Hi Jacopo,
Thank you for the patch.
On Wednesday, 5 September 2018 18:29:45 EEST Jacopo Mondi wrote:
> Add HDMI and CVBS inputs device nodes to R-Car E3 Ebisu board.
>
> Both HDMI and CVBS inputs are connected to an ADV7482 video decoder hooked
> to the SoC CSI-2 receiver port.
>
> Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts | 86 +++++++++++++++++++++++
> 1 file changed, 86 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
> b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts index 2bc3a48..d2faf3e
> 100644
> --- a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
> +++ b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
> @@ -28,6 +28,29 @@
> /* first 128MB is reserved for secure area. */
> reg = <0x0 0x48000000 0x0 0x38000000>;
> };
> +
> + cvbs-in {
> + compatible = "composite-video-connector";
> + label = "CVBS IN";
> +
> + port {
> + cvbs_con: endpoint {
> + remote-endpoint = <&adv7482_ain7>;
> + };
> + };
> + };
> +
> + hdmi-in {
> + compatible = "hdmi-connector";
> + label = "HDMI IN";
> + type = "a";
> +
> + port {
> + hdmi_in_con: endpoint {
> + remote-endpoint = <&adv7482_hdmi>;
> + };
> + };
> + };
> };
>
> &avb {
> @@ -47,6 +70,22 @@
> };
> };
>
> +&csi40 {
> + status = "okay";
> +
> + ports {
> + port@0 {
> + reg = <0>;
> +
> + csi40_in: endpoint {
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + remote-endpoint = <&adv7482_txa>;
> + };
> + };
> + };
> +};
> +
> &ehci0 {
> status = "okay";
> };
> @@ -55,6 +94,49 @@
> clock-frequency = <48000000>;
> };
>
> +&i2c0 {
> + status = "okay";
> +
> + video-receiver@70 {
> + compatible = "adi,adv7482";
> + reg = <0x70>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + interrupt-parent = <&gpio0>;
> + interrupt-names = "intrq1", "intrq2";
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>,
> + <17 IRQ_TYPE_LEVEL_LOW>;
> +
> + port@7 {
> + reg = <7>;
> +
> + adv7482_ain7: endpoint {
> + remote-endpoint = <&cvbs_con>;
> + };
> + };
> +
> + port@8 {
> + reg = <8>;
> +
> + adv7482_hdmi: endpoint {
> + remote-endpoint = <&hdmi_in_con>;
> + };
> + };
> +
> + port@a {
> + reg = <0xa>;
> +
> + adv7482_txa: endpoint {
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + remote-endpoint = <&csi40_in>;
> + };
> + };
> + };
> +};
> +
> &ohci0 {
> status = "okay";
> };
> @@ -94,6 +176,10 @@
> status = "okay";
> };
>
> +&vin4 {
> + status = "okay";
> +};
> +
> &xhci0 {
> pinctrl-0 = <&usb30_pins>;
> pinctrl-names = "default";
--
Regards,
Laurent Pinchart
