thanks peter, i can boot but the kernel stop in the Sending DHCP Requests . <7>hub 1-0:1.0 hub_suspend ....... how to boot filesystems has installed from mmc?...thanks On 8/16/09, Tar Gz <bsdraisefromhell@xxxxxxxxx> wrote: > thanks mr.peter > > i should try the command like that > > #nand unlock > #nand ecc sw > #setenv bootargs 'console=ttyS3,115200n8 root=/dev/mmcblk0p2 rw > rootdelay=1 mem=256M init=/init' > #setenv bootcmd 'mmcinit; fatload mmc 0 0x80c00000 uImage; bootm > 0x80c00000' > #saveenv > #boot > > it is stop(like hang) and i must restart again > > On 8/16/09, Kovacs Peter Tamas <p.kovacs@xxxxxxxxxxxxxxx> wrote: >> Dear Aldyth, >> >> u-boot stops and waits for your command to load and start the kernel, as >> the bootcmd is not doing it automatically with your setup (setting >> bootargs is not enough alone, you need to load the kernel image from the >> card and run it). >> You should try: >> mmcinit >> fatload mmc 0 80300000 uImage >> bootm 80300000 >> >> As described at eg: >> http://www.codeshogun.com/blog/2009/04/15/porting-android-to-beagle-board/ >> >> Hope this helps, >> Peter >>> it is my step to build u-boot, x-loader and kernel >>> >>> i'm try linux 2.6.30 and using the omap3430sdp_defconfig to build the >>> uImage >>> >>> my u-boot and x-loader using omap3430zoom2_config >>> >>> any idea to solve that problem?... >>> >>> regards, >>> Aldyth M >>> >>> On 8/16/09, Tar Gz <bsdraisefromhell@xxxxxxxxx> wrote: >>> >>>> i'm format mmc in the fat win95... >>>> >>>> i following step by step in the >>>> https://omapzoom.org/gf/project/omapkernel/wiki/?pagename=Getting+Stated+with+Linux+OMAP+Kernel >>>> >>>> why can't read? >>>> >>>> On 8/16/09, Tar Gz <bsdraisefromhell@xxxxxxxxx> wrote: >>>> >>>>> i'm format mmc in the fat win95... >>>>> >>>>> i following step by step in the >>>>> https://omapzoom.org/gf/project/omapkernel/wiki/?pagename=Getting+Stated+with+Linux+OMAP+Kernel >>>>> >>>>> why can't read? >>>>> >>>>> >>>>>> On 8/16/09, Felipe Balbi <me@xxxxxxxxxxxxxxx> wrote: >>>>>> >>>>>>> Hi, >>>>>>> >>>>>>> On Sun, Aug 16, 2009 at 12:48:52PM -0400, Tar Gz wrote: >>>>>>> >>>>>>>> Hi all,,i'm sorry if my english too bad >>>>>>>> >>>>>>>> i try to porting linux kernel 2.6.30 from kernel.org into omap 3430 >>>>>>>> >>>>>>>> i have the problem linux kernel can't booting >>>>>>>> >>>>>>>> >>>>>>>> i'm following step by step in the omapzoom.org >>>>>>>> $ setenv bootargs console=ttyS3,115200n8 root=/dev/mmcblk0p2 rw >>>>>>>> rootdelay=1 mem=256M init=/sbin/init >>>>>>>> $ saveenv >>>>>>>> $ bootd >>>>>>>> >>>>>>>> >>>>>>>> OMAP34XX LAB # print >>>>>>>> bootdelay=3 >>>>>>>> baudrate=115200 >>>>>>>> bootargs=console=ttyS3,115200n8 root=/dev/mmcblk0p2 rootdelay=1 >>>>>>>> mem=256M init=/sbin/init >>>>>>>> bootcmd=mmcinit >>>>>>>> bootfile="uImage" >>>>>>>> >>>>>>>> if i'm type bootd i'm still in the konsole like this, >>>>>>>> OMAP34XX LAB # bootd >>>>>>>> OMAP34XX LAB # >>>>>>>> >>>>>>>> any idea? >>>>>>>> >>>>>>> you're not reading the kernel image to memory. >>>>>>> >>>>>>> is your mmc formated with FAT32 or what ? >>>>>>> >>>>>>> You need to read kernel from mmc to memory and boot from there. >>>>>>> >>>>>>> -- >>>>>>> balbi >>>>>>> >>>>>>> >>> -- >>> To unsubscribe from this list: send the line "unsubscribe linux-omap" in >>> the body of a message to majordomo@xxxxxxxxxxxxxxx >>> More majordomo info at http://vger.kernel.org/majordomo-info.html >>> >> >> > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
