First the disclaimers:
The board is new board that has had hardware mmc/sdio problems before.
It is based closely on beagle but uses a different package which has
some package specific issues. We think we have found them all but who
knows.
My kernel is a few months old 2.6.29.
Ok, given the above issues, it looks to me like I am getting
interrupted every time CIRQ is enabled. Nor sure if the libertas
driver is not disabling as it should or what. So I end up in this
death spiral:
irq handler is called and status indicates CIRQ is pending
mmc_signal_sdio_irq is called which calls omap_hsmmc_enable_sdio_irq
with via mmc_host_ops, en is zero so CIRQ gets disabled
mmc_signal_sdio_irq then wakes up sdio_irq_thread which does its thing
then before going to sleep calls omap_hsmmc_enable_irq with en set to
1 so CIRC gets turned back on
with CIRC enabled the irq handler gets called and we are back where we started.
Looks like either the libertas driver is not disabling the irq or the
CIRQ irq is somehow getting stuck or I have a hw problem.
One thing I did try was to have the sdio_irq_thread basically ignore
the MMC_CAP_SDIO_IRQ flag except for calling
host->ops->enable_sdio_irq(host, 1) and I changed mmc_signal_sdio_irq
to not reschedule sdio_irq_thread. In shows that the mere act of
enabling CIRQ does not break anything. In this mode I get one CIRQ
irq for each time around the sdio_irq_thread loop.
I guess I should try checking the CIRQ bit in the status register
after calling the libertas handler which should clear the irq?
John
On Fri, Oct 16, 2009 at 10:06 AM, Dirk Behme <dirk.behme@xxxxxxxxxxxxxx> wrote:
> John Rigby wrote:
>>
>> Dirk,
>>
>> Thanks for the update. After looking more closely at your patch I
>> found that the only thing my attempt was missing was the IBG setting.
>> I added that to mine with the result that the system hangs on loading
>> the libertas modules.
>
> On which board are you working? libertas does mean you are working on wifi
> connected via SDIO?
>
>> The last thing i see is the firmware request
>> message.
>
> Ok, you see a hang. Below we have a timeout.
>
> I would vote for some interrupt issues. For timeouts I would vote for
> missing interrupts, while system hang might be infinite interrupts
> (something like this was reported in [1]).
>
> Could you add some debug code in omap_hsmmc_enable_sdio_irq() to trace if
> enable/disable is called in the correct order? And in omap_hsmmc_irq() in if
> (status & CIRQ) { to check if and how often it is called?
>
> Best regards
>
> Dirk
>
> [1] http://groups.google.com/group/beagleboard/msg/5cdfe2a319531937
>
>> On Fri, Oct 16, 2009 at 9:02 AM, Dirk Behme <dirk.behme@xxxxxxxxxxxxxx>
>> wrote:
>>>
>>> John,
>>>
>>> John Rigby wrote:
>>>>
>>>> Dirk,
>>>>
>>>> Many thanks, after sending the request yesterday I made my own attempt
>>>> which failed miserably. My patch looks like a subset of yours so that
>>>> is to be expected. I'll try yours out today and report back my
>>>> experience.
>>>
>>> I got already some (private) feedback (thanks!):
>>>
>>> - Accessing host->mmc->card in omap_hsmmc_set_ios() results in a null
>>> pointer :( Seems that mmc->card isn't set yet while calling
>>> omap_hsmmc_set_ios().
>>>
>>> As workaround, for testing only, I hard coded setting IBG with something
>>> like
>>>
>>> case MMC_BUS_WIDTH_4:
>>> OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
>>> - OMAP_HSMMC_WRITE(host->base, HCTL,
>>> - OMAP_HSMMC_READ(host->base, HCTL) | FOUR_BIT);
>>> + OMAP_HSMMC_WRITE(host->base, HCTL,
>>> + OMAP_HSMMC_READ(host->base,
>>> HCTL) |
>>> IBG | FOUR_BIT);
>>> break;
>>>
>>> If you test this, be careful that this doesn't hurt any other 4 bit cards
>>> except the SDIO you want to test.
>>>
>>> Later, we have to find a way how to detect that we are in SDIO mode. We
>>> want
>>> to set IBG only if in SDIO and 4 bit mode.
