hmm,,i boot again and kernel panic cannot sync VFS because no respond from my nfs server... but i'm try to mount y nfs directory in the another computer, it's work..i don't know whre is the problem? On 8/16/09, Kovacs Peter Tamas <p.kovacs@xxxxxxxxxxxxxxx> wrote: > Hi, > > I don't think that it's a problem with the filesystem, if you followed > the tutorial then you have the filesystem on the second partition, and > your bootargs are pointing there too. > Do you have a DHCP server running somewhere? > If you have DHCP, but the OMAP cannot use it for some reason, you can > still try forcing a static IP instead of DHCPing, like discussed here: > http://focus.ti.com/lit/an/spraaq0/spraaq0.pdf > > That is, add something like > ip=clientIP:serverIP:gatewayIP:netMask:::off > to your bootargs. > More info about the meaning of the above here: > http://www.kernel.org/pub/linux/kernel/people/marcelo/linux-2.4/Documentation/nfsroot.txt > > Peter >> thanks peter, i can boot but the kernel stop in the >> Sending DHCP Requests . <7>hub 1-0:1.0 hub_suspend >> ....... >> >> how to boot filesystems has installed from mmc?...thanks >> >> On 8/16/09, Tar Gz <bsdraisefromhell@xxxxxxxxx> wrote: >> >>> thanks mr.peter >>> >>> i should try the command like that >>> >>> #nand unlock >>> #nand ecc sw >>> #setenv bootargs 'console=ttyS3,115200n8 root=/dev/mmcblk0p2 rw >>> rootdelay=1 mem=256M init=/init' >>> #setenv bootcmd 'mmcinit; fatload mmc 0 0x80c00000 uImage; bootm >>> 0x80c00000' >>> #saveenv >>> #boot >>> >>> it is stop(like hang) and i must restart again >>> >>> On 8/16/09, Kovacs Peter Tamas <p.kovacs@xxxxxxxxxxxxxxx> wrote: >>> >>>> Dear Aldyth, >>>> >>>> u-boot stops and waits for your command to load and start the kernel, as >>>> the bootcmd is not doing it automatically with your setup (setting >>>> bootargs is not enough alone, you need to load the kernel image from the >>>> card and run it). >>>> You should try: >>>> mmcinit >>>> fatload mmc 0 80300000 uImage >>>> bootm 80300000 >>>> >>>> As described at eg: >>>> http://www.codeshogun.com/blog/2009/04/15/porting-android-to-beagle-board/ >>>> >>>> Hope this helps, >>>> Peter >>>> >>>>> it is my step to build u-boot, x-loader and kernel >>>>> >>>>> i'm try linux 2.6.30 and using the omap3430sdp_defconfig to build the >>>>> uImage >>>>> >>>>> my u-boot and x-loader using omap3430zoom2_config >>>>> >>>>> any idea to solve that problem?... >>>>> >>>>> regards, >>>>> Aldyth M >>>>> >>>>> On 8/16/09, Tar Gz <bsdraisefromhell@xxxxxxxxx> wrote: >>>>> >>>>> >>>>>> i'm format mmc in the fat win95... >>>>>> >>>>>> i following step by step in the >>>>>> https://omapzoom.org/gf/project/omapkernel/wiki/?pagename=Getting+Stated+with+Linux+OMAP+Kernel >>>>>> >>>>>> why can't read? >>>>>> >>>>>> On 8/16/09, Tar Gz <bsdraisefromhell@xxxxxxxxx> wrote: >>>>>> >>>>>> >>>>>>> i'm format mmc in the fat win95... >>>>>>> >>>>>>> i following step by step in the >>>>>>> https://omapzoom.org/gf/project/omapkernel/wiki/?pagename=Getting+Stated+with+Linux+OMAP+Kernel >>>>>>> >>>>>>> why can't read? >>>>>>> >>>>>>> >>>>>>> >>>>>>>> On 8/16/09, Felipe Balbi <me@xxxxxxxxxxxxxxx> wrote: >>>>>>>> >>>>>>>> >>>>>>>>> Hi, >>>>>>>>> >>>>>>>>> On Sun, Aug 16, 2009 at 12:48:52PM -0400, Tar Gz wrote: >>>>>>>>> >>>>>>>>> >>>>>>>>>> Hi all,,i'm sorry if my english too bad >>>>>>>>>> >>>>>>>>>> i try to porting linux kernel 2.6.30 from kernel.org into omap >>>>>>>>>> 3430 >>>>>>>>>> >>>>>>>>>> i have the problem linux kernel can't booting >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> i'm following step by step in the omapzoom.org >>>>>>>>>> $ setenv bootargs console=ttyS3,115200n8 root=/dev/mmcblk0p2 rw >>>>>>>>>> rootdelay=1 mem=256M init=/sbin/init >>>>>>>>>> $ saveenv >>>>>>>>>> $ bootd >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> OMAP34XX LAB # print >>>>>>>>>> bootdelay=3 >>>>>>>>>> baudrate=115200 >>>>>>>>>> bootargs=console=ttyS3,115200n8 root=/dev/mmcblk0p2 rootdelay=1 >>>>>>>>>> mem=256M init=/sbin/init >>>>>>>>>> bootcmd=mmcinit >>>>>>>>>> bootfile="uImage" >>>>>>>>>> >>>>>>>>>> if i'm type bootd i'm still in the konsole like this, >>>>>>>>>> OMAP34XX LAB # bootd >>>>>>>>>> OMAP34XX LAB # >>>>>>>>>> >>>>>>>>>> any idea? >>>>>>>>>> >>>>>>>>>> >>>>>>>>> you're not reading the kernel image to memory. >>>>>>>>> >>>>>>>>> is your mmc formated with FAT32 or what ? >>>>>>>>> >>>>>>>>> You need to read kernel from mmc to memory and boot from there. >>>>>>>>> >>>>>>>>> -- >>>>>>>>> balbi >>>>>>>>> >>>>>>>>> >>>>>>>>> >>>>> -- >>>>> To unsubscribe from this list: send the line "unsubscribe linux-omap" >>>>> in >>>>> the body of a message to majordomo@xxxxxxxxxxxxxxx >>>>> More majordomo info at http://vger.kernel.org/majordomo-info.html >>>>> >>>>> >>>> >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-omap" in >> the body of a message to majordomo@xxxxxxxxxxxxxxx >> More majordomo info at http://vger.kernel.org/majordomo-info.html >> > > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
