* Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxxxx> [170829 02:18]:
> Hi,
>
> On Mon, Aug 28, 2017 at 02:19:09PM -0700, Tony Lindgren wrote:
> > On omap4 we're missing the hsi node with it's related "ti,hwmods"
> > property that the SoC interconnect code needs.
> >
> > Note that this will only show up as a bug with "doesn't have
> > mpu register target base" boot errors when the legacy platform
> > data is removed.
> >
> > Let's also update the binding accrodingly while at it.
> >
> > Cc: Sebastian Reichel <sre@xxxxxxxxxx>
> > Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
> > ---
> > Documentation/devicetree/bindings/hsi/omap-ssi.txt | 6 +++++-
> > arch/arm/boot/dts/omap4.dtsi | 9 +++++++++
> > 2 files changed, 14 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/hsi/omap-ssi.txt b/Documentation/devicetree/bindings/hsi/omap-ssi.txt
> > --- a/Documentation/devicetree/bindings/hsi/omap-ssi.txt
> > +++ b/Documentation/devicetree/bindings/hsi/omap-ssi.txt
> > @@ -4,7 +4,7 @@ OMAP Synchronous Serial Interface (SSI) controller implements a legacy
> > variant of MIPI's High Speed Synchronous Serial Interface (HSI).
> >
> > Required properties:
> > -- compatible: Should include "ti,omap3-ssi".
> > +- compatible: Should include "ti,omap3-ssi" or "ti,omap4-hsi"
> > - reg-names: Contains the values "sys" and "gdd" (in this order).
> > - reg: Contains a matching register specifier for each entry
> > in reg-names.
> > @@ -38,6 +38,10 @@ Required Port sub-node properties:
> > property. If it's missing the port will not be
> > enabled.
> >
> > +Optional properties:
> > +- ti,hwmods: Shall contain TI interconnect module name if needed
> > + by the SoC
> > +
> > Example for Nokia N900:
> >
> > ssi-controller@48058000 {
> > diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
> > --- a/arch/arm/boot/dts/omap4.dtsi
> > +++ b/arch/arm/boot/dts/omap4.dtsi
> > @@ -632,6 +632,15 @@
> > dma-names = "tx", "rx";
> > };
> >
> > + hsi: hsi@4a058000 {
> > + compatible = "ti,omap4-hsi";
> > + reg = <0x4a058000 0x4000>;
> > + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
> > + ti,hwmods = "hsi";
> > + };
> > +
>
> This does not follow the binding, which expects one subnode per
> port and splits memory areas + interrupts accordingly. Fortunately
> HSI is properly documented in the public OMAP4 TRM (in opposit to
> SSI, which is missing completly in OMAP3 TRM). I think the node
> should look like this:
OK sure let's add the subnodes too :)
> hsi: hsi@4a058000 {
> compatible = "ti,omap4-hsi";
> ti,hwmods = "hsi";
>
> reg = <0x4a058000 0x5000>,
> <0x4a058000 0x1000>;
> reg-names = "sys", "gdd";
The module size is 0x4000 in the hardware. Then there's the L4
interconnect registers at 0x5c000 0x1000:
reg = <0x4a058000 0x4000>,
<0x4a05c000 0x1000>;
reg-names = "sys", "gdd";
Hmm, what's the "gdd" name for? Probably it would be be to use "ta"
there for "target agent" as that's generic and available for every
module.
> clocks = <&hsi_fck>;
> clock-names = "hsi_fck";
>
> interrupts = <71>;
> interrupt-names = "gdd_mpu";
And the interrupts need to be mapped for omap4. I'll post
v2 with the subnodes.
Regards,
Tony
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