>>>
>>> - After this, I got the report that null pointer crash is gone. But SDIO
>>> doesn't seem to work any more:
>>>
>>> libertas_sdio: Libertas SDIO driver
>>> libertas_sdio: Copyright Pierre Ossman
>>> libertas_sdio mmc1:0001:1: firmware: requesting sd8686_helper.bin
>>> libertas_sdio mmc1:0001:1: firmware: requesting sd8686.bin
>>> libertas: command 0x0003 timed out
>>> libertas: requeueing command 0x0003 due to timeout (#1)
>>> libertas: command 0x0003 timed out
>>> libertas: requeueing command 0x0003 due to timeout (#2)
>>> libertas: command 0x0003 timed out
>>> libertas: requeueing command 0x0003 due to timeout (#3)
>>> libertas: command 0x0003 timed out
>>> libertas: Excessive timeouts submitting command 0x0003
>>> libertas: PREP_CMD: command 0x0003 failed: -110
>>> libertas_sdio: probe of mmc1:0001:1 failed with error -110
>>>
>>> I now start to think about it ;)
>>>
>>> Again, any help would be appreciated!
>>>
>>> Best regards
>>>
>>> Dirk
>>>
>>>> On Fri, Oct 16, 2009 at 1:16 AM, Dirk Behme <dirk.behme@xxxxxxxxxxxxxx>
>>>> wrote:
>>>>>
>>>>> John Rigby wrote:
>>>>>>
>>>>>> I have seen several discussions about lack of sdio irq support in the
>>>>>> hsmmc driver but no patches. Has anyone on this list implemented this
>>>>>> and/or can anyone point me to patches?
>>>>>
>>>>> What a coincidence ;)
>>>>>
>>>>> I'm currently working on this. See attachment what I currently have. It
>>>>> is
>>>>> compile tested only against recent omap linux head. I don't have a
>>>>> board
>>>>> using SDIO at the moment, so no real testing possible :(
>>>>>
>>>>> Some background, maybe it helps people to step in:
>>>>>
>>>>> Gumstix OMAP3 based Overo air board connects Marvell 88W8686 wifi by
>>>>> MMC
>>>>> port 2 in 4 bit configuration [1]. The wifi performance is quite bad
>>>>> (~100kB/s). There is some rumor that this might be SDIO irq related
>>>>> [2].
>>>>> There was an attempt to fix this [3] already, but this doesn't work
>>>>> [4].
>>>>> Having this, I started to look into it.
>>>>>
>>>>> I used [3], the TI Davinci driver [5] (supporting SDIO irq), the SDIO
>>>>> Simplified Specification [6] and the OMAP35x TRM [7] as starting
>>>>> points.
>>>>>
>>>>> Unfortunately, the Davinci MMC registers and irqs are different
>>>>> (Davinci
>>>>> has
>>>>> a dedicated SDIO irq). But combining [3] and [5] helps to get an idea
>>>>> what
>>>>> has to be done.
>>>>>
>>>>> I think the main issues of [3] were that it doesn't enable IBG for 4
>>>>> bit
>>>>> mode ([6] chapter 8.1.2) and that mmc_omap_irq() doesn't reset the irq
>>>>> bits.
>>>>>
>>>>> Topics I still open:
>>>>>
>>>>> - Is it always necessary to deal with IE _and_ ISE register? I'm not
>>>>> totally
>>>>> clear what the difference between these two registers are ;) And in
>>>>> which
>>>>> order they have to be set.
>>>>>
>>>>> - Davinci driver [5] in line 1115 checks for data line to call
>>>>> mmc_signal_sdio_irq() for irq enable.
>>>>>
>>>>> - Davinci driver deals with SDIO in xfer_done() (line 873)
>>>>>
>>>>> - Davinci driver sets block size to 64 if SDIO in line 701
>>>>>
>>>>> It would be quite nice if anybody likes to comment on attachment and
>>>>> help
>>>>> testing.
