> On Tue, Feb 27, 2024 at 06:35:20PM +0800, Minda Chen wrote:
> > Add StarFive JH7110 SoC PCIe controller platform driver codes, JH7110
> > with PLDA host PCIe core.
> >
> > Signed-off-by: Minda Chen <minda.chen@xxxxxxxxxxxxxxxx>
> > Co-developed-by: Kevin Xie <kevin.xie@xxxxxxxxxxxxxxxx>
> > Reviewed-by: Mason Huo <mason.huo@xxxxxxxxxxxxxxxx>
> > ---
> > MAINTAINERS | 7 +
> > drivers/pci/controller/plda/Kconfig | 12 +
> > drivers/pci/controller/plda/Makefile | 1 +
> > drivers/pci/controller/plda/pcie-plda.h | 71 ++-
> > drivers/pci/controller/plda/pcie-starfive.c | 473
> > ++++++++++++++++++++
> > 5 files changed, 563 insertions(+), 1 deletion(-) create mode 100644
> > drivers/pci/controller/plda/pcie-starfive.c
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS index
> > fc9576e69a71..d3b0a0fb754f 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -17078,6 +17078,13 @@ S: Maintained
> > F: Documentation/devicetree/bindings/pci/socionext,uniphier-pcie*
> > F: drivers/pci/controller/dwc/pcie-uniphier*
> >
> > +PCIE DRIVER FOR STARFIVE JH71x0
> > +M: Kevin Xie <kevin.xie@xxxxxxxxxxxxxxxx>
> > +L: linux-pci@xxxxxxxxxxxxxxx
> > +S: Maintained
> > +F: Documentation/devicetree/bindings/pci/starfive*
> > +F: drivers/pci/controller/plda/pcie-starfive.c
> > +
> > PCIE DRIVER FOR ST SPEAR13XX
> > M: Pratyush Anand <pratyush.anand@xxxxxxxxx>
> > L: linux-pci@xxxxxxxxxxxxxxx
> > diff --git a/drivers/pci/controller/plda/pcie-plda.h
> > b/drivers/pci/controller/plda/pcie-plda.h
> > index 7b69891700a4..04e385758a2f 100644
> > --- a/drivers/pci/controller/plda/pcie-plda.h
> > +++ b/drivers/pci/controller/plda/pcie-plda.h
> > @@ -10,10 +10,20 @@
> > #define PLDA_MAX_NUM_MSI_IRQS 32
> >
> > /* PCIe Bridge Phy Regs */
> > +#define GEN_SETTINGS 0x80
> > +#define RP_ENABLE 1
> > +#define PCIE_PCI_IDS_DW1 0x9c
> > +#define IDS_CLASS_CODE_SHIFT 16
> > +#define REVISION_ID_MASK GENMASK(7, 0)
> > +#define CLASS_CODE_ID_MASK GENMASK(31, 8)
> > #define PCIE_PCI_IRQ_DW0 0xa8
> > #define MSIX_CAP_MASK BIT(31)
> > #define NUM_MSI_MSGS_MASK GENMASK(6, 4)
> > #define NUM_MSI_MSGS_SHIFT 4
> > +#define PCI_MISC 0xb4
> > +#define PHY_FUNCTION_DIS BIT(15)
> > +#define PCIE_WINROM 0xfc
> > +#define PREF_MEM_WIN_64_SUPPORT BIT(3)
> >
> > #define IMASK_LOCAL 0x180
> > #define DMA_END_ENGINE_0_MASK 0x00000000u
> > @@ -65,6 +75,8 @@
> > #define ISTATUS_HOST 0x18c
> > #define IMSI_ADDR 0x190
> > #define ISTATUS_MSI 0x194
> > +#define PMSG_SUPPORT_RX 0x3f0
> > +#define PMSG_LTR_SUPPORT BIT(2)
> >
> > /* PCIe Master table init defines */
> > #define ATR0_PCIE_WIN0_SRCADDR_PARAM 0x600u
> > @@ -86,6 +98,8 @@
> > #define PCIE_TX_RX_INTERFACE 0x00000000u
> > #define PCIE_CONFIG_INTERFACE 0x00000001u
> >
> > +#define CONFIG_SPACE_ADDR_OFFSET 0x1000u
> > +
> > #define ATR_ENTRY_SIZE 32
