Most revisions of the OMAP4 Blaze/SDP platform do not have the EHCI signals routed by default. The pads are routed for the alternate HSI functionality instead, and explicit board modifications are needed to route the signals to the USB PHY on the board. Also, turning on the PHY connected to the EHCI port causes a board reboot during bootup due to an unintended short on the rails - this affects many initial revisions of the board, and needs a minor board mod to fix (or as a workaround, one should not attempt to power on the USB PHY). Given that these boards need explicit board mods to even get EHCI working (separate from the accidental short above), we should not attempt to enable EHCI by default. So drop the EHCI support from the board files for the Blaze/SDP platforms. Signed-off-by: Anand Gadiyar <gadiyar@xxxxxx> Cc: Keshava Munegowda <keshava_mgowda@xxxxxx> Cc: Tony Lindgren <tony@xxxxxxxxxxx> --- arch/arm/mach-omap2/board-4430sdp.c | 20 -------------------- 1 file changed, 20 deletions(-) Index: linux-omap-usb/arch/arm/mach-omap2/board-4430sdp.c =================================================================== --- linux-omap-usb.orig/arch/arm/mach-omap2/board-4430sdp.c +++ linux-omap-usb/arch/arm/mach-omap2/board-4430sdp.c @@ -44,7 +44,6 @@ #define ETH_KS8851_IRQ 34 #define ETH_KS8851_POWER_ON 48 #define ETH_KS8851_QUART 138 -#define OMAP4SDP_MDM_PWR_EN_GPIO 157 #define OMAP4_SFH7741_SENSOR_OUTPUT_GPIO 184 #define OMAP4_SFH7741_ENABLE_GPIO 188 @@ -251,16 +250,6 @@ static void __init omap_4430sdp_init_irq gic_init_irq(); } -static const struct ehci_hcd_omap_platform_data ehci_pdata __initconst = { - .port_mode[0] = EHCI_HCD_OMAP_MODE_PHY, - .port_mode[1] = EHCI_HCD_OMAP_MODE_UNKNOWN, - .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN, - .phy_reset = false, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL, -}; - static struct omap_musb_board_data musb_board_data = { .interface_type = MUSB_INTERFACE_UTMI, .mode = MUSB_OTG, @@ -576,14 +564,6 @@ static void __init omap_4430sdp_init(voi omap_serial_init(); omap4_twl6030_hsmmc_init(mmc); - /* Power on the ULPI PHY */ - status = gpio_request(OMAP4SDP_MDM_PWR_EN_GPIO, "USBB1 PHY VMDM_3V3"); - if (status) - pr_err("%s: Could not get USBB1 PHY GPIO\n", __func__); - else - gpio_direction_output(OMAP4SDP_MDM_PWR_EN_GPIO, 1); - - usb_ehci_init(&ehci_pdata); usb_musb_init(&musb_board_data); status = omap_ethernet_init(); -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html