On Tue, Feb 27, 2024 at 06:35:20PM +0800, Minda Chen wrote:
> Add StarFive JH7110 SoC PCIe controller platform driver codes, JH7110
> with PLDA host PCIe core.
>
> Signed-off-by: Minda Chen <minda.chen@xxxxxxxxxxxxxxxx>
> Co-developed-by: Kevin Xie <kevin.xie@xxxxxxxxxxxxxxxx>
> Reviewed-by: Mason Huo <mason.huo@xxxxxxxxxxxxxxxx>
> ---
> MAINTAINERS | 7 +
> drivers/pci/controller/plda/Kconfig | 12 +
> drivers/pci/controller/plda/Makefile | 1 +
> drivers/pci/controller/plda/pcie-plda.h | 71 ++-
> drivers/pci/controller/plda/pcie-starfive.c | 473 ++++++++++++++++++++
> 5 files changed, 563 insertions(+), 1 deletion(-)
> create mode 100644 drivers/pci/controller/plda/pcie-starfive.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index fc9576e69a71..d3b0a0fb754f 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -17078,6 +17078,13 @@ S: Maintained
> F: Documentation/devicetree/bindings/pci/socionext,uniphier-pcie*
> F: drivers/pci/controller/dwc/pcie-uniphier*
>
> +PCIE DRIVER FOR STARFIVE JH71x0
> +M: Kevin Xie <kevin.xie@xxxxxxxxxxxxxxxx>
> +L: linux-pci@xxxxxxxxxxxxxxx
> +S: Maintained
> +F: Documentation/devicetree/bindings/pci/starfive*
> +F: drivers/pci/controller/plda/pcie-starfive.c
> +
> PCIE DRIVER FOR ST SPEAR13XX
> M: Pratyush Anand <pratyush.anand@xxxxxxxxx>
> L: linux-pci@xxxxxxxxxxxxxxx
> diff --git a/drivers/pci/controller/plda/Kconfig b/drivers/pci/controller/plda/Kconfig
> index e54a82ee94f5..c0e14146d7e4 100644
> --- a/drivers/pci/controller/plda/Kconfig
> +++ b/drivers/pci/controller/plda/Kconfig
> @@ -15,4 +15,16 @@ config PCIE_MICROCHIP_HOST
> Say Y here if you want kernel to support the Microchip AXI PCIe
> Host Bridge driver.
>
> +config PCIE_STARFIVE_HOST
> + tristate "StarFive PCIe host controller"
> + depends on PCI_MSI && OF
> + depends on ARCH_STARFIVE || COMPILE_TEST
> + select PCIE_PLDA_HOST
> + help
> + Say Y here if you want to support the StarFive PCIe controller in
> + host mode. StarFive PCIe controller uses PLDA PCIe core.
> +
> + If you choose to build this driver as module it will be dynamically
> + linked and module will be called pcie-starfive.ko.
> +
> endmenu
> diff --git a/drivers/pci/controller/plda/Makefile b/drivers/pci/controller/plda/Makefile
> index 4340ab007f44..0ac6851bed48 100644
> --- a/drivers/pci/controller/plda/Makefile
> +++ b/drivers/pci/controller/plda/Makefile
> @@ -1,3 +1,4 @@
> # SPDX-License-Identifier: GPL-2.0
> obj-$(CONFIG_PCIE_PLDA_HOST) += pcie-plda-host.o
> obj-$(CONFIG_PCIE_MICROCHIP_HOST) += pcie-microchip-host.o
> +obj-$(CONFIG_PCIE_STARFIVE_HOST) += pcie-starfive.o
> diff --git a/drivers/pci/controller/plda/pcie-plda.h b/drivers/pci/controller/plda/pcie-plda.h
> index 7b69891700a4..04e385758a2f 100644
> --- a/drivers/pci/controller/plda/pcie-plda.h
> +++ b/drivers/pci/controller/plda/pcie-plda.h
> @@ -10,10 +10,20 @@
> #define PLDA_MAX_NUM_MSI_IRQS 32
>
> /* PCIe Bridge Phy Regs */
> +#define GEN_SETTINGS 0x80
> +#define RP_ENABLE 1
> +#define PCIE_PCI_IDS_DW1 0x9c
> +#define IDS_CLASS_CODE_SHIFT 16
> +#define REVISION_ID_MASK GENMASK(7, 0)
> +#define CLASS_CODE_ID_MASK GENMASK(31, 8)
> #define PCIE_PCI_IRQ_DW0 0xa8
> #define MSIX_CAP_MASK BIT(31)
> #define NUM_MSI_MSGS_MASK GENMASK(6, 4)
> #define NUM_MSI_MSGS_SHIFT 4
> +#define PCI_MISC 0xb4
> +#define PHY_FUNCTION_DIS BIT(15)
> +#define PCIE_WINROM 0xfc
> +#define PREF_MEM_WIN_64_SUPPORT BIT(3)
>
> #define IMASK_LOCAL 0x180
> #define DMA_END_ENGINE_0_MASK 0x00000000u
> @@ -65,6 +75,8 @@
> #define ISTATUS_HOST 0x18c
> #define IMSI_ADDR 0x190
> #define ISTATUS_MSI 0x194
> +#define PMSG_SUPPORT_RX 0x3f0
> +#define PMSG_LTR_SUPPORT BIT(2)
>
> /* PCIe Master table init defines */
> #define ATR0_PCIE_WIN0_SRCADDR_PARAM 0x600u
> @@ -86,6 +98,8 @@
> #define PCIE_TX_RX_INTERFACE 0x00000000u
> #define PCIE_CONFIG_INTERFACE 0x00000001u
>
> +#define CONFIG_SPACE_ADDR_OFFSET 0x1000u
> +
> #define ATR_ENTRY_SIZE 32
>
> enum plda_int_event {
> @@ -200,4 +214,59 @@ static inline void plda_set_default_msi(struct plda_msi *msi)
> msi->vector_phy = IMSI_ADDR;
> msi->num_vectors = PLDA_MAX_NUM_MSI_IRQS;
> }
> -#endif
> +
> +static inline void plda_pcie_enable_root_port(struct plda_pcie_rp *plda)
> +{
> + u32 value;
> +
> + value = readl_relaxed(plda->bridge_addr + GEN_SETTINGS);
> + value |= RP_ENABLE;
> + writel_relaxed(value, plda->bridge_addr + GEN_SETTINGS);
> +}
> +
> +static inline void plda_pcie_set_standard_class(struct plda_pcie_rp *plda)
> +{
> + u32 value;
> +
> + /* set class code and reserve revision id */
> + value = readl_relaxed(plda->bridge_addr + PCIE_PCI_IDS_DW1);
> + value &= REVISION_ID_MASK;
> + value |= (PCI_CLASS_BRIDGE_PCI << IDS_CLASS_CODE_SHIFT);
> + writel_relaxed(value, plda->bridge_addr + PCIE_PCI_IDS_DW1);
> +}
> +
> +static inline void plda_pcie_set_pref_win_64bit(struct plda_pcie_rp *plda)
> +{
> + u32 value;
> +
> + value = readl_relaxed(plda->bridge_addr + PCIE_WINROM);
> + value |= PREF_MEM_WIN_64_SUPPORT;
> + writel_relaxed(value, plda->bridge_addr + PCIE_WINROM);
> +}
What does this do ?
> +static inline void plda_pcie_disable_ltr(struct plda_pcie_rp *plda)
> +{
> + u32 value;
> +
> + value = readl_relaxed(plda->bridge_addr + PMSG_SUPPORT_RX);
> + value &= ~PMSG_LTR_SUPPORT;
> + writel_relaxed(value, plda->bridge_addr + PMSG_SUPPORT_RX);
> +}
> +
> +static inline void plda_pcie_disable_func(struct plda_pcie_rp *plda)
> +{
> + u32 value;
> +
> + value = readl_relaxed(plda->bridge_addr + PCI_MISC);
> + value |= PHY_FUNCTION_DIS;
> + writel_relaxed(value, plda->bridge_addr + PCI_MISC);
> +}
> +
> +static inline void plda_pcie_write_rc_bar(struct plda_pcie_rp *plda, u64 val)
> +{
> + void __iomem *addr = plda->bridge_addr + CONFIG_SPACE_ADDR_OFFSET;
> +
> + writel_relaxed(lower_32_bits(val), addr + PCI_BASE_ADDRESS_0);
> + writel_relaxed(upper_32_bits(val), addr + PCI_BASE_ADDRESS_1);
> +}
> +#endif /* _PCIE_PLDA_H */
> diff --git a/drivers/pci/controller/plda/pcie-starfive.c b/drivers/pci/controller/plda/pcie-starfive.c
> new file mode 100644
> index 000000000000..9bb9f0e29565
> --- /dev/null
> +++ b/drivers/pci/controller/plda/pcie-starfive.c
> @@ -0,0 +1,473 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * PCIe host controller driver for StarFive JH7110 Soc.
> + *
> + * Copyright (C) 2023 StarFive Technology Co., Ltd.
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_pci.h>
> +#include <linux/pci.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include "../../pci.h"
> +
> +#include "pcie-plda.h"
> +
> +#define PCIE_FUNC_NUM 4
> +
> +/* system control */
> +#define STG_SYSCON_PCIE0_BASE 0x48
> +#define STG_SYSCON_PCIE1_BASE 0x1f8
> +
> +#define STG_SYSCON_AR_OFFSET 0x78
> +#define STG_SYSCON_AXI4_SLVL_AR_MASK GENMASK(22, 8)
> +#define STG_SYSCON_AXI4_SLVL_PHY_AR(x) FIELD_PREP(GENMASK(20, 17), x)
> +#define STG_SYSCON_AW_OFFSET 0x7c
> +#define STG_SYSCON_AXI4_SLVL_AW_MASK GENMASK(14, 0)
> +#define STG_SYSCON_AXI4_SLVL_PHY_AW(x) FIELD_PREP(GENMASK(12, 9), x)
> +#define STG_SYSCON_CLKREQ BIT(22)
> +#define STG_SYSCON_CKREF_SRC_MASK GENMASK(19, 18)
> +#define STG_SYSCON_RP_NEP_OFFSET 0xe8
> +#define STG_SYSCON_K_RP_NEP BIT(8)
> +#define STG_SYSCON_LNKSTA_OFFSET 0x170
> +#define DATA_LINK_ACTIVE BIT(5)
> +
> +/* Parameters for the waiting for link up routine */
> +#define LINK_WAIT_MAX_RETRIES 10
> +#define LINK_WAIT_USLEEP_MIN 90000
> +#define LINK_WAIT_USLEEP_MAX 100000
> +
> +struct starfive_jh7110_pcie {
> + struct plda_pcie_rp plda;
> + struct reset_control *resets;
> + struct clk_bulk_data *clks;
> + struct regmap *reg_syscon;
> + struct gpio_desc *power_gpio;
> + struct gpio_desc *reset_gpio;
> + struct phy *phy;
> +
> + unsigned int stg_pcie_base;
> + int num_clks;
> +};
> +
> +/*
> + * The BAR0/1 of bridge should be hidden during enumeration to
> + * avoid the sizing and resource allocation by PCIe core.
Please explain. This is what's preventing this driver to re-use
the PCI_HOST_COMMON infrastructure and it is unclear why.
> + */
> +static bool starfive_pcie_hide_rc_bar(struct pci_bus *bus, unsigned int devfn,
> + int offset)
> +{
> + if (pci_is_root_bus(bus) && !devfn &&
> + (offset == PCI_BASE_ADDRESS_0 || offset == PCI_BASE_ADDRESS_1))
> + return true;
> +
> + return false;
> +}
> +
> +static int starfive_pcie_config_write(struct pci_bus *bus, unsigned int devfn,
> + int where, int size, u32 value)
> +{
> + if (starfive_pcie_hide_rc_bar(bus, devfn, where))
> + return PCIBIOS_SUCCESSFUL;
> +
> + return pci_generic_config_write(bus, devfn, where, size, value);
> +}
> +
> +static int starfive_pcie_config_read(struct pci_bus *bus, unsigned int devfn,
> + int where, int size, u32 *value)
> +{
> + if (starfive_pcie_hide_rc_bar(bus, devfn, where)) {
> + *value = 0;
> + return PCIBIOS_SUCCESSFUL;
> + }
> +
> + return pci_generic_config_read(bus, devfn, where, size, value);
> +}
> +
> +static int starfive_pcie_parse_dt(struct starfive_jh7110_pcie *pcie,
> + struct device *dev)
> +{
> + int domain_nr;
> +
> + pcie->num_clks = devm_clk_bulk_get_all(dev, &pcie->clks);
> + if (pcie->num_clks < 0)
> + return dev_err_probe(dev, pcie->num_clks,
> + "failed to get pcie clocks\n");
> +
> + pcie->resets = devm_reset_control_array_get_exclusive(dev);
> + if (IS_ERR(pcie->resets))
> + return dev_err_probe(dev, PTR_ERR(pcie->resets),
> + "failed to get pcie resets");
> +
> + pcie->reg_syscon =
> + syscon_regmap_lookup_by_phandle(dev->of_node,
> + "starfive,stg-syscon");
> +
> + if (IS_ERR(pcie->reg_syscon))
> + return dev_err_probe(dev, PTR_ERR(pcie->reg_syscon),
> + "failed to parse starfive,stg-syscon\n");
> +
> + pcie->phy = devm_phy_optional_get(dev, NULL);
> + if (IS_ERR(pcie->phy))
> + return dev_err_probe(dev, PTR_ERR(pcie->phy),
> + "failed to get pcie phy\n");
> +
> + domain_nr = of_get_pci_domain_nr(dev->of_node);
> +
> + if (domain_nr < 0 || domain_nr > 1)
> + return dev_err_probe(dev, -ENODEV,
> + "failed to get valid pcie domain\n");
> +
> + if (domain_nr == 0)
> + pcie->stg_pcie_base = STG_SYSCON_PCIE0_BASE;
> + else
> + pcie->stg_pcie_base = STG_SYSCON_PCIE1_BASE;
I don't agree with this. The domain number is a software allocated
value attached to a controller. It is written nowhere that you can't
swap them and leave this code path broken.
> + pcie->reset_gpio = devm_gpiod_get_optional(dev, "perst",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(pcie->reset_gpio))
> + return dev_err_probe(dev, PTR_ERR(pcie->reset_gpio),
> + "failed to get perst-gpio\n");
> +
> + pcie->power_gpio = devm_gpiod_get_optional(dev, "enable",
> + GPIOD_OUT_LOW);
> + if (IS_ERR(pcie->power_gpio))
> + return dev_err_probe(dev, PTR_ERR(pcie->power_gpio),
> + "failed to get power-gpio\n");
> +
> + return 0;
> +}
> +
> +static struct pci_ops starfive_pcie_ops = {
> + .map_bus = plda_pcie_map_bus,
It looks like this is an ECAM driver with the read/config quirks
for read/write in the method below. Please explain why they are needed.
> + .read = starfive_pcie_config_read,
> + .write = starfive_pcie_config_write,
> +};
> +
> +static int starfive_pcie_clk_rst_init(struct starfive_jh7110_pcie *pcie)
> +{
> + struct device *dev = pcie->plda.dev;
> + int ret;
> +
> + ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to enable clocks\n");
> +
> + ret = reset_control_deassert(pcie->resets);
> + if (ret) {
> + clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
> + dev_err_probe(dev, ret, "failed to deassert resets\n");
> + }
> +
> + return ret;
> +}
> +
> +static void starfive_pcie_clk_rst_deinit(struct starfive_jh7110_pcie *pcie)
> +{
> + reset_control_assert(pcie->resets);
> + clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
> +}
> +
> +static bool starfive_pcie_link_up(struct plda_pcie_rp *plda)
> +{
> + struct starfive_jh7110_pcie *pcie =
> + container_of(plda, struct starfive_jh7110_pcie, plda);
> + int ret;
> + u32 stg_reg_val;
> +
> + ret = regmap_read(pcie->reg_syscon,
> + pcie->stg_pcie_base + STG_SYSCON_LNKSTA_OFFSET,
> + &stg_reg_val);
> + if (ret) {
> + dev_err(pcie->plda.dev, "failed to read link status\n");
> + return false;
> + }
> +
> + return !!(stg_reg_val & DATA_LINK_ACTIVE);
> +}
> +
> +static int starfive_pcie_host_wait_for_link(struct starfive_jh7110_pcie *pcie)
> +{
> + int retries;
> +
> + /* Check if the link is up or not */
> + for (retries = 0; retries < LINK_WAIT_MAX_RETRIES; retries++) {
> + if (starfive_pcie_link_up(&pcie->plda)) {
> + dev_info(pcie->plda.dev, "port link up\n");
> + return 0;
> + }
> + usleep_range(LINK_WAIT_USLEEP_MIN, LINK_WAIT_USLEEP_MAX);
> + }
> +
> + return -ETIMEDOUT;
> +}
> +
> +static int starfive_pcie_enable_phy(struct device *dev,
> + struct starfive_jh7110_pcie *pcie)
> +{
> + int ret;
> +
> + if (!pcie->phy)
> + return 0;
> +
> + ret = phy_init(pcie->phy);
> + if (ret)
> + return dev_err_probe(dev, ret,
> + "failed to initialize pcie phy\n");
> +
> + ret = phy_set_mode(pcie->phy, PHY_MODE_PCIE);
> + if (ret) {
> + dev_err_probe(dev, ret, "failed to set pcie mode\n");
> + goto err_phy_on;
> + }
> +
> + ret = phy_power_on(pcie->phy);
> + if (ret) {
> + dev_err_probe(dev, ret, "failed to power on pcie phy\n");
> + goto err_phy_on;
> + }
> +
> + return 0;
> +
> +err_phy_on:
> + phy_exit(pcie->phy);
> + return ret;
> +}
> +
> +static void starfive_pcie_disable_phy(struct starfive_jh7110_pcie *pcie)
> +{
> + phy_power_off(pcie->phy);
> + phy_exit(pcie->phy);
> +}
> +
> +static void starfive_pcie_host_deinit(struct plda_pcie_rp *plda)
> +{
> + struct starfive_jh7110_pcie *pcie =
> + container_of(plda, struct starfive_jh7110_pcie, plda);
> +
> + starfive_pcie_clk_rst_deinit(pcie);
> + if (pcie->power_gpio)
> + gpiod_set_value_cansleep(pcie->power_gpio, 0);
> + starfive_pcie_disable_phy(pcie);
> +}
> +
> +static int starfive_pcie_host_init(struct plda_pcie_rp *plda)
> +{
> + struct starfive_jh7110_pcie *pcie =
