thanks mr.peter i should try the command like that #nand unlock #nand ecc sw #setenv bootargs 'console=ttyS3,115200n8 root=/dev/mmcblk0p2 rw rootdelay=1 mem=256M init=/init' #setenv bootcmd 'mmcinit; fatload mmc 0 0x80c00000 uImage; bootm 0x80c00000' #saveenv #boot it is stop(like hang) and i must restart again On 8/16/09, Kovacs Peter Tamas <p.kovacs@xxxxxxxxxxxxxxx> wrote: > Dear Aldyth, > > u-boot stops and waits for your command to load and start the kernel, as > the bootcmd is not doing it automatically with your setup (setting > bootargs is not enough alone, you need to load the kernel image from the > card and run it). > You should try: > mmcinit > fatload mmc 0 80300000 uImage > bootm 80300000 > > As described at eg: > http://www.codeshogun.com/blog/2009/04/15/porting-android-to-beagle-board/ > > Hope this helps, > Peter >> it is my step to build u-boot, x-loader and kernel >> >> i'm try linux 2.6.30 and using the omap3430sdp_defconfig to build the >> uImage >> >> my u-boot and x-loader using omap3430zoom2_config >> >> any idea to solve that problem?... >> >> regards, >> Aldyth M >> >> On 8/16/09, Tar Gz <bsdraisefromhell@xxxxxxxxx> wrote: >> >>> i'm format mmc in the fat win95... >>> >>> i following step by step in the >>> https://omapzoom.org/gf/project/omapkernel/wiki/?pagename=Getting+Stated+with+Linux+OMAP+Kernel >>> >>> why can't read? >>> >>> On 8/16/09, Tar Gz <bsdraisefromhell@xxxxxxxxx> wrote: >>> >>>> i'm format mmc in the fat win95... >>>> >>>> i following step by step in the >>>> https://omapzoom.org/gf/project/omapkernel/wiki/?pagename=Getting+Stated+with+Linux+OMAP+Kernel >>>> >>>> why can't read? >>>> >>>> >>>>> On 8/16/09, Felipe Balbi <me@xxxxxxxxxxxxxxx> wrote: >>>>> >>>>>> Hi, >>>>>> >>>>>> On Sun, Aug 16, 2009 at 12:48:52PM -0400, Tar Gz wrote: >>>>>> >>>>>>> Hi all,,i'm sorry if my english too bad >>>>>>> >>>>>>> i try to porting linux kernel 2.6.30 from kernel.org into omap 3430 >>>>>>> >>>>>>> i have the problem linux kernel can't booting >>>>>>> >>>>>>> >>>>>>> i'm following step by step in the omapzoom.org >>>>>>> $ setenv bootargs console=ttyS3,115200n8 root=/dev/mmcblk0p2 rw >>>>>>> rootdelay=1 mem=256M init=/sbin/init >>>>>>> $ saveenv >>>>>>> $ bootd >>>>>>> >>>>>>> >>>>>>> OMAP34XX LAB # print >>>>>>> bootdelay=3 >>>>>>> baudrate=115200 >>>>>>> bootargs=console=ttyS3,115200n8 root=/dev/mmcblk0p2 rootdelay=1 >>>>>>> mem=256M init=/sbin/init >>>>>>> bootcmd=mmcinit >>>>>>> bootfile="uImage" >>>>>>> >>>>>>> if i'm type bootd i'm still in the konsole like this, >>>>>>> OMAP34XX LAB # bootd >>>>>>> OMAP34XX LAB # >>>>>>> >>>>>>> any idea? >>>>>>> >>>>>> you're not reading the kernel image to memory. >>>>>> >>>>>> is your mmc formated with FAT32 or what ? >>>>>> >>>>>> You need to read kernel from mmc to memory and boot from there. >>>>>> >>>>>> -- >>>>>> balbi >>>>>> >>>>>> >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-omap" in >> the body of a message to majordomo@xxxxxxxxxxxxxxx >> More majordomo info at http://vger.kernel.org/majordomo-info.html >> > > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
