Re: [PATCH v7 1/2] dt-bindings: display: bridge: Document THC63LVD1024 LVDS decoder

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Jacopo,

On Saturday, 7 April 2018 12:45:56 EEST jacopo mondi wrote:
> On Fri, Apr 06, 2018 at 06:40:14PM +0300, Laurent Pinchart wrote:
> > Hi Jacopo,
> > 
> > (CC'ing Mark Brown)
> 
> Hi Mark
> 
> [snip]
> 
> >> Anyway, we spent enough time on naming issues, starting from my first
> >> stupid 'pdwn' permutations then on this semi-standard names.
> >> 
> >> I'll send next version with 'powerdown-gpios' and 'oe-gpios'
> >> properties hoping that would be finally accepted by everyone.
> > 
> > I certainly won't complain (as long as you write pwdn instead of pdwn in
> > the driver :-)).
> 
> Oh, so you won't complain if I address your comments? Thank you! :D
> By the way, the dumb pdwn name comes, again, from the chip name. I can
> change it to a saner name for sure...

And I've just realized that, I thought it was a typo :-/ If it comes with the 
datasheet I'm fine with either.

> >> Same on the mandatory/optional VCC supply thing. Let's try to make
> >> next version the final one. If the optional property with the dummy
> >> regulator doesn't satisfy you and it is preferred to have a
> >> fixed-regulator anyhow in DT I'll do in next version, othewise let's try
> >> not to change it again. I'll just remark here that in the current Eagle
> >> design vcc is connected to a power rail with no regulator at all :)
> > 
> > I don't like the dummy regulator much, as it generates a dev_warn(), which
> > makes me believe that it's a hack rather than a proper solution. You might
> > want to ask Mark Brown for his opinion.
> 
> Sure: Hi Mark, a bit of context here to save you a long(er) reading.
> 
> Unsurprisingly, the chip for which I'm writing this small driver needs
> a power supply to be properly functional :) In the development board
> it is installed on, the power supply is connected to a power rail,
> with no regulator. At the same time, some other designs may instead
> include a regulator.

To be precise, with an always-on regulator that can't be software-controlled.

> I assume that's a very common situation. I started by describing the
> regulator as optional in DT bindings, and use regulator_get_optional(). If
> that function returns PTR_ERR, the regulator is then ignored in driver's
> power management routines.
> 
> In this last version I thought I was acting smart and copied what happens
> in other DRM bridges like adv7511, which use 'regulator_get()' and work
> with a dummy if no regulator is provided in DT. Laurent has the above
> doubts on using a dummy, and I actually share some of his concerns
> (that dev_warn() is how I found out adv7511 was using a dummy, actually).
> 
> To sum up: when a regulator is described as optional in DT, do you
> suggest to work with a dummy if it's not there, or use the _optional()
> version of regulator_get() and manually set it to NULL and ignore it
> in the enable/disable driver's routines?
> 
> Bonus question: Laurent likes to have the regulator described as required,
> and thus require it to be described in DT also in cases where it is not
> actually there using a 'fixed-regulator' and refuse to probe if the
> regulator is not available. Do you encourage this approach, or prefer to
> have it optional and handle it in the driver in one of the above described
> ways?

-- 
Regards,

Laurent Pinchart






[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux