在 2018/10/11 23:57, Keith Busch 写道:
On Thu, Oct 11, 2018 at 08:26:18AM -0700, Bjorn Helgaas wrote:
From: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
Previously we enabled AER error reporting only for Switch Ports that were
enumerated prior to registering the AER service driver. Switch Ports
enumerated after AER driver registration were left with error reporting
disabled.
A common order, which works correctly, is that we enumerate devices before
registering portdrv and the AER driver:
- Enumerate all the devices at boot-time
- Register portdrv and bind it to all Root Ports and Switch Ports, which
disables error reporting for these Ports
- Register AER service driver and bind it to all Root Ports, which
enables error reporting for the Root Ports and any Switch Ports below
them
But if we enumerate devices *after* registering portdrv and the AER driver,
e.g., if a host bridge driver is loaded as a module, error reporting is not
enabled correctly:
- Register portdrv and AER driver (this happens at boot-time)
- Enumerate a Root Port
- Bind portdrv to Root Port, disabling its error reporting
- Bind AER service driver to Root Port, enabling error reporting for it
and its children (there are no children, since we haven't enumerated
them yet)
- Enumerate Switch Port below the Root Port
- Bind portdrv to Switch Port, disabling its error reporting
- AER service driver doesn't bind to Switch Ports, so error reporting
remains disabled
Hot-adding a Switch fails similarly: error reporting is enabled correctly
for the Root Port, but when the Switch is enumerated, the AER service
driver doesn't claim it, so there's nothing to enable error reporting for
the Switch Ports.
Change the AER service driver so it binds to *all* PCIe Ports, including
Switch Upstream and Downstream Ports. Enable AER error reporting for all
these Ports, but not for any children.
Link: https://lore.kernel.org/linux-pci/1536085989-2956-1-git-send-email-jonathan.derrick@xxxxxxxxx
Based-on-patch-by: Jon Derrick <jonathan.derrick@xxxxxxxxx>
Signed-off-by: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
---
drivers/pci/pcie/aer.c | 16 +++++++++-------
1 file changed, 9 insertions(+), 7 deletions(-)
diff --git a/drivers/pci/pcie/aer.c b/drivers/pci/pcie/aer.c
index 90b53abf621d..c40c6607849b 100644
--- a/drivers/pci/pcie/aer.c
+++ b/drivers/pci/pcie/aer.c
@@ -1316,12 +1316,6 @@ static void aer_enable_rootport(struct aer_rpc *rpc)
pci_read_config_dword(pdev, aer_pos + PCI_ERR_UNCOR_STATUS, ®32);
pci_write_config_dword(pdev, aer_pos + PCI_ERR_UNCOR_STATUS, reg32);
- /*
- * Enable error reporting for the root port device and downstream port
- * devices.
- */
- set_downstream_devices_error_reporting(pdev, true);
-
/* Enable Root Port's interrupt in response to error messages */
pci_read_config_dword(pdev, aer_pos + PCI_ERR_ROOT_COMMAND, ®32);
reg32 |= ROOT_PORT_INTR_ON_MESG_MASK;
@@ -1378,10 +1372,17 @@ static void aer_remove(struct pcie_device *dev)
*/
static int aer_probe(struct pcie_device *dev)
{
+ struct pci_dev *pdev = dev->port;
+ int type = pci_pcie_type(pdev);
int status;
struct aer_rpc *rpc;
struct device *device = &dev->device;
+ if (type == PCI_EXP_TYPE_UPSTREAM || type == PCI_EXP_TYPE_DOWNSTREAM) {
+ pci_enable_pcie_error_reporting(pdev);
+ return 0;
+ }
I think we need to either return an error in this case so that the
pcie_device won't be eligable for the .remove() callback, or add a
similiar type check in aer_remove().
It seems aer_root_reset() also will be called for downstream port(err.c driver->reset_link(dev)),
but aer_root_reset is only for root port.
static struct pcie_port_service_driver aerdriver = {
.name = "aer",
.port_type = PCIE_ANY_PORT,
.service = PCIE_PORT_SERVICE_AER,
.probe = aer_probe,
.remove = aer_remove,
.reset_link = aer_root_reset,
};
Thanks,
Dongdong
.
