On 15:09-20130524, Nishanth Menon wrote:
> On 12:28-20130524, Kevin Hilman wrote:
> > Earlier commits ensured proper muxing of pins related to proper
> > TWL6030 behavior: see commit 265a2bc8 (ARM: OMAP3: TWL4030: ensure
> > sys_nirq1 is mux'd and wakeup enabled) and commit 1ef43369 (ARM:
> > OMAP4: TWL: mux sys_drm_msecure as output for PMIC).
> >
> > However these only fixed legacy boot and not DT boot. For DT boot,
> > the default mux values need to be set properly in DT.
> >
> > Cc: Tony Lindgren <tony@xxxxxxxxxxx>
> > Signed-off-by: Kevin Hilman <khilman@xxxxxxxxxx>
> > ---
> > Applies on v3.10-rc2
> >
> > arch/arm/boot/dts/omap4-panda-common.dtsi | 8 ++++++++
> > arch/arm/boot/dts/omap4-sdp.dts | 8 ++++++++
> > 2 files changed, 16 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
> > index 03bd60d..a7a9bc0 100644
> > --- a/arch/arm/boot/dts/omap4-panda-common.dtsi
> > +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
> > @@ -59,6 +59,7 @@
> > &omap4_pmx_core {
> > pinctrl-names = "default";
> > pinctrl-0 = <
> > + &twl6030_pins
> > &twl6040_pins
> > &mcpdm_pins
> > &mcbsp1_pins
> > @@ -66,6 +67,13 @@
> > &tpd12s015_pins
> > >;
> >
> > + twl6030_pins: pinmux_twl6030_pins {
> > + pinctrl-single,pins = <
> > + 0x15e 0x4118 /* sys_nirq1.sys_nirq1 OMAP_WAKEUP_EN | INPUT_PULLUP | MODE0 */
> I can understand this - IRQ request comes here.
> verified on OMAP4460 Panda-ES.
> # omapconf read 0x4A10019C
> 4118011B
>
> > + 0x14 0x0 /* fref_clk0_out.sys_drm_msecure OUTPUT */
> I do not understand this.
> OMAP4460 TRM:
> Register: CONTROL_WKUP_PAD0_FREF_CLK0_OUT_PAD1_FREF_CLK3_REQ
> omapconf read 0x4A31E054
> 010F010F
>
> I do not understand this configuration. mux modes for
> FREF_CLK0_OUT_MUXMODE:
> 0x0: Select fref_clk0_out
> 0x1: Select fref_clk1_req
> 0x2: Reserved
> 0x3: Select gpio_wk6
> 0x5: Select sdmmc2_dat7
> 0x6: Select hw_dbg6
> 0x7: Select safe_mode
>
> Why are we setting mode 0(clk out) here?
I did a bit more research into this:
MSECURE line needs to be set for us to set anything with TWL6030 RTC.
PandaBoard ES(4460) = this is on OMAP PIN AD4
PandaBoard (4430) = this is on OMAP PIN AD2
translating this back,
PandaBoard ES OMAp4460 pin AD4:
FREF_CLK3_OUT/FREF_CLK2_REQ/SYS_SECURE_INDICATOR/GPIO_WK31/C2C_WAKEREQOUT/SDMMC2_DAT5/ATTILA_HW_DBG8/SAFE_MODE
This is at register 0x4A31E054(higher 16 bits) - however since we are GP device,
SYS_SECURE_INDICATOR(mode 2) is reserved.
PandaBoard OMAP4430 pin AD2:
FREF_CLK0_OUT/FREF_CLK1_REQ/SYS_DRM_MSECURE/GPIO_WK6/SDMMC2_DAT7/ATTILA_HW_DBG6/SAFE_MOD
This is at register 0x4A31E054(lower 16 bits) - however since we are GP device,
SYS_DRM_MSECURE(mode 2) is reserved.
To use RTC, we will have to use GPIO.
on pandaboard ES, we need GPIO31 and PandaBoard, 6.
Further the pinctrl offsets will vary as well between the same.
IMHO, we need GPIO support and pinmux appropritate to the same to allow
RTC to work.
> > + >;
> > + };
> > +
> > twl6040_pins: pinmux_twl6040_pins {
> > pinctrl-single,pins = <
> > 0xe0 0x3 /* hdq_sio.gpio_127 OUTPUT | MODE3 */
> > diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
> > index a35d9cd..5ad0c10 100644
> > --- a/arch/arm/boot/dts/omap4-sdp.dts
> > +++ b/arch/arm/boot/dts/omap4-sdp.dts
> > @@ -145,6 +145,7 @@
> > &omap4_pmx_core {
> > pinctrl-names = "default";
> > pinctrl-0 = <
> > + &twl6030_pins
> > &twl6040_pins
> > &mcpdm_pins
> > &dmic_pins
> > @@ -179,6 +180,13 @@
> > >;
> > };
> >
> > + twl6030_pins: pinmux_twl6030_pins {
> > + pinctrl-single,pins = <
> > + 0x15e 0x4118 /* sys_nirq1.sys_nirq1 OMAP_WAKEUP_EN | INPUT_PULLUP | MODE0 */
> > + 0x14 0x0 /* fref_clk0_out.sys_drm_msecure OUTPUT */
> > + >;
> > + };
> > +
> > twl6040_pins: pinmux_twl6040_pins {
> > pinctrl-single,pins = <
> > 0xe0 0x3 /* hdq_sio.gpio_127 OUTPUT | MODE3 */
> > --
> > 1.8.2
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> > the body of a message to majordomo@xxxxxxxxxxxxxxx
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
>
> --
> Regards,
> Nishanth Menon
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Regards,
Nishanth Menon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
