 25 insertions(+), 16 deletions(-) > > > > diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c > > index a7c04e2..d8432b0 100644 > > --- a/drivers/usb/core/hub.c > > +++ b/drivers/usb/core/hub.c > > > @@ -1093,6 +1108,16 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) > > u16 portstatus, portchange; > > > > portstatus = portchange = 0; > > + > > + /* Some connected devices might be still in unknown state even > > + * after reset-resume, a WARM_RESET gets the connected device > > + * to the normal state. > > + */ > > + if (udev && hub_is_superspeed(hub->hdev) && > > + type == HUB_RESET_RESUME) > > + hub_port_reset(hub, port1, NULL, > > + HUB_BH_RESET_TIME, true); > > Please don't do this all the time to every attached port. Do it only > when it is really needed. Agreed. Can we at least limit the warm reset to devices directly attached to roothubs? You can also change this code to get the port status and only do the warm reset if the port link state is USB_SS_PORT_LS_POLLING, USB_SS_PORT_LS_RX_DETECT, or USB_SS_PORT_LS_SS_INACTIVE. > Shouldn't you pass udev as the third argument? If not, please explain > why not. > > Finally, I don't see why you put this in hub_activate(). Isn't it more > closely connected with the reset-resume procedure for the child device? Sarah Sharp -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |