Re: [PATCH v3] PCI/AER: Enable reporting for ports enumerated after AER driver registration

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Oct 11, 2018 at 08:26:18AM -0700, Bjorn Helgaas wrote:
> From: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
> 
> Previously we enabled AER error reporting only for Switch Ports that were
> enumerated prior to registering the AER service driver.  Switch Ports
> enumerated after AER driver registration were left with error reporting
> disabled.
> 
> A common order, which works correctly, is that we enumerate devices before
> registering portdrv and the AER driver:
> 
>   - Enumerate all the devices at boot-time
> 
>   - Register portdrv and bind it to all Root Ports and Switch Ports, which
>     disables error reporting for these Ports
> 
>   - Register AER service driver and bind it to all Root Ports, which
>     enables error reporting for the Root Ports and any Switch Ports below
>     them
> 
> But if we enumerate devices *after* registering portdrv and the AER driver,
> e.g., if a host bridge driver is loaded as a module, error reporting is not
> enabled correctly:
> 
>   - Register portdrv and AER driver (this happens at boot-time)
> 
>   - Enumerate a Root Port
> 
>   - Bind portdrv to Root Port, disabling its error reporting
> 
>   - Bind AER service driver to Root Port, enabling error reporting for it
>     and its children (there are no children, since we haven't enumerated
>     them yet)
> 
>   - Enumerate Switch Port below the Root Port
> 
>   - Bind portdrv to Switch Port, disabling its error reporting
> 
>   - AER service driver doesn't bind to Switch Ports, so error reporting
>     remains disabled
> 
> Hot-adding a Switch fails similarly: error reporting is enabled correctly
> for the Root Port, but when the Switch is enumerated, the AER service
> driver doesn't claim it, so there's nothing to enable error reporting for
> the Switch Ports.
> 
> Change the AER service driver so it binds to *all* PCIe Ports, including
> Switch Upstream and Downstream Ports.  Enable AER error reporting for all
> these Ports, but not for any children.
> 
> Link: https://lore.kernel.org/linux-pci/1536085989-2956-1-git-send-email-jonathan.derrick@xxxxxxxxx
> Based-on-patch-by: Jon Derrick <jonathan.derrick@xxxxxxxxx>
> Signed-off-by: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
> ---
>  drivers/pci/pcie/aer.c |   16 +++++++++-------
>  1 file changed, 9 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/pci/pcie/aer.c b/drivers/pci/pcie/aer.c
> index 90b53abf621d..c40c6607849b 100644
> --- a/drivers/pci/pcie/aer.c
> +++ b/drivers/pci/pcie/aer.c
> @@ -1316,12 +1316,6 @@ static void aer_enable_rootport(struct aer_rpc *rpc)
>  	pci_read_config_dword(pdev, aer_pos + PCI_ERR_UNCOR_STATUS, &reg32);
>  	pci_write_config_dword(pdev, aer_pos + PCI_ERR_UNCOR_STATUS, reg32);
>  
> -	/*
> -	 * Enable error reporting for the root port device and downstream port
> -	 * devices.
> -	 */
> -	set_downstream_devices_error_reporting(pdev, true);
> -
>  	/* Enable Root Port's interrupt in response to error messages */
>  	pci_read_config_dword(pdev, aer_pos + PCI_ERR_ROOT_COMMAND, &reg32);
>  	reg32 |= ROOT_PORT_INTR_ON_MESG_MASK;
> @@ -1378,10 +1372,17 @@ static void aer_remove(struct pcie_device *dev)
>   */
>  static int aer_probe(struct pcie_device *dev)
>  {
> +	struct pci_dev *pdev = dev->port;
> +	int type = pci_pcie_type(pdev);
>  	int status;
>  	struct aer_rpc *rpc;
>  	struct device *device = &dev->device;
>  
> +	if (type == PCI_EXP_TYPE_UPSTREAM || type == PCI_EXP_TYPE_DOWNSTREAM) {
> +		pci_enable_pcie_error_reporting(pdev);
> +		return 0;
> +	}

I think we need to either return an error in this case so that the
pcie_device won't be eligable for the .remove() callback, or add a
similiar type check in aer_remove().



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux