On Wed, Jun 08, 2016 at 04:05:17PM +0800, Shawn Lin wrote:
> This patch adds a binding that describes the Rockchip PCIe controller
> found on Rockchip SoCs PCIe interface.
>
> Signed-off-by: Shawn Lin <shawn.lin@xxxxxxxxxxxxxx>
>
> ---
>
> Changes in v2:
> - fix lots clk/reset stuff suggested by Heiko
> - remove msi-parent and add msi-map suggested by Marc
> - drop phy related stuff
> - some others minor fixes
>
> .../devicetree/bindings/pci/rockchip-pcie.txt | 86 ++++++++++++++++++++++
> 1 file changed, 86 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt
>
> diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
> new file mode 100644
> index 0000000..eb92e29
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
> @@ -0,0 +1,86 @@
> +* Rockchip AXI PCIe Root Port Bridge DT description
> +
> +Required properties:
> +- #address-cells: Address representation for root ports, set to <3>
> +- #size-cells: Size representation for root ports, set to <2>
> +- #interrupt-cells: specifies the number of cells needed to encode an
> + interrupt source. The value must be 1.
> +- compatible: Should contain "rockchip,rk3399-pcie"
> +- reg: Two register ranges as listed in the reg-names property
> +- reg-names: Must include the following names
> + - "axi-base"
> + - "apb-base"
> +- clocks: Must contain an entry for each entry in clock-names.
> + See ../clocks/clock-bindings.txt for details.
> +- clock-names: Must include the following entries:
> + - "aclk"
> + - "aclk-perf"
> + - "hclk"
> + - "pm"
> +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe.
> +- phy-names: MUST be "pcie-phy".
phy-names is kind of pointless for 1 phy.
> +- interrupts: Three interrupt entries must be specified.
> +- interrupt-names: Must include the following names
> + - "sys"
> + - "legacy"
> + - "client"
> +- resets: Must contain five entries for each entry in reset-names.
> + See ../reset/reset.txt for details.
> +- reset-names: Must include the following names
> + - "core"
> + - "mgmt"
> + - "mgmt-sticky"
> + - "pipe"
> +- pinctrl-names : The pin control state names
> +- pinctrl-0: The "default" pinctrl state
> +- interrupt-map-mask and interrupt-map: standard PCI properties
> +- interrupt-controller: identifies the node as an interrupt controller
> +
> +Optional Property:
> +- ep-gpios: contain the entry for pre-reset gpio
> +- num-lanes: number of lanes to use
> +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie. If this
> + is specified we'll defer probe until we can find this regulator.
> +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie. If this
> + is specified we'll defer probe until we can find this regulator.
> +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie. If this
> + is specified we'll defer probe until we can find this regulator.
> +
> +Example:
> +
> +pcie0: pcie@f8000000 {
> + compatible = "rockchip,rk3399-pcie";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>,
> + <&cru PCLK_PCIE>;
> + clock-names = "aclk", "aclk-perf",
> + "hclk";
> + bus-range = <0x0 0x1>;
> + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names: "sys", "legacy", "client";
> + assigned-clocks = <&cru SCLK_PCIEPHY_REF>;
> + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>;
> + assigned-clock-rates = <100000000>;
> + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
> + ranges = < 0x82000000 0 0xfa000000 0x0 0xfa000000 0 0x600000
> + 0x81000000 0 0xfa600000 0x0 0xfa600000 0 0x100000 >;
No 64-bit memory space?
> + num-lanes = <4>;
> + reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >;
> + reg-name = "axi-base", "apb-base";
> + resets = <&cru SRST_PCIEPHY>, <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>,
> + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>;
> + reset-names = "core", "mgmt", "mgmt-sticky", "pipe";
> + phys = <&pcie_phy>;
> + phy-names = "pcie-phy";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie_clkreq>;
> + #interrupt-cells = <1>;
> + interrupt-controller;
> + interrupt-map-mask = <0 0 0 7>;
> + interrupt-map = <0 0 0 1 &pcie0 1>,
> + <0 0 0 2 &pcie0 2>,
> + <0 0 0 3 &pcie0 3>,
> + <0 0 0 4 &pcie0 4>;
> +};
> --
> 2.3.7
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
