Use the mux framework to initialise the serial pads.
Signed-off-by: sricharan <r.sricharan@xxxxxx>
---
arch/arm/mach-omap2/board-omap4panda.c | 72 +++++++++++++++++++++++++++++++-
1 files changed, 71 insertions(+), 1 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index b43e3ff..9688ea9 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -370,13 +370,83 @@ static int __init omap4_panda_i2c_init(void)
omap_register_i2c_bus(4, 400, NULL, 0);
return 0;
}
-
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
+
+static struct omap_device_pad serial2_pads[] __initdata = {
+ { .name = "uart2_cts.uart2_cts",
+ .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+ .flags = OMAP_DEVICE_PAD_REMUX_IDLE,
+ .idle = OMAP_MUX_MODE7,
+ },
+ { .name = "uart2_rts.uart2_rts",
+ .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+ },
+ { .name = "uart2_rx.uart2_rx",
+ .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+ },
+ { .name = "uart2_tx.uart2_tx",
+ .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+ },
+};
+
+static struct omap_device_pad serial3_pads[] __initdata = {
+ { .name = "uart3_cts_rctx.uart3_cts_rctx",
+ .enable = OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0,
+ },
+ { .name = "uart3_rts_sd.uart3_rts_sd",
+ .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+ },
+ { .name = "uart3_rx_irrx.uart3_rx_irrx",
+ .enable = OMAP_PIN_INPUT | OMAP_MUX_MODE0,
+ },
+ { .name = "uart3_tx_irtx.uart3_tx_irtx",
+ .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+ },
+};
+
+static struct omap_device_pad serial4_pads[] __initdata = {
+ { .name = "uart4_rx.uart4_rx",
+ .enable = OMAP_PIN_INPUT | OMAP_MUX_MODE0,
+ },
+ { .name = "uart4_tx.uart4_tx",
+ .enable = OMAP_PIN_OUTPUT | OMAP_MUX_MODE0,
+ },
+};
+
+static struct omap_board_data serial2_data = {
+ .id = 1,
+ .pads = serial2_pads,
+ .pads_cnt = ARRAY_SIZE(serial2_pads),
+};
+
+static struct omap_board_data serial3_data = {
+ .id = 2,
+ .pads = serial3_pads,
+ .pads_cnt = ARRAY_SIZE(serial3_pads),
+};
+
+static struct omap_board_data serial4_data = {
+ .id = 3,
+ .pads = serial4_pads,
+ .pads_cnt = ARRAY_SIZE(serial4_pads),
+};
+
+static inline void board_serial_init(void)
+{
+ omap_serial_init_port(&serial2_data);
+ omap_serial_init_port(&serial3_data);
+ omap_serial_init_port(&serial4_data);
+}
#else
#define board_mux NULL
+
+static inline void board_serial_init(void)
+{
+ omap_serial_init();
+}
#endif
static void __init omap4_panda_init(void)
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
