Re: [PATCH 2/2] pinctrl: sh-pfc: r8a7795: Use lookup function for bias data

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Nov 3, 2016 at 6:10 PM, Laurent Pinchart
<laurent.pinchart@xxxxxxxxxxxxxxxx> wrote:
> On Thursday 03 Nov 2016 16:34:21 Niklas Söderlund wrote:
>> There is a bug in the r8a7795 bias code where a WARN() is trigged
>> anytime a pin from PUEN0/PUD0is accessed.
>>
>>  # cat /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins
>>
>>  WARNING: CPU: 2 PID: 2391 at drivers/pinctrl/sh-pfc/pfc-r8a7795.c:5364
>> r8a7795_pinmux_get_bias+0xbc/0xc8 [..]
>>  Call trace:
>>  [<ffff0000083c442c>] r8a7795_pinmux_get_bias+0xbc/0xc8
>>  [<ffff0000083c37f4>] sh_pfc_pinconf_get+0x194/0x270
>>  [<ffff0000083b0768>] pin_config_get_for_pin+0x20/0x30
>>  [<ffff0000083b11e8>] pinconf_generic_dump_one+0x168/0x188
>>  [<ffff0000083b144c>] pinconf_generic_dump_pins+0x5c/0x98
>>  [<ffff0000083b0628>] pinconf_pins_show+0xc8/0x128
>>  [<ffff0000081fe3bc>] seq_read+0x16c/0x420
>>  [<ffff00000831a110>] full_proxy_read+0x58/0x88
>>  [<ffff0000081d7ad4>] __vfs_read+0x1c/0xf8
>>  [<ffff0000081d8874>] vfs_read+0x84/0x148
>>  [<ffff0000081d9d64>] SyS_read+0x44/0xa0
>>  [<ffff000008082f4c>] __sys_trace_return+0x0/0x4
>>
>> This is due to the WARN() check if the reg field of the pullups struct
>> is zero, and this should be 0 for pins controlled by the PUEN0/PUD0
>> registers. Change the layout of the pullups struct to embed the pin
>> number inside the struct and loop over it to fetch the correct
>> information or WARN() if no pin is found.
>
> This lowers the memory consumption at the cost of increased CPU usage. Given
> that the get/set bias functions are not part of a critical path I'm fine with
> that. We could possibly optimize the implementation by using a dichotomic
> search, but I don't think that's needed at the moment.

Alternatively, we could steal one bit from the "reg" bitifield to
add a "present" bit, without increasing the table size:

        static const struct {
                u16 present : 1;
                u16 reg : 10;
                u16 bit : 5;
         } pullups[] = {

While 10 bits is not sufficient in general (the PFC register block size
is 0x50c), it's good enough to address the PUx registers. And if needed,
we can switch from register byte offsets to register indices, indexing the
32-bit register file.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds




[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux