From: Thara Gopinath <thara@xxxxxx> The smartreflex bit on twl4030 needs to be enabled by default irrespective of whether smartreflex module is enabled on the OMAP side or not. This is because without this bit enabled the voltage scaling through vp forceupdate does not function properly on OMAP3. There are two APIs being added 'omap3_twl_enable_sr' to set SR bit and other API 'omap3_twl_disable_sr' to disable SR bit for platforms where voltage is not scaled using vpforceupdate or vc_bypass Method. This patch is based on LO PM Branch and Smartreflex has been tested on OMAP3430 SDP, OMAP3630 SDP and boot tested on OMAP2430 SDP. Signed-off-by: Shweta Gulati <shweta.gulati@xxxxxx> Signed-off-by: Thara Gopinath <thara@xxxxxx> --- arch/arm/mach-omap2/omap_twl.c | 46 ++++++++++++++++++++++++++++++++++++++++ arch/arm/mach-omap2/pm.h | 2 + 2 files changed, 48 insertions(+), 0 deletions(-) diff --git a/arch/arm/mach-omap2/omap_twl.c b/arch/arm/mach-omap2/omap_twl.c index 00e1d2b..5b3ca56 100644 --- a/arch/arm/mach-omap2/omap_twl.c +++ b/arch/arm/mach-omap2/omap_twl.c @@ -60,7 +60,9 @@ static bool is_offset_valid; static u8 smps_offset; +#define TWL4030_DCDC_GLOBAL_CFG 0x06 #define REG_SMPS_OFFSET 0xE0 +#define SMARTREFLEX_ENABLE BIT(3) static unsigned long twl4030_vsel_to_uv(const u8 vsel) { @@ -269,6 +271,15 @@ int __init omap3_twl_init(void) omap3_core_volt_info.vp_vddmax = OMAP3630_VP2_VLIMITTO_VDDMAX; } + /* + * The smartreflex bit on twl4030 needs to be enabled by + * default irrespective of whether smartreflex module is + * enabled on the OMAP side or not. This is because without + * this bit enabled the voltage scaling through + * vp forceupdate does not function properly on OMAP3. + */ + omap3_twl_enable_sr(); + voltdm = omap_voltage_domain_lookup("mpu"); omap_voltage_register_pmic(voltdm, &omap3_mpu_volt_info); @@ -277,3 +288,38 @@ int __init omap3_twl_init(void) return 0; } + +/* + * The smartreflex bit on twl4030 is enabled in twl_init + * but there are platforms which use OMAP3 and T2 but use + * Synchronized Scaling Hardware Strategy (ENABLE_VMODE=1) and + * Direct Strategy Software Scaling Mode (ENABLE_VMODE=0). + * for setting the voltages of T2, in those scenarios this bit + * is to be cleared. + */ +void omap3_twl_disable_sr() +{ + u8 temp; + + twl_i2c_read_u8(TWL4030_MODULE_PM_RECEIVER, &temp, + TWL4030_DCDC_GLOBAL_CFG); + temp &= ~SMARTREFLEX_ENABLE; + twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, temp, + TWL4030_DCDC_GLOBAL_CFG); +} + +/* + * To enable Smartreflex bit on TWl 4030 to make sure + * voltage scaling through Vp forceupdate works. + */ + +void omap3_twl_enable_sr() +{ + u8 temp; + + twl_i2c_read_u8(TWL4030_MODULE_PM_RECEIVER, &temp, + TWL4030_DCDC_GLOBAL_CFG); + temp |= SMARTREFLEX_ENABLE; + twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, temp, + TWL4030_DCDC_GLOBAL_CFG); +} diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h index 704766b..8500356 100644 --- a/arch/arm/mach-omap2/pm.h +++ b/arch/arm/mach-omap2/pm.h @@ -127,6 +127,8 @@ static inline void omap_enable_smartreflex_on_init(void) {} #ifdef CONFIG_TWL4030_CORE extern int omap3_twl_init(void); extern int omap4_twl_init(void); +extern void omap3_twl_disable_sr(void); +extern void omap3_twl_enable_sr(void); #else static inline int omap3_twl_init(void) { -- 1.7.0.4 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html