>>>>>
>>>>> Many thanks and best regards
>>>>>
>>>>> Dirk
>>>>>
>>>>> [1] http://gumstix.net/wiki/index.php?title=Overo_Wifi
>>>>>
>>>>> [2] http://groups.google.com/group/beagleboard/msg/14e822778c5eeb56
>>>>>
>>>>> [3] http://groups.google.com/group/beagleboard/msg/d0eb69f4c20673be
>>>>>
>>>>> [4] http://groups.google.com/group/beagleboard/msg/5cdfe2a319531937
>>>>>
>>>>> [5]
>>>>>
>>>>>
>>>>> http://arago-project.org/git/projects/?p=linux-davinci.git;a=blob;f=drivers/mmc/host/davinci_mmc.c;h=1bf0587250614c6d8abfe02028b96e0e47148ac8;hb=HEAD
>>>>>
>>>>> [6] http://www.sdcard.org/developers/tech/sdio/sd_bluetooth_spec/
>>>>>
>>>>> [7] http://focus.ti.com/lit/ug/spruf98c/spruf98c.pdf
>>>>>
>>>>>
>>>>> Subject: [PATCH][RFC] OMAP HSMMC: Add SDIO interrupt support
>>>>> Form: Dirk Behme <dirk.behme@xxxxxxxxxxxxxx>
>>>>>
>>>>> At the moment, OMAP HSMMC driver supports only SDIO polling, resulting
>>>>> in
>>>>> poor
>>>>> performance. Add support for SDIO interrupt handling.
>>>>>
>>>>> Signed-off-by: Dirk Behme <dirk.behme@xxxxxxxxxxxxxx>
>>>>> ---
>>>>>
>>>>> Patch against recent omap-linux head "Linux omap got rebuilt from
>>>>> scratch"
>>>>> 274c94b29ee7c53609a756acca974e4742c59559
>>>>>
>>>>> Compile tested only. Please comment and help testing.
>>>>>
>>>>> drivers/mmc/host/omap_hsmmc.c | 48
>>>>> +++++++++++++++++++++++++++++++++++++-----
>>>>> 1 file changed, 43 insertions(+), 5 deletions(-)
>>>>>
>>>>> Index: linux-beagle/drivers/mmc/host/omap_hsmmc.c
>>>>> ===================================================================
>>>>> --- linux-beagle.orig/drivers/mmc/host/omap_hsmmc.c
>>>>> +++ linux-beagle/drivers/mmc/host/omap_hsmmc.c
>>>>> @@ -27,6 +27,7 @@
>>>>> #include <linux/timer.h>
>>>>> #include <linux/clk.h>
>>>>> #include <linux/mmc/host.h>
>>>>> +#include <linux/mmc/card.h>
>>>>> #include <linux/mmc/core.h>
>>>>> #include <linux/io.h>
>>>>> #include <linux/semaphore.h>
>>>>> @@ -65,6 +66,7 @@
>>>>> #define SDVSDET 0x00000400
>>>>> #define AUTOIDLE 0x1
>>>>> #define SDBP (1 << 8)
>>>>> +#define IBG (1 << 19)
>>>>> #define DTO 0xe
>>>>> #define ICE 0x1
>>>>> #define ICS 0x2
>>>>> @@ -76,6 +78,7 @@
>>>>> #define INT_EN_MASK 0x307F0033
>>>>> #define BWR_ENABLE (1 << 4)
>>>>> #define BRR_ENABLE (1 << 5)
>>>>> +#define CIRQ_ENABLE (1 << 8)
>>>>> #define INIT_STREAM (1 << 1)
>>>>> #define DP_SELECT (1 << 21)
>>>>> #define DDIR (1 << 4)
>>>>> @@ -87,6 +90,7 @@
>>>>> #define CC 0x1
>>>>> #define TC 0x02
>>>>> #define OD 0x1
>>>>> +#define CIRQ (1 << 8)
>>>>> #define ERR (1 << 15)
>>>>> #define CMD_TIMEOUT (1 << 16)
>>>>> #define DATA_TIMEOUT (1 << 20)
>>>>> @@ -653,6 +657,15 @@ static irqreturn_t omap_hsmmc_irq(int ir
>>>>> status = OMAP_HSMMC_READ(host->base, STAT);
>>>>> dev_dbg(mmc_dev(host->mmc), "IRQ Status is %x\n", status);
>>>>>
>>>>> + if (status & CIRQ) {
>>>>> + dev_dbg(mmc_dev(host->mmc), "SDIO interrupt");
>>>>> + OMAP_HSMMC_WRITE(host->base, IE,
>>>>> OMAP_HSMMC_READ(host->base,
>>>>> IE)
>>>>> + & ~(CIRQ_ENABLE));
>>>>> + mmc_signal_sdio_irq(host->mmc);
>>>>> + spin_unlock(&host->irq_lock);
>>>>> + return IRQ_HANDLED;
>>>>> + }
>>>>> +
>>>>> if (status & ERR) {
>>>>> #ifdef CONFIG_MMC_DEBUG
>>>>> omap_hsmmc_report_irq(host, status);
>>>>> @@ -1165,8 +1178,15 @@ static void omap_hsmmc_set_ios(struct mm
>>>>> break;
>>>>> case MMC_BUS_WIDTH_4:
>>>>> OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
>>>>> - OMAP_HSMMC_WRITE(host->base, HCTL,
>>>>> - OMAP_HSMMC_READ(host->base, HCTL) | FOUR_BIT);
>>>>> + if (mmc_card_sdio(host->mmc->card)) {
>>>>> + OMAP_HSMMC_WRITE(host->base, HCTL,
>>>>> + OMAP_HSMMC_READ(host->base,
>>>>> HCTL)
>>>>> + | IBG | FOUR_BIT);
>>>>> + } else {
>>>>> + OMAP_HSMMC_WRITE(host->base, HCTL,
>>>>> + OMAP_HSMMC_READ(host->base,
>>>>> HCTL)
>>>>> + | FOUR_BIT);
>>>>> + }
>>>>> break;
>>>>> case MMC_BUS_WIDTH_1:
>>>>> OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
>>>>> @@ -1512,6 +1532,24 @@ static int omap_hsmmc_disable_fclk(struc
>>>>> return 0;
>>>>> }
>>>>>
>>>>> +static void omap_hsmmc_enable_sdio_irq(struct mmc_host *mmc, int
>>>>> enable)
>>>>> +{
>>>>> + struct omap_hsmmc_host *host = mmc_priv(mmc);
>>>>> + u32 ie, ise;
>>>>> +
>>>>> + ise = OMAP_HSMMC_READ(host->base, ISE);
>>>>> + ie = OMAP_HSMMC_READ(host->base, IE);
>>>>> +
>>>>> + if (enable) {
>>>>> + OMAP_HSMMC_WRITE(host->base, ISE, ise | CIRQ_ENABLE);
>>>>> + OMAP_HSMMC_WRITE(host->base, IE, ie | CIRQ_ENABLE);
>>>>> + } else {
>>>>> + OMAP_HSMMC_WRITE(host->base, ISE, ise & ~CIRQ_ENABLE);
>>>>> + OMAP_HSMMC_WRITE(host->base, IE, ie & ~CIRQ_ENABLE);
>>>>> + }
>>>>> +
>>>>> +}
>>>>> +
>>>>> static const struct mmc_host_ops omap_hsmmc_ops = {
>>>>> .enable = omap_hsmmc_enable_fclk,
>>>>> .disable = omap_hsmmc_disable_fclk,
>>>>> @@ -1519,7 +1557,7 @@ static const struct mmc_host_ops omap_hs
>>>>> .set_ios = omap_hsmmc_set_ios,
>>>>> .get_cd = omap_hsmmc_get_cd,
>>>>> .get_ro = omap_hsmmc_get_ro,
>>>>> - /* NYET -- enable_sdio_irq */
>>>>> + .enable_sdio_irq = omap_hsmmc_enable_sdio_irq,
>>>>> };
>>>>>
>>>>> static const struct mmc_host_ops omap_hsmmc_ps_ops = {
>>>>> @@ -1529,7 +1567,7 @@ static const struct mmc_host_ops omap_hs
>>>>> .set_ios = omap_hsmmc_set_ios,
>>>>> .get_cd = omap_hsmmc_get_cd,
>>>>> .get_ro = omap_hsmmc_get_ro,
>>>>> - /* NYET -- enable_sdio_irq */
>>>>> + .enable_sdio_irq = omap_hsmmc_enable_sdio_irq,
>>>>> };
>>>>>
>>>>> #ifdef CONFIG_DEBUG_FS
>>>>> @@ -1734,7 +1772,7 @@ static int __init omap_hsmmc_probe(struc
>>>>> mmc->max_seg_size = mmc->max_req_size;
>>>>>
>>>>> mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED |
>>>>> - MMC_CAP_WAIT_WHILE_BUSY;
>>>>> + MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_SDIO_IRQ;
>>>>>
>>>>> if (mmc_slot(host).wires >= 8)
>>>>> mmc->caps |= MMC_CAP_8_BIT_DATA;
>>>>>
>>>>>
>>>
>>
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
