Hi Bjorn, As you probably noticed already, I added you to the thread modifying the A3700 periph clock driver, we have concerns about the PCIe specificities. Bjorn Helgaas <bhelgaas@xxxxxxxxxx> wrote on Mon, 26 Nov 2018 08:50:51 -0600: > On Fri, Nov 23, 2018 at 8:18 AM Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote: > > > > Hello, > > > > As part of an effort to bring suspend to RAM support to Armada 3700 > > SoCs (main target: ESPRESSObin), this series handles the work around > > the PCIe IP. > > > > First, more configuration is done in the 'setup' helper as inspired > > from the U-Boot driver. This is needed to entirely initialize the IP > > during future resume operation (patch 1). > > > > Then, reset GPIO, PHY and clock support are introduced (patch 2-4). As > > current device trees do not provide the corresponding properties, not > > finding one of these properties is not an error and just produces a > > warning. However, if the property is present, an error during PHY > > initialization will fail the probe of the driver. > > > > Note: To be sure the clock will be resumed before this driver, a first > > series adding links between clocks and consumers has been submitted, > > see [1]. > > > > Patch 5 adds suspend/resume hooks, re-using all the above. > > > > Finally, bindings and device trees are updated to reflect the hardware > > (patch 6-12). While the clock depends on the SoC, the reset GPIO and > > the PHY depends on the board so the clock is added in the > > armada-37xx.dtsi file while the two other properties are added in > > armada-3720-espressobin.dts. > > > > [1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-November/614527.html > > > > Thanks, > > Miquèl > > > > > > Miquel Raynal (12): > > PCI: aardvark: configure more registers in the configuration helper > > PCI: aardvark: add reset GPIO support > > PCI: aardvark: add PHY support > > PCI: aardvark: add clock support > > PCI: aardvark: add suspend to RAM support > > dt-bindings: PCI: aardvark: describe the reset-gpios property > > dt-bindings: PCI: aardvark: describe the clocks property > > dt-bindings: PCI: aardvark: describe the PHY property > > ARM64: dts: marvell: armada-37xx: declare PCIe reset pin > > ARM64: dts: marvell: armada-3720-espressobin: declare PCIe reset GPIO > > ARM64: dts: marvell: armada-37xx: declare PCIe clock > > ARM64: dts: marvell: armada-3720-espressobin: declare PCIe PHY > > Hi Miquèl, > > Thanks for your work! If/when you post a v2, please run "git log > --oneline" and adjust your subject lines to match the capitalization > conventions, i.e., for PCI, start the description with a capital > letter: "PCI: aardvark: Add suspend to RAM support". > Hum sorry, I noticed the upper case "PCI:" but I missed the other capitalization. I had no review yet but I'll certainly send a v2 with this fixed. > BTW, I notice you closed your email with "Miquèl", but the patches > contain "Miquel". you *should* be able to use the correctly accented > version of your name in the Signed-off-by lines. I have tripped over > some tool issues, but if we pay attention, we should be able to get it > to work. Indeed, I'm surprised that you noticed it! Even in France where éèàï are quite common I very often get my first name screwed so I gave up two years ago and decided to switch to ascii-only characters in my 'digital' life. Now it's harder to switch again, for example git log --author would not recognize "Miquèl" and "Miquel" to be the same person... > > > .../devicetree/bindings/pci/aardvark-pci.txt | 9 + > > .../dts/marvell/armada-3720-espressobin.dts | 4 + > > arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 5 + > > drivers/pci/controller/pci-aardvark.c | 214 ++++++++++++++++++ > > 4 files changed, 232 insertions(+) > > > > -- > > 2.19.1 > > Thanks, Miquèl
