This patch adds a binding that describes the Rockchip PCIe controller
found on Rockchip SoCs PCIe interface.
Signed-off-by: Shawn Lin <shawn.lin@xxxxxxxxxxxxxx>
---
Changes in v2:
- fix lots clk/reset stuff suggested by Heiko
- remove msi-parent and add msi-map suggested by Marc
- drop phy related stuff
- some others minor fixes
.../devicetree/bindings/pci/rockchip-pcie.txt | 86 ++++++++++++++++++++++
1 file changed, 86 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt
diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
new file mode 100644
index 0000000..eb92e29
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
@@ -0,0 +1,86 @@
+* Rockchip AXI PCIe Root Port Bridge DT description
+
+Required properties:
+- #address-cells: Address representation for root ports, set to <3>
+- #size-cells: Size representation for root ports, set to <2>
+- #interrupt-cells: specifies the number of cells needed to encode an
+ interrupt source. The value must be 1.
+- compatible: Should contain "rockchip,rk3399-pcie"
+- reg: Two register ranges as listed in the reg-names property
+- reg-names: Must include the following names
+ - "axi-base"
+ - "apb-base"
+- clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+ - "aclk"
+ - "aclk-perf"
+ - "hclk"
+ - "pm"
+- phys: From PHY bindings: Phandle for the Generic PHY for PCIe.
+- phy-names: MUST be "pcie-phy".
+- interrupts: Three interrupt entries must be specified.
+- interrupt-names: Must include the following names
+ - "sys"
+ - "legacy"
+ - "client"
+- resets: Must contain five entries for each entry in reset-names.
+ See ../reset/reset.txt for details.
+- reset-names: Must include the following names
+ - "core"
+ - "mgmt"
+ - "mgmt-sticky"
+ - "pipe"
+- pinctrl-names : The pin control state names
+- pinctrl-0: The "default" pinctrl state
+- interrupt-map-mask and interrupt-map: standard PCI properties
+- interrupt-controller: identifies the node as an interrupt controller
+
+Optional Property:
+- ep-gpios: contain the entry for pre-reset gpio
+- num-lanes: number of lanes to use
+- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie. If this
+ is specified we'll defer probe until we can find this regulator.
+- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie. If this
+ is specified we'll defer probe until we can find this regulator.
+- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie. If this
+ is specified we'll defer probe until we can find this regulator.
+
+Example:
+
+pcie0: pcie@f8000000 {
+ compatible = "rockchip,rk3399-pcie";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>,
+ <&cru PCLK_PCIE>;
+ clock-names = "aclk", "aclk-perf",
+ "hclk";
+ bus-range = <0x0 0x1>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names: "sys", "legacy", "client";
+ assigned-clocks = <&cru SCLK_PCIEPHY_REF>;
+ assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>;
+ assigned-clock-rates = <100000000>;
+ ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+ ranges = < 0x82000000 0 0xfa000000 0x0 0xfa000000 0 0x600000
+ 0x81000000 0 0xfa600000 0x0 0xfa600000 0 0x100000 >;
+ num-lanes = <4>;
+ reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >;
+ reg-name = "axi-base", "apb-base";
+ resets = <&cru SRST_PCIEPHY>, <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>,
+ <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>;
+ reset-names = "core", "mgmt", "mgmt-sticky", "pipe";
+ phys = <&pcie_phy>;
+ phy-names = "pcie-phy";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_clkreq>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie0 1>,
+ <0 0 0 2 &pcie0 2>,
+ <0 0 0 3 &pcie0 3>,
+ <0 0 0 4 &pcie0 4>;
+};
--
2.3.7
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
