Hello.
On 15-09-2011 18:19, Kishon Vijay Abraham I wrote:
Setting OTG_INTERFSEL to UTMI interferes with charger detection resulting
in incorrect detection of charger type. Hence OTG_INTERFSEL is configured to
ULPI initially and changed to UTMI only after receiving USB_EVENT_ID or
USB_EVENT_VBUS notification.
Signed-off-by: Kishon Vijay Abraham I<kishon@xxxxxx>
Signed-off-by: Balaji T K<balajitk@xxxxxx>
AFAIK, full name is needed here.
[sandesh.gowda@xxxxxx: The interface selection has to be done before the PHY
is activated and is not allowed to change when the PHY clock is already
running]
No signoff from him?
---
drivers/usb/musb/omap2430.c | 50 +++++++++++++++++++++++++++++++++++-------
1 files changed, 41 insertions(+), 9 deletions(-)
diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
index fc9377c..724450b 100644
--- a/drivers/usb/musb/omap2430.c
+++ b/drivers/usb/musb/omap2430.c
@@ -228,6 +228,7 @@ static inline void omap2430_low_level_init(struct musb *musb)
static int musb_otg_notifications(struct notifier_block *nb,
unsigned long event, void *unused)
{
+ u32 val;
struct musb *musb = container_of(nb, struct musb, nb);
struct device *dev = musb->controller;
struct musb_hdrc_platform_data *pdata = dev->platform_data;
@@ -240,11 +241,32 @@ static int musb_otg_notifications(struct notifier_block *nb,
if (is_otg_enabled(musb)) {
if (musb->gadget_driver) {
pm_runtime_get_sync(musb->controller);
+
+ val = musb_readl(musb->mregs, OTG_INTERFSEL);
+ if (data->interface_type ==
+ MUSB_INTERFACE_UTMI) {
+ val&= ~ULPI_12PIN;
+ val |= UTMI_8BIT;
+ } else {
+ val |= ULPI_12PIN;
+ }
+ musb_writel(musb->mregs, OTG_INTERFSEL, val);
+
usb_phy_init(musb->xceiv);
omap2430_musb_set_vbus(musb, 1);
}
} else {
pm_runtime_get_sync(musb->controller);
+
+ val = musb_readl(musb->mregs, OTG_INTERFSEL);
+ if (data->interface_type == MUSB_INTERFACE_UTMI) {
+ val&= ~ULPI_12PIN;
+ val |= UTMI_8BIT;
+ } else {
+ val |= ULPI_12PIN;
+ }
+ musb_writel(musb->mregs, OTG_INTERFSEL, val);
+
usb_phy_init(musb->xceiv);
omap2430_musb_set_vbus(musb, 1);
}
@@ -255,6 +277,16 @@ static int musb_otg_notifications(struct notifier_block *nb,
if (musb->gadget_driver)
pm_runtime_get_sync(musb->controller);
+
+ val = musb_readl(musb->mregs, OTG_INTERFSEL);
+ if (data->interface_type == MUSB_INTERFACE_UTMI) {
+ val&= ~ULPI_12PIN;
+ val |= UTMI_8BIT;
+ } else {
+ val |= ULPI_12PIN;
+ }
+ musb_writel(musb->mregs, OTG_INTERFSEL, val);
+
usb_phy_init(musb->xceiv);
break;
Why repeat the same sequence 3 times. Couldn't you factor it out into a
subroutine?
@@ -272,6 +304,11 @@ static int musb_otg_notifications(struct notifier_block *nb,
otg_set_vbus(musb->xceiv->otg, 0);
}
usb_phy_shutdown(musb->xceiv);
+
+ val = musb_readl(musb->mregs, OTG_INTERFSEL);
+ val |= ULPI_12PIN;
+ musb_writel(musb->mregs, OTG_INTERFSEL, val);
+
break;
default:
dev_dbg(musb->controller, "ID float\n");
@@ -304,16 +341,11 @@ static int omap2430_musb_init(struct musb *musb)
goto err1;
}
+ /* Set OTG_INTERFSEL to ULPI for correct charger detection.
+ * This should be later set to UTMI.
+ */
l = musb_readl(musb->mregs, OTG_INTERFSEL);
-
- if (data->interface_type == MUSB_INTERFACE_UTMI) {
- /* OMAP4 uses Internal PHY GS70 which uses UTMI interface */
- l&= ~ULPI_12PIN; /* Disable ULPI */
- l |= UTMI_8BIT; /* Enable UTMI */
- } else {
- l |= ULPI_12PIN;
- }
-
+ l |= ULPI_12PIN;
musb_writel(musb->mregs, OTG_INTERFSEL, l);
This also seems to be the same code repeated twice...
WBR, Sergei
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
