Add HDMI and CVBS inputs device nodes to R-Car E3 Ebisu board.
Both HDMI and CVBS inputs are connected to an ADV7482 video decoder hooked to
the SoC CSI-2 receiver port.
Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
---
arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts | 86 ++++++++++++++++++++++++++
1 file changed, 86 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
index 2bc3a48..d2faf3e 100644
--- a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts
@@ -28,6 +28,29 @@
/* first 128MB is reserved for secure area. */
reg = <0x0 0x48000000 0x0 0x38000000>;
};
+
+ cvbs-in {
+ compatible = "composite-video-connector";
+ label = "CVBS IN";
+
+ port {
+ cvbs_con: endpoint {
+ remote-endpoint = <&adv7482_ain7>;
+ };
+ };
+ };
+
+ hdmi-in {
+ compatible = "hdmi-connector";
+ label = "HDMI IN";
+ type = "a";
+
+ port {
+ hdmi_in_con: endpoint {
+ remote-endpoint = <&adv7482_hdmi>;
+ };
+ };
+ };
};
&avb {
@@ -47,6 +70,22 @@
};
};
+&csi40 {
+ status = "okay";
+
+ ports {
+ port@0 {
+ reg = <0>;
+
+ csi40_in: endpoint {
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ remote-endpoint = <&adv7482_txa>;
+ };
+ };
+ };
+};
+
&ehci0 {
status = "okay";
};
@@ -55,6 +94,49 @@
clock-frequency = <48000000>;
};
+&i2c0 {
+ status = "okay";
+
+ video-receiver@70 {
+ compatible = "adi,adv7482";
+ reg = <0x70>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ interrupt-parent = <&gpio0>;
+ interrupt-names = "intrq1", "intrq2";
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>,
+ <17 IRQ_TYPE_LEVEL_LOW>;
+
+ port@7 {
+ reg = <7>;
+
+ adv7482_ain7: endpoint {
+ remote-endpoint = <&cvbs_con>;
+ };
+ };
+
+ port@8 {
+ reg = <8>;
+
+ adv7482_hdmi: endpoint {
+ remote-endpoint = <&hdmi_in_con>;
+ };
+ };
+
+ port@a {
+ reg = <0xa>;
+
+ adv7482_txa: endpoint {
+ clock-lanes = <0>;
+ data-lanes = <1 2>;
+ remote-endpoint = <&csi40_in>;
+ };
+ };
+ };
+};
+
&ohci0 {
status = "okay";
};
@@ -94,6 +176,10 @@
status = "okay";
};
+&vin4 {
+ status = "okay";
+};
+
&xhci0 {
pinctrl-0 = <&usb30_pins>;
pinctrl-names = "default";
--
2.7.4