> >
> > enum plda_int_event {
> > @@ -200,4 +214,59 @@ static inline void plda_set_default_msi(struct
> plda_msi *msi)
> > msi->vector_phy = IMSI_ADDR;
> > msi->num_vectors = PLDA_MAX_NUM_MSI_IRQS; } -#endif
> > +
> > +static inline void plda_pcie_enable_root_port(struct plda_pcie_rp
> > +*plda) {
> > + u32 value;
> > +
> > + value = readl_relaxed(plda->bridge_addr + GEN_SETTINGS);
> > + value |= RP_ENABLE;
> > + writel_relaxed(value, plda->bridge_addr + GEN_SETTINGS); }
> > +
> > +static inline void plda_pcie_set_standard_class(struct plda_pcie_rp
> > +*plda) {
> > + u32 value;
> > +
> > + /* set class code and reserve revision id */
> > + value = readl_relaxed(plda->bridge_addr + PCIE_PCI_IDS_DW1);
> > + value &= REVISION_ID_MASK;
> > + value |= (PCI_CLASS_BRIDGE_PCI << IDS_CLASS_CODE_SHIFT);
> > + writel_relaxed(value, plda->bridge_addr + PCIE_PCI_IDS_DW1); }
> > +
> > +static inline void plda_pcie_set_pref_win_64bit(struct plda_pcie_rp
> > +*plda) {
> > + u32 value;
> > +
> > + value = readl_relaxed(plda->bridge_addr + PCIE_WINROM);
> > + value |= PREF_MEM_WIN_64_SUPPORT;
> > + writel_relaxed(value, plda->bridge_addr + PCIE_WINROM); }
>
> What does this do ?
>
This is an internal register to enable the prefetchable memory window
64-bit addressing support. ( disabled by default)
After this enable configuration, the address translation config in DTS
and ATU about 64-bit prefetchable memory are useful.
I will add the annotation here in the next version.
> > +static inline void plda_pcie_disable_ltr(struct plda_pcie_rp *plda) {
> > + u32 value;
> > +
> > + value = readl_relaxed(plda->bridge_addr + PMSG_SUPPORT_RX);
> > + value &= ~PMSG_LTR_SUPPORT;
> > + writel_relaxed(value, plda->bridge_addr + PMSG_SUPPORT_RX); }
> > +
> > +static inline void plda_pcie_disable_func(struct plda_pcie_rp *plda)
> > +{
> > + u32 value;
> > +
> > + value = readl_relaxed(plda->bridge_addr + PCI_MISC);
> > + value |= PHY_FUNCTION_DIS;
> > + writel_relaxed(value, plda->bridge_addr + PCI_MISC); }
> > +
> > +static inline void plda_pcie_write_rc_bar(struct plda_pcie_rp *plda,
> > +u64 val) {
> > + void __iomem *addr = plda->bridge_addr +
> CONFIG_SPACE_ADDR_OFFSET;
> > +
> > + writel_relaxed(lower_32_bits(val), addr + PCI_BASE_ADDRESS_0);
> > + writel_relaxed(upper_32_bits(val), addr + PCI_BASE_ADDRESS_1); }
> > +#endif /* _PCIE_PLDA_H */
> > diff --git a/drivers/pci/controller/plda/pcie-starfive.c
> > b/drivers/pci/controller/plda/pcie-starfive.c
> > new file mode 100644
> > index 000000000000..9bb9f0e29565
> > --- /dev/null
> > +++ b/drivers/pci/controller/plda/pcie-starfive.c
> > @@ -0,0 +1,473 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * PCIe host controller driver for StarFive JH7110 Soc.
> > + *
> > + * Copyright (C) 2023 StarFive Technology Co., Ltd.
