On 08/06/16 09:05, Shawn Lin wrote: > This patch adds a binding that describes the Rockchip PCIe controller > found on Rockchip SoCs PCIe interface. > > Signed-off-by: Shawn Lin <shawn.lin@xxxxxxxxxxxxxx> > > --- > > Changes in v2: > - fix lots clk/reset stuff suggested by Heiko > - remove msi-parent and add msi-map suggested by Marc > - drop phy related stuff > - some others minor fixes > > .../devicetree/bindings/pci/rockchip-pcie.txt | 86 ++++++++++++++++++++++ > 1 file changed, 86 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt > > diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt > new file mode 100644 > index 0000000..eb92e29 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt > @@ -0,0 +1,86 @@ > +* Rockchip AXI PCIe Root Port Bridge DT description > + > +Required properties: > +- #address-cells: Address representation for root ports, set to <3> > +- #size-cells: Size representation for root ports, set to <2> > +- #interrupt-cells: specifies the number of cells needed to encode an > + interrupt source. The value must be 1. > +- compatible: Should contain "rockchip,rk3399-pcie" > +- reg: Two register ranges as listed in the reg-names property > +- reg-names: Must include the following names > + - "axi-base" > + - "apb-base" > +- clocks: Must contain an entry for each entry in clock-names. > + See ../clocks/clock-bindings.txt for details. > +- clock-names: Must include the following entries: > + - "aclk" > + - "aclk-perf" > + - "hclk" > + - "pm" > +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. > +- phy-names: MUST be "pcie-phy". > +- interrupts: Three interrupt entries must be specified. > +- interrupt-names: Must include the following names > + - "sys" > + - "legacy" > + - "client" > +- resets: Must contain five entries for each entry in reset-names. > + See ../reset/reset.txt for details. > +- reset-names: Must include the following names > + - "core" > + - "mgmt" > + - "mgmt-sticky" > + - "pipe" > +- pinctrl-names : The pin control state names > +- pinctrl-0: The "default" pinctrl state > +- interrupt-map-mask and interrupt-map: standard PCI properties > +- interrupt-controller: identifies the node as an interrupt controller > + > +Optional Property: > +- ep-gpios: contain the entry for pre-reset gpio > +- num-lanes: number of lanes to use > +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. > +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. > +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie. If this > + is specified we'll defer probe until we can find this regulator. Please do not describe the behaviour of the driver here. Thanks, M. -- Jazz is not dead. It just smells funny... -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