> + container_of(plda, struct starfive_jh7110_pcie, plda);
> + struct device *dev = plda->dev;
> + int ret;
> + int i;
> +
> + ret = starfive_pcie_enable_phy(dev, pcie);
> + if (ret)
> + return ret;
> +
> + regmap_update_bits(pcie->reg_syscon,
> + pcie->stg_pcie_base + STG_SYSCON_RP_NEP_OFFSET,
> + STG_SYSCON_K_RP_NEP, STG_SYSCON_K_RP_NEP);
> +
> + regmap_update_bits(pcie->reg_syscon,
> + pcie->stg_pcie_base + STG_SYSCON_AW_OFFSET,
> + STG_SYSCON_CKREF_SRC_MASK,
> + FIELD_PREP(STG_SYSCON_CKREF_SRC_MASK, 2));
> +
> + regmap_update_bits(pcie->reg_syscon,
> + pcie->stg_pcie_base + STG_SYSCON_AW_OFFSET,
> + STG_SYSCON_CLKREQ, STG_SYSCON_CLKREQ);
> +
> + ret = starfive_pcie_clk_rst_init(pcie);
> + if (ret)
> + return ret;
> +
> + if (pcie->power_gpio)
> + gpiod_set_value_cansleep(pcie->power_gpio, 1);
> +
> + if (pcie->reset_gpio)
> + gpiod_set_value_cansleep(pcie->reset_gpio, 1);
> +
> + /* Disable physical functions except #0 */
> + for (i = 1; i < PCIE_FUNC_NUM; i++) {
> + regmap_update_bits(pcie->reg_syscon,
> + pcie->stg_pcie_base + STG_SYSCON_AR_OFFSET,
> + STG_SYSCON_AXI4_SLVL_AR_MASK,
> + STG_SYSCON_AXI4_SLVL_PHY_AR(i));
> +
> + regmap_update_bits(pcie->reg_syscon,
> + pcie->stg_pcie_base + STG_SYSCON_AW_OFFSET,
> + STG_SYSCON_AXI4_SLVL_AW_MASK,
> + STG_SYSCON_AXI4_SLVL_PHY_AW(i));
> +
> + plda_pcie_disable_func(plda);
> + }
> +
> + regmap_update_bits(pcie->reg_syscon,
> + pcie->stg_pcie_base + STG_SYSCON_AR_OFFSET,
> + STG_SYSCON_AXI4_SLVL_AR_MASK, 0);
> + regmap_update_bits(pcie->reg_syscon,
> + pcie->stg_pcie_base + STG_SYSCON_AW_OFFSET,
> + STG_SYSCON_AXI4_SLVL_AW_MASK, 0);
> +
> + plda_pcie_enable_root_port(plda);
> + plda_pcie_write_rc_bar(plda, 0);
> +
> + /* PCIe PCI Standard Configuration Identification Settings. */
> + plda_pcie_set_standard_class(plda);
> +
> + /*
> + * The LTR message forwarding of PCIe Message Reception was set by core
"LTR message forwarding of PCIe Message Reception".
What is this referring to ?
Thanks,
Lorenzo
> + * as default, but the forward id & addr are also need to be reset.
> + * If we do not disable LTR message forwarding here, or set a legal
> + * forwarding address, the kernel will get stuck after the driver probe.
> + * To workaround, disable the LTR message forwarding support on
> + * PCIe Message Reception.
> + */
> + plda_pcie_disable_ltr(plda);
> +
> + /* Prefetchable memory window 64-bit addressing support */
> + plda_pcie_set_pref_win_64bit(plda);
> +
> + /*
> + * Ensure that PERST has been asserted for at least 100 ms,
> + * the sleep value is T_PVPERL from PCIe CEM spec r2.0 (Table 2-4)
> + */
> + msleep(100);
> + if (pcie->reset_gpio)
> + gpiod_set_value_cansleep(pcie->reset_gpio, 0);
> +
> + /*
> + * With a Downstream Port (<=5GT/s), software must wait a minimum
> + * of 100ms following exit from a conventional reset before
> + * sending a configuration request to the device.
> + */
> + msleep(PCIE_RESET_CONFIG_DEVICE_WAIT_MS);
> +
> + if (starfive_pcie_host_wait_for_link(pcie))
> + dev_info(dev, "port link down\n");
> +
> + return 0;
> +}
> +
> +static const struct plda_pcie_host_ops sf_host_ops = {
> + .host_init = starfive_pcie_host_init,
> + .host_deinit = starfive_pcie_host_deinit,
> +};
> +
> +static const struct plda_event stf_pcie_event = {
> + .intx_event = EVENT_PM_MSI_INT_INTX,
> + .msi_event = EVENT_PM_MSI_INT_MSI
> +};
> +
> +static int starfive_pcie_probe(struct platform_device *pdev)
> +{
> + struct starfive_jh7110_pcie *pcie;
> + struct device *dev = &pdev->dev;
> + struct plda_pcie_rp *plda;
> + int ret;
> +
> + pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
> + if (!pcie)
> + return -ENOMEM;
> +
> + plda = &pcie->plda;
> + plda->dev = dev;
> +
> + ret = starfive_pcie_parse_dt(pcie, dev);
> + if (ret)
> + return ret;
> +
> + plda->host_ops = &sf_host_ops;
> + plda->num_events = PLDA_MAX_EVENT_NUM;
> + /* mask doorbell event */
> + plda->events_bitmap = GENMASK(PLDA_INT_EVENT_NUM - 1, 0)
> + & ~BIT(PLDA_AXI_DOORBELL)
> + & ~BIT(PLDA_PCIE_DOORBELL);
> + plda->events_bitmap <<= PLDA_NUM_DMA_EVENTS;
> + ret = plda_pcie_host_init(&pcie->plda, &starfive_pcie_ops,
> + &stf_pcie_event);
> + if (ret)
> + return ret;
> +
> + pm_runtime_enable(&pdev->dev);
> + pm_runtime_get_sync(&pdev->dev);
> + platform_set_drvdata(pdev, pcie);
> +
> + return 0;
> +}
> +
> +static void starfive_pcie_remove(struct platform_device *pdev)
> +{
> + struct starfive_jh7110_pcie *pcie = platform_get_drvdata(pdev);
> +
> + pm_runtime_put(&pdev->dev);
> + pm_runtime_disable(&pdev->dev);
> + plda_pcie_host_deinit(&pcie->plda);
> + platform_set_drvdata(pdev, NULL);
> +}
> +
> +static int starfive_pcie_suspend_noirq(struct device *dev)
> +{
> + struct starfive_jh7110_pcie *pcie = dev_get_drvdata(dev);
> +
> + clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
> + starfive_pcie_disable_phy(pcie);
> +
> + return 0;
> +}
> +
> +static int starfive_pcie_resume_noirq(struct device *dev)
> +{
> + struct starfive_jh7110_pcie *pcie = dev_get_drvdata(dev);
> + int ret;
> +
> + ret = starfive_pcie_enable_phy(dev, pcie);
> + if (ret)
> + return ret;
> +
> + ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
> + if (ret) {
> + dev_err(dev, "failed to enable clocks\n");
> + starfive_pcie_disable_phy(pcie);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static const struct dev_pm_ops starfive_pcie_pm_ops = {
> + NOIRQ_SYSTEM_SLEEP_PM_OPS(starfive_pcie_suspend_noirq,
> + starfive_pcie_resume_noirq)
> +};
> +
> +static const struct of_device_id starfive_pcie_of_match[] = {
> + { .compatible = "starfive,jh7110-pcie", },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, starfive_pcie_of_match);
> +
> +static struct platform_driver starfive_pcie_driver = {
> + .driver = {
> + .name = "pcie-starfive",
> + .of_match_table = of_match_ptr(starfive_pcie_of_match),
> + .pm = pm_sleep_ptr(&starfive_pcie_pm_ops),
> + },
> + .probe = starfive_pcie_probe,
> + .remove_new = starfive_pcie_remove,
> +};
> +module_platform_driver(starfive_pcie_driver);
> +
> +MODULE_DESCRIPTION("StarFive JH7110 PCIe host driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.17.1
>
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-riscv
