On Fri, Feb 26, 2016 at 12:14:44PM +0200, Jyri Sarha wrote:
> On 02/26/16 02:43, Russell King - ARM Linux wrote:
> >On Thu, Feb 25, 2016 at 03:42:50PM +0200, Jyri Sarha wrote:
> >>On 02/18/16 16:35, Rob Herring wrote:
> >>>This should be implied from the port unit address. In other words,
> >>>port@0 is defined to be the rgb port. Now, if this is one of several
> >>>modes for the video port, then that is a different story.
> >>>
> >>
> >>Do you suggest that also the audio i2s and s/p-dif port-types should be
> >>coded in the port unit addresses? Something like: port@0 is always rgb,
> >>port@1 is i2s, and port@2 is spdif?
> >
> >For the audio inputs, the port address corresponds to the input pin.
> >TDA998x devices can have multiple streams routed to the pins, and can
> >select between them.
> >
> >For example, there may be four I2S data pins and one I2S clock pin.
> >When using stereo, you can select which of the four I2S data pins
> >carries the audio data.
> >
>
> Sure, but I do not think that would be the usual setup. The only "normal"
> situation I can think for having a need to have two alternative audio setups
> would one for i2s and another for s/p-dif. But then again it is possible to
> come up with a design with multiple alternative audio wirings and it
> relatively simple handle that in DT binding, so why not.
There's another reason: if you want to support 8 channel audio using I2S
rather than SPDIF, then you need to use four I2S data inputs. Each I2S
data input can support only two channels.
> >When using SPDIF, there may be two SPDIF inputs, and you can select
> >which SPDIF input is used.
> >
> >So, "reg" may not be an address in terms of a CPU visible address, but
> >it's an address as far as selecting the appropriate input - and it
> >fits in with the requirements of ePAPR, which are that if you have
> >a unit-address (which is required to distinguish different port nodes)
> >then you must have a matching "reg" property.
>
> Still I do not see why it is desirable to reuse reg property, when we can
> introduce new property for describing the audio wiring.
Different people have different opinions. Your opinion is just another
example of someone holding a different view.
You _have_ to have a unit address, and therefore you _have_ to have a
reg property. If you want to use some other property to describe the
audio input pin, then you will need to make up a totally ficticious
unit-address and reg property for each audio input pin.
That's adding complexity, arguably unnecessary complexity, and making
the binding unnecessarily more complex for no good reason.
> >I don't particularly like the video node using the RGB routing register
> >value either for the reg property, but I've kept quiet because I have
> >nothing to offer there: again, this comes down to ePAPR requirements
> >and the need to specify multiple "port { }" nodes. You can't have two
> >"port { }" nodes without using a unit-address, and we'd need to chose
> >a unit-address for it which doesn't conflict with the audio ports...
> >so there's a kind of logic to using the RGB routing value, which will
> >never conflict.
> >
>
> If we after all decide to go with using reg property for audio wiring (and
> essentially writing the value directly to AP_ENA register), then we could
> also agree that video port's unit address is always 0 as it corresponds to
> audio disabled in AP_ENA register and would not collide with any audio
> "address". Then we could keep the old video-ports property to configure the
> video wiring. How does this sound?
Sub-standard :)
This has actually been discussed before. See the thread:
"[PATCH v9 1/4] drm/i2c: tda998x: Add DT support for audio"
from January 2015.
--
RMK's Patch system: http://www.arm.linux.org.uk/developer/patches/
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