> > + */
> > +
> > +#include <linux/bitfield.h>
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/kernel.h>
> > +#include <linux/mfd/syscon.h>
> > +#include <linux/module.h>
> > +#include <linux/of_address.h>
> > +#include <linux/of_irq.h>
> > +#include <linux/of_pci.h>
> > +#include <linux/pci.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/regmap.h>
> > +#include <linux/reset.h>
> > +#include "../../pci.h"
> > +
> > +#include "pcie-plda.h"
> > +
> > +#define PCIE_FUNC_NUM 4
> > +
> > +/* system control */
> > +#define STG_SYSCON_PCIE0_BASE 0x48
> > +#define STG_SYSCON_PCIE1_BASE 0x1f8
> > +
> > +#define STG_SYSCON_AR_OFFSET 0x78
> > +#define STG_SYSCON_AXI4_SLVL_AR_MASK GENMASK(22, 8)
> > +#define STG_SYSCON_AXI4_SLVL_PHY_AR(x)
> FIELD_PREP(GENMASK(20, 17), x)
> > +#define STG_SYSCON_AW_OFFSET 0x7c
> > +#define STG_SYSCON_AXI4_SLVL_AW_MASK GENMASK(14, 0)
> > +#define STG_SYSCON_AXI4_SLVL_PHY_AW(x)
> FIELD_PREP(GENMASK(12, 9), x)
> > +#define STG_SYSCON_CLKREQ BIT(22)
> > +#define STG_SYSCON_CKREF_SRC_MASK GENMASK(19, 18)
> > +#define STG_SYSCON_RP_NEP_OFFSET 0xe8
> > +#define STG_SYSCON_K_RP_NEP BIT(8)
> > +#define STG_SYSCON_LNKSTA_OFFSET 0x170
> > +#define DATA_LINK_ACTIVE BIT(5)
> > +
> > +/* Parameters for the waiting for link up routine */
> > +#define LINK_WAIT_MAX_RETRIES 10
> > +#define LINK_WAIT_USLEEP_MIN 90000
> > +#define LINK_WAIT_USLEEP_MAX 100000
> > +
> > +struct starfive_jh7110_pcie {
> > + struct plda_pcie_rp plda;
> > + struct reset_control *resets;
> > + struct clk_bulk_data *clks;
> > + struct regmap *reg_syscon;
> > + struct gpio_desc *power_gpio;
> > + struct gpio_desc *reset_gpio;
> > + struct phy *phy;
> > +
> > + unsigned int stg_pcie_base;
> > + int num_clks;
> > +};
> > +
> > +/*
> > + * The BAR0/1 of bridge should be hidden during enumeration to
> > + * avoid the sizing and resource allocation by PCIe core.
>
> Please explain. This is what's preventing this driver to re-use the
> PCI_HOST_COMMON infrastructure and it is unclear why.
>
Sorry, we didn't explain it clearly enough here.
JH7110 PCIe port BAR0/1 is configured as 64-bit prefetchable memory
space, PCIe read and write requests targeting BAR0/1 are routed to so
called 'Bridge Configuration space' in PLDA datasheet, which contains
the bridge internal registers, such as interrupt, DMA & ATU registers...
JH7110 can access the Bridge Configuration space by local bus, and don`t
want the bridge internal registers accessed by the DMA from EP devices.
Thus, they are unimplemented and should be hidden.
I will modify the annotation in next version if you think it is ok.
> > + */
> > +static bool starfive_pcie_hide_rc_bar(struct pci_bus *bus, unsigned int
> devfn,
> > + int offset)
> > +{
> > + if (pci_is_root_bus(bus) && !devfn &&
> > + (offset == PCI_BASE_ADDRESS_0 || offset == PCI_BASE_ADDRESS_1))
> > + return true;
> > +
> > + return false;
> > +}
> > +
> > +static int starfive_pcie_config_write(struct pci_bus *bus, unsigned int devfn,
> > + int where, int size, u32 value) {
> > + if (starfive_pcie_hide_rc_bar(bus, devfn, where))
> > + return PCIBIOS_SUCCESSFUL;
> > +
> > + return pci_generic_config_write(bus, devfn, where, size, value); }
> > +
> > +static int starfive_pcie_config_read(struct pci_bus *bus, unsigned int devfn,
> > + int where, int size, u32 *value) {
> > + if (starfive_pcie_hide_rc_bar(bus, devfn, where)) {
> > + *value = 0;
> > + return PCIBIOS_SUCCESSFUL;
> > + }
> > +
> > + return pci_generic_config_read(bus, devfn, where, size, value); }
> > +
> > +static int starfive_pcie_parse_dt(struct starfive_jh7110_pcie *pcie,
> > + struct device *dev)
> > +{
> > + int domain_nr;
> > +
> > + pcie->num_clks = devm_clk_bulk_get_all(dev, &pcie->clks);
> > + if (pcie->num_clks < 0)
> > + return dev_err_probe(dev, pcie->num_clks,
> > + "failed to get pcie clocks\n");
> > +
