Re: [PATCH v2] PCI: dra7xx: Fix reset behaviour

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Pali,

On 22/06/21 23:19, Pali Rohár wrote:
> On Tuesday 22 June 2021 23:08:07 Luca Ceresoli wrote:
>> On 22/06/21 22:52, Pali Rohár wrote:
>>> On Tuesday 22 June 2021 19:27:37 Kishon Vijay Abraham I wrote:
>>>> Hi Luca, Pali,
>>>>
>>>> On 22/06/21 7:01 pm, Luca Ceresoli wrote:
>>>>> Hi,
>>>>>
>>>>> On 22/06/21 14:16, Pali Rohár wrote:
>>>>>> On Tuesday 22 June 2021 12:56:04 Lorenzo Pieralisi wrote:
>>>>>>> [Adding Linus for GPIO discussion, thread:
>>>>>>> https://lore.kernel.org/linux-pci/20210531090540.2663171-1-luca@xxxxxxxxxxxxxxxx]
>>>>>>>
>>>>>>> On Tue, Jun 22, 2021 at 01:06:27PM +0200, Pali Rohár wrote:
>>>>>>>> Hello!
>>>>>>>>
>>>>>>>> On Tuesday 22 June 2021 12:57:22 Luca Ceresoli wrote:
>>>>>>>>> Nothing happened after a few weeks... I understand that knowing the
>>>>>>>>> correct reset timings is relevant, but unfortunately I cannot help much
>>>>>>>>> in finding out the correct values.
>>>>>>>>>
>>>>>>>>> However I'm wondering what should happen to this patch. It *does* fix a
>>>>>>>>> real bug, but potentially with an incorrect or non-optimal usleep range.
>>>>>>>>> Do we really want to ignore a bugfix because we are not sure about how
>>>>>>>>> long this delay should be?
>>>>>>>>
>>>>>>>> As there is no better solution right now, I'm fine with your patch. But
>>>>>>>> patch needs to be approved by Lorenzo, so please wait for his final
>>>>>>>> answer.
>>>>>>>
>>>>>>> I am not a GPIO expert and I have a feeling this is platform specific
>>>>>>> beyond what the PCI specification can actually define architecturally.
>>>>>>
>>>>>> In my opinion timeout is not platform specific as I wrote in email:
>>>>>> https://lore.kernel.org/linux-pci/20210310110535.zh4pnn4vpmvzwl5q@pali/
>>>>>>
>>>>>> My experiments already proved that some PCIe cards needs to be in reset
>>>>>> state for some minimal time otherwise they cannot be enumerated. And it
>>>>>> does not matter to which platform you connect those (endpoint) cards.
>>>>>>
>>>>>> I do not think that timeout itself is platform specific. GPIO controls
>>>>>> PERST# pin and therefore specified sleep value directly drives how long
>>>>>> is card on the other end of PCIe slot in Warm Reset state. PCIe CEM spec
>>>>>> directly says that PERST# signal controls PCIe Warm Reset.
>>>>>>
>>>>>> What is here platform specific thing is that PERST# signal is controlled
>>>>>> by GPIO. But value of signal (high / low) and how long is in signal in
>>>>>> which state for me sounds like not an platform specific thing, but as
>>>>>> PCIe / CEM related.
>>>>>
>>>>> That's exactly my understanding of this matter. At least for the dra7xx
>>>>> controller it works exactly like this, PERSTn# is nothing but a GPIO
>>>>> output from the SoC that drives the PERSTn# input of the external chip
>>>>> without affecting the controller directly.
>>>>>
>>>>
>>>> While the patch itself is correct, this kind-of changes the behavior on
>>>> already upstreamed platforms. Previously the driver expected #PERST to
>>>> be asserted be external means (or default power-up state) and only takes
>>>> care of de-asserting the #PERST line.
>>>>
>>>> There are 2 platforms that will be impacted due to this change
>>>> 1) arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi (has an inverter on
>>>> GPIO line)
>>>> 2) arch/arm/boot/dts/am571x-idk.dts (directly connected to #PERST)
>>>>
>>>> For 1), gpiod_set_value(reset, 0) will assert the PERST line due to the
>>>> inverter (and GPIO_ACTIVE_LOW)
>>>> For 2), gpiod_set_value(reset, 0) will assert the PERST line because we
>>>> have GPIO_ACTIVE_HIGH
>>>
>>> Ou! This is a problem in DT. It needs to be defined in a way that state
>>> is same for every DTS device which uses this driver.
>>
>> Why?
> 
> I'm starting to be confused by triple or more negations (asserting,
> signal inverter, active low)...
> 
> In your patch is GPIO set value to 0 and Kishon wrote that GPIO set
> value to 0 for those two boards assert PERST# line. Asserting PERST#
> line cause endpoint PCIe card to be in reset state. And in pci-dra7xx.c
> driver there is no other code which de-asserts PERST# line.
> 
> So based on all this information I deduced that your patch will cause
> putting PCIe cards into reset state (forever) and therefore they would
> not work.
> 
> Or do I have here some mistake?

Uhm, at time time in the night I'm not sure I can do much more than
adding a few notes on top of the commit message. I hope it helps anyway.

The PCIe PERSTn reset pin is active low and should be asserted, then
deasserted.

The current implementation only drives the pin once in "HIGH" position,
thus presumably it was intended to deassert the pin. This has two problems:

  1) it assumes the pin was asserted by other means before loading the
     driver [Note: Kishon confirmed so far]
  2) it has the wrong polarity, since "HIGH" means "active", and the pin is
     presumably configured as active low coherently with the PCIe
     convention, thus it is driven physically to 0, keeping the device
     under reset unless the pin is configured as active high.
     [Note: the curren 2 DTS files pointed to by Kishon have different
      polarities]

Fix both problems by:

  1) keeping devm_gpiod_get_optional(dev, NULL, GPIOD_OUT_HIGH) as is, but
     assuming the pin is correctly configured as "active low" this now
     becomes a reset assertion
  2) adding gpiod_set_value(reset, 0) after a delay to deassert reset
[Note: this is exactly the current idea, but with the additional need to
fix (=invert) the current polarities in DT]

-- 
Luca




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux