* Ladislav Michl <ladis@xxxxxxxxxxxxxx> [161104 03:41]:
> All your patches on top of current Linus' git and revert of:
> commit 87326e858448c40e32f142c0b8dcc59d7b27c641
> Author: Tony Lindgren <tony@xxxxxxxxxxx>
> Date: Tue May 31 10:05:20 2016 -0500
>
> usb: musb: Remove extra PM runtime calls from 2430 glue layer
>
> does the trick for me (reverted patch which applies bellow). I also
> alternatively tried to increase pm_runtime_set_autosuspend_delay up
> to 1000 without luck.
OK thanks for narrowing it down. The patch does not seem to change
anything for me with 2430 glue layer, things work for me with and
without it. Care to check if all hunks of the patch are needed
for you..
> diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
> index 451b372..a623e45 100644
> --- a/drivers/usb/musb/omap2430.c
> +++ b/drivers/usb/musb/omap2430.c
> @@ -218,8 +218,13 @@ static void omap_musb_mailbox_work(struct work_struct *mailbox_work)
> {
> struct omap2430_glue *glue = container_of(mailbox_work,
> struct omap2430_glue, omap_musb_mailbox_work);
> + struct musb *musb = glue_to_musb(glue);
> + struct device *dev = musb->controller;
>
> + pm_runtime_get_sync(dev);
> omap_musb_set_mailbox(glue);
> + pm_runtime_mark_last_busy(dev);
> + pm_runtime_put_autosuspend(dev);
> }
>
> static irqreturn_t omap2430_musb_interrupt(int irq, void *__hci)
..is just the above enough..
> @@ -289,6 +294,16 @@ static int omap2430_musb_init(struct musb *musb)
> phy_init(musb->phy);
> phy_power_on(musb->phy);
>
> + /*
> + * Enable runtime PM for musb parent (this driver). We can't
> + * do it earlier as struct musb is not yet allocated and we
> + * need to touch the musb registers for runtime PM.
> + */
> + pm_runtime_enable(glue->dev);
> + status = pm_runtime_get_sync(glue->dev);
> + if (status < 0)
> + goto err1;
> +
> l = musb_readl(musb->mregs, OTG_INTERFSEL);
>
> if (data->interface_type == MUSB_INTERFACE_UTMI) {
> @@ -312,7 +327,11 @@ static int omap2430_musb_init(struct musb *musb)
> if (glue->status != MUSB_UNKNOWN)
> omap_musb_set_mailbox(glue);
>
> + pm_runtime_put(glue->dev);
> return 0;
> +
> +err1:
> + return status;
> }
>
> static void omap2430_musb_enable(struct musb *musb)
> @@ -512,10 +531,6 @@ static int omap2430_probe(struct platform_device *pdev)
> goto err2;
> }
>
> - pm_runtime_enable(glue->dev);
> - pm_runtime_use_autosuspend(glue->dev);
> - pm_runtime_set_autosuspend_delay(glue->dev, 100);
> -
> ret = platform_device_add(musb);
> if (ret) {
> dev_err(&pdev->dev, "failed to register musb device\n");
> @@ -538,7 +553,6 @@ static int omap2430_remove(struct platform_device *pdev)
> pm_runtime_get_sync(glue->dev);
> platform_device_unregister(glue->musb);
> pm_runtime_put_sync(glue->dev);
> - pm_runtime_dont_use_autosuspend(glue->dev);
> pm_runtime_disable(glue->dev);
>
> return 0;
..or are these init changes needed too?
Regards,
Tony
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