> > + pcie->resets = devm_reset_control_array_get_exclusive(dev);
> > + if (IS_ERR(pcie->resets))
> > + return dev_err_probe(dev, PTR_ERR(pcie->resets),
> > + "failed to get pcie resets");
> > +
> > + pcie->reg_syscon =
> > + syscon_regmap_lookup_by_phandle(dev->of_node,
> > + "starfive,stg-syscon");
> > +
> > + if (IS_ERR(pcie->reg_syscon))
> > + return dev_err_probe(dev, PTR_ERR(pcie->reg_syscon),
> > + "failed to parse starfive,stg-syscon\n");
> > +
> > + pcie->phy = devm_phy_optional_get(dev, NULL);
> > + if (IS_ERR(pcie->phy))
> > + return dev_err_probe(dev, PTR_ERR(pcie->phy),
> > + "failed to get pcie phy\n");
> > +
> > + domain_nr = of_get_pci_domain_nr(dev->of_node);
> > +
> > + if (domain_nr < 0 || domain_nr > 1)
> > + return dev_err_probe(dev, -ENODEV,
> > + "failed to get valid pcie domain\n");
> > +
> > + if (domain_nr == 0)
> > + pcie->stg_pcie_base = STG_SYSCON_PCIE0_BASE;
> > + else
> > + pcie->stg_pcie_base = STG_SYSCON_PCIE1_BASE;
>
> I don't agree with this. The domain number is a software allocated value
> attached to a controller. It is written nowhere that you can't swap them and
> leave this code path broken.
>
We set 'linux,pci-domain = <0>' in our pcie0 DTS node, and <1> for
pcie1. The value should be static now.
As the STG system controller defines different bases in PCIe RP0 & RP1,
we have to identify which controller is doing the hardware initialization.
We discussed this before with other maintainers, do you have a better
suggestion?
> > + pcie->reset_gpio = devm_gpiod_get_optional(dev, "perst",
> > + GPIOD_OUT_HIGH);
> > + if (IS_ERR(pcie->reset_gpio))
> > + return dev_err_probe(dev, PTR_ERR(pcie->reset_gpio),
> > + "failed to get perst-gpio\n");
> > +
> > + pcie->power_gpio = devm_gpiod_get_optional(dev, "enable",
> > + GPIOD_OUT_LOW);
> > + if (IS_ERR(pcie->power_gpio))
> > + return dev_err_probe(dev, PTR_ERR(pcie->power_gpio),
> > + "failed to get power-gpio\n");
> > +
> > + return 0;
> > +}
> > +
> > +static struct pci_ops starfive_pcie_ops = {
> > + .map_bus = plda_pcie_map_bus,
>
> It looks like this is an ECAM driver with the read/config quirks for read/write in
> the method below. Please explain why they are needed.
>
Yes, that's for the hide RC BAR operations mentioned above.
> > + .read = starfive_pcie_config_read,
> > + .write = starfive_pcie_config_write,
> > +};
> > +
> > +static int starfive_pcie_clk_rst_init(struct starfive_jh7110_pcie
> > +*pcie) {
> > + struct device *dev = pcie->plda.dev;
> > + int ret;
> > +
> > + /* PCIe PCI Standard Configuration Identification Settings. */
> > + plda_pcie_set_standard_class(plda);
> > +
> > + /*
> > + * The LTR message forwarding of PCIe Message Reception was set by
> > +core
>
> "LTR message forwarding of PCIe Message Reception".
>
> What is this referring to ?
>
Sorry, this sentence is ambiguous.
"PCIe Message Reception" is a register to enable the function about forwarding
specific PCIe messages to AXI application, such as ATS/LTR/OBFF messages...
Here we clear bit 2 to disable the LTR message forwarding to the AXI application.
I will modify the annotation in next version if you think it is ok.
Thank you for your valuable comments.
Kevin.
> Thanks,
> Lorenzo
>
> > + * as default, but the forward id & addr are also need to be reset.
> > + * If we do not disable LTR message forwarding here, or set a legal
> > + * forwarding address, the kernel will get stuck after the driver probe.
> > + * To workaround, disable the LTR message forwarding support on
> > + * PCIe Message Reception.
> > + */
> > + plda_pcie_disable_ltr(plda);
> > +
> > + /* Prefetchable memory window 64-bit addressing support */
> > + plda_pcie_set_pref_win_64bit(plda);
> > +
> >
> > _______________________________________________
> > linux-riscv mailing list
> > linux-riscv@xxxxxxxxxxxxxxxxxxx
> > http://lists.infradead.org/mailman/listinfo/linux-riscv
