Nishanth Menon <nm@xxxxxx> writes:
> On 15:09-20130524, Nishanth Menon wrote:
>> On 12:28-20130524, Kevin Hilman wrote:
>> > Earlier commits ensured proper muxing of pins related to proper
>> > TWL6030 behavior: see commit 265a2bc8 (ARM: OMAP3: TWL4030: ensure
>> > sys_nirq1 is mux'd and wakeup enabled) and commit 1ef43369 (ARM:
>> > OMAP4: TWL: mux sys_drm_msecure as output for PMIC).
>> >
>> > However these only fixed legacy boot and not DT boot. For DT boot,
>> > the default mux values need to be set properly in DT.
>> >
>> > Cc: Tony Lindgren <tony@xxxxxxxxxxx>
>> > Signed-off-by: Kevin Hilman <khilman@xxxxxxxxxx>
>> > ---
>> > Applies on v3.10-rc2
>> >
>> > arch/arm/boot/dts/omap4-panda-common.dtsi | 8 ++++++++
>> > arch/arm/boot/dts/omap4-sdp.dts | 8 ++++++++
>> > 2 files changed, 16 insertions(+)
>> >
>> > diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
>> > index 03bd60d..a7a9bc0 100644
>> > --- a/arch/arm/boot/dts/omap4-panda-common.dtsi
>> > +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
>> > @@ -59,6 +59,7 @@
>> > &omap4_pmx_core {
>> > pinctrl-names = "default";
>> > pinctrl-0 = <
>> > + &twl6030_pins
>> > &twl6040_pins
>> > &mcpdm_pins
>> > &mcbsp1_pins
>> > @@ -66,6 +67,13 @@
>> > &tpd12s015_pins
>> > >;
>> >
>> > + twl6030_pins: pinmux_twl6030_pins {
>> > + pinctrl-single,pins = <
>> > + 0x15e 0x4118 /* sys_nirq1.sys_nirq1 OMAP_WAKEUP_EN | INPUT_PULLUP | MODE0 */
>> I can understand this - IRQ request comes here.
>> verified on OMAP4460 Panda-ES.
>> # omapconf read 0x4A10019C
>> 4118011B
>>
>> > + 0x14 0x0 /* fref_clk0_out.sys_drm_msecure OUTPUT */
>> I do not understand this.
>> OMAP4460 TRM:
>> Register: CONTROL_WKUP_PAD0_FREF_CLK0_OUT_PAD1_FREF_CLK3_REQ
>> omapconf read 0x4A31E054
>> 010F010F
>>
>> I do not understand this configuration. mux modes for
>> FREF_CLK0_OUT_MUXMODE:
>> 0x0: Select fref_clk0_out
>> 0x1: Select fref_clk1_req
>> 0x2: Reserved
>> 0x3: Select gpio_wk6
>> 0x5: Select sdmmc2_dat7
>> 0x6: Select hw_dbg6
>> 0x7: Select safe_mode
>>
>> Why are we setting mode 0(clk out) here?
>
> I did a bit more research into this:
> MSECURE line needs to be set for us to set anything with TWL6030 RTC.
Yes, the commit referenced in the changelog described that in detail.
> PandaBoard ES(4460) = this is on OMAP PIN AD4
> PandaBoard (4430) = this is on OMAP PIN AD2
>
> translating this back,
> PandaBoard ES OMAp4460 pin AD4:
> FREF_CLK3_OUT/FREF_CLK2_REQ/SYS_SECURE_INDICATOR/GPIO_WK31/C2C_WAKEREQOUT/SDMMC2_DAT5/ATTILA_HW_DBG8/SAFE_MODE
> This is at register 0x4A31E054(higher 16 bits) - however since we are GP device,
> SYS_SECURE_INDICATOR(mode 2) is reserved.
> PandaBoard OMAP4430 pin AD2:
> FREF_CLK0_OUT/FREF_CLK1_REQ/SYS_DRM_MSECURE/GPIO_WK6/SDMMC2_DAT7/ATTILA_HW_DBG6/SAFE_MOD
> This is at register 0x4A31E054(lower 16 bits) - however since we are GP device,
> SYS_DRM_MSECURE(mode 2) is reserved.
>
> To use RTC, we will have to use GPIO.
> on pandaboard ES, we need GPIO31 and PandaBoard, 6.
>
> Further the pinctrl offsets will vary as well between the same.
>
> IMHO, we need GPIO support and pinmux appropritate to the same to allow
> RTC to work.
I don't follow at all what you're trying to say. The current settings
are working fine and have been tested on both 4430/Panda and 4460/Panda-ES.
The goal of this patch is to make default mux settings for twl6030 for
DT boot match current legacy boot in mainline.
The commits referenced in the changelog setup some default muxing for
twl6030 (see changelogs referenced and mux calls in
twl-common.c:omap4_pmic_init())
Without those mux settings, RTC wakeup on legacy boot does not work
(tested on 4430/panda, 4460/Panda with recent u-boot v2013.04 where most
of the old mux setup is gone.) With those settings, RTC wakeup works.
Yes, the TRM has some mode bits marked as reserved, but that doesn't
mean they don't work. It just means the documentation is squirreled
away in the secure TRM addendum.
Kevin
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
