Hi all, This series adds PCIe bandwidth controller (bwctrl) and associated PCIe cooling driver to the thermal core side for limiting PCIe Link Speed due to thermal reasons. PCIe bandwidth controller is a PCI express bus port service driver. A cooling device is created for each port the service driver finds if they support changing speeds. This series only adds support for controlling PCIe Link Speed. Controlling PCIe Link Width might also be useful but AFAIK, there is no mechanism for that until PCIe 6.0 (L0p) so Link Width throttling is not added by this series. bwctrl is built on top of BW notifications revert. It tried to look into using cached link speed values more in code unrelated to what bwctrl needs but every case I looked non-trivial so I left such attempts as further work. v4: - Merge Port's and Endpoint's Supported Link Speeds Vectors into supported_speeds in the struct pci_bus - Reuse pcie_get_speed_cap()'s code for pcie_get_supported_speeds() - Setup supported_speeds with PCI_EXP_LNKCAP2_SLS_2_5GB when no Endpoint exists - Squash revert + add bwctrl patches into one - Change to use threaded IRQ + IRQF_ONESHOT - Enable also LABIE / LABS - Convert Link Speed selection to use bit logic instead of loop - Allocate before requesting IRQ during probe - Use devm_*() - Use u8 for speed_conv array instead of u16 - Removed READ_ONCE() - Improve changelogs, comments, and Kconfig - Name functions slightly more consistently - Use bullet list for RMW protected registers in docs v3: - Correct hfi1 shortlog prefix - Improve error prints in hfi1 - Add L: linux-pci to the MAINTAINERS entry v2: - Adds LNKCTL2 to RMW safe list in Documentation/PCI/pciebus-howto.rst - Renamed cooling devices from PCIe_Port_* to PCIe_Port_Link_Speed_* in order to plan for possibility of adding Link Width cooling devices later on - Moved struct thermal_cooling_device declaration to the correct patch - Small tweaks to Kconfig texts - Series rebased to resolve conflict (in the selftest list) Ilpo Järvinen (8): PCI: Protect Link Control 2 Register with RMW locking drm/radeon: Use RMW accessors for changing LNKCTL2 drm/amdgpu: Use RMW accessors for changing LNKCTL2 RDMA/hfi1: Use RMW accessors for changing LNKCTL2 PCI: Store all PCIe Supported Link Speeds PCI/link: Re-add BW notification portdrv as PCIe BW controller thermal: Add PCIe cooling driver selftests/pcie_bwctrl: Create selftests Documentation/PCI/pciebus-howto.rst | 14 +- MAINTAINERS | 9 + drivers/gpu/drm/amd/amdgpu/cik.c | 41 +-- drivers/gpu/drm/amd/amdgpu/si.c | 41 +-- drivers/gpu/drm/radeon/cik.c | 40 +-- drivers/gpu/drm/radeon/si.c | 40 +-- drivers/infiniband/hw/hfi1/pcie.c | 30 +- drivers/pci/pci.c | 59 ++-- drivers/pci/pcie/Kconfig | 12 + drivers/pci/pcie/Makefile | 1 + drivers/pci/pcie/bwctrl.c | 269 ++++++++++++++++++ drivers/pci/pcie/portdrv.c | 9 +- drivers/pci/pcie/portdrv.h | 10 +- drivers/pci/probe.c | 8 + drivers/pci/remove.c | 3 + drivers/thermal/Kconfig | 10 + drivers/thermal/Makefile | 2 + drivers/thermal/pcie_cooling.c | 107 +++++++ include/linux/pci-bwctrl.h | 33 +++ include/linux/pci.h | 11 + include/uapi/linux/pci_regs.h | 1 + tools/testing/selftests/Makefile | 1 + tools/testing/selftests/pcie_bwctrl/Makefile | 2 + .../pcie_bwctrl/set_pcie_cooling_state.sh | 122 ++++++++ .../selftests/pcie_bwctrl/set_pcie_speed.sh | 67 +++++ 25 files changed, 789 insertions(+), 153 deletions(-) create mode 100644 drivers/pci/pcie/bwctrl.c create mode 100644 drivers/thermal/pcie_cooling.c create mode 100644 include/linux/pci-bwctrl.h create mode 100644 tools/testing/selftests/pcie_bwctrl/Makefile create mode 100755 tools/testing/selftests/pcie_bwctrl/set_pcie_cooling_state.sh create mode 100755 tools/testing/selftests/pcie_bwctrl/set_pcie_speed.sh -- 2.39.2